Articulating Hitch (Offset)
Show/hide table
| |
| Illustration 1 | g03361438 |
Show/hide table
| Specification for 351-3406 Articulating Hitch Gp | |||
| Item | Qty | Part | Specification Description |
| Prior to bearing assembly clean bore to remove all oil, grease, scale, dirt, and other surface contamination. | |||
| 1 | 2 | 358-6705 Pin As | Diameter is |
| 2 | 1 | 364-3603 Pin As | Diameter is |
| 3 | 1 | 364-3602 Pin | Diameter is |
| 4 | 8 | 112-3930 Bolt | Use the following procedure to tighten the bolts:
1. Before assembly, apply red Loctite 271 to the threads. 2. Tighten inside bolts on the top and the bottom to 3. Tighten outside bolts on the top and the bottom to 4. Repeat the procedure if required further tightening. 5. After you tighten, maintain a minimum gap of |
Show/hide table
| |
| Illustration 2 | g03361439 |
Show/hide table
| 5 | - | - | Before assembly, lightly lubricate this surface with lubricant that is being sealed. |
| 6 | 1 | 2P-1279 Locknut | Before assembly, apply blue Loctite 242 to the threads.
Torque to |
| 7 | 1 | 8S-6959 Lip Type Seal | Install seals with the lips facing outward. Spring should be visible. |
| 8 | As required, use the following shims during bearing preload procedure: | ||
| 1 | 365-0067 Shim | Thickness of one shim is |
|
| 1 | 365-0066 Shim | Thickness of one shim is |
|
| 9 | Install shims as required, to eliminate gaps between plate and surface: | ||
| 2 | 363-9168 Shim | Thickness of one shim is |
|
| 2 | 363-9167 Shim | Thickness of one shim is |
|
| 2 | 361-1901 Shim | Thickness of one shim is |
|
| 10 | 2 | 3K-6454 Lip Type Seal | Install seals with the lips facing outward. Spring should be visible.
Lightly lubricate with the lubricant that is being sealed. |
Caterpillar Information System:
307D Excavator Machine System Specifications Swing Motor Lines
308E CR Mini Hydraulic Excavator Machine System Specifications Coupler Lines
PC104B and PC205B Cold Planers Work Tool Installation and Removal
2012/06/20 An Improved Lock Assembly for the Toolbox is Now Used on Certain Excavators and Mobile Hydraulic Power Units {7268}
Procedure to Rework Bucket Pin Bores on Certain 980H and 980K Wheel Loaders{6101, 6102, 6108} Procedure to Rework Bucket Pin Bores on Certain 980H and 980K Wheel Loaders{6101, 6102, 6108}
307D Excavator Machine System Specifications Hydraulic Tank Mounting
307D Excavator Machine System Specifications Stick Cylinder Lines
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Water Spray Lines
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Eccentric Weight Housing Group
CD44B and CD54B Vibratory Asphalt Compactors Machine Systems Eccentric Weight Housing Group
307D Excavator Machine System Specifications Return Lines
308E2 CR and 308E2 SR Mini Hydraulic Excavators Machine System Specifications Cutting Edge
CB44B and CB54B Vibratory Asphalt Compactors Machine Systems Suction Fan
308E2 CR Mini Hydraulic Excavator Machine System Specifications Boom Cylinder
308E CR Mini Hydraulic Excavator Machine System Specifications Boom Cylinder
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Flow Control Valve (Steering)
307D Excavator Machine System Specifications Front Lines
CD44B and CD54B Vibratory Asphalt Compactors Machine Systems Window Wiper and Wiper Motor
308ECR and 308ESR Mini Hydraulic Excavators Machine Systems Evaporator Coil - Remove and Install
826K Landfill Compactor Mirror
307D Excavator Machine System Specifications Front Lines
307D Excavator Machine System Specifications Front Lines
308E CR Mini Hydraulic Excavator Hydraulic System Travel System
307D Excavator Machine System Specifications Front Lines