Fuel Filter and Base - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 2P-8250     | 带式扳手组件     | 1     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这将有助于防止污垢进入部件的内部。
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 塞住所有管路、软管和管子。 这将有助于防止液体泄漏和防止污染物进入系统。
- 拆下端盖组件 (1) 。
Show/hide table
图 1 | g01217087 |
- 关闭阀门组件 (2) 。
Show/hide table
图 2 | g01217089 |
- 断开线束组件 (3) 。 断开软管组件 (4) 。 使用工具 (A) 以便拆下滤清器组件 (5) 。 拆下螺栓 (6) 。 拆下燃油滤清器底座 (7) 。
Show/hide table
图 3 | g01217091 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 2P-8250     | 带式扳手组件     | 1     |
注: 清洁度是一项重要的因素。 安装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 安装燃油滤清器底座 (7) 。 安装螺栓 (6) 。 使用工具 (A) 安装滤清器组件 (5) 。 连接软管组件 (4) 。 连接线束组件 (3) 。
Show/hide table
图 4 | g01217091 |
- 打开阀门组件 (2) 。
Show/hide table
图 5 | g01217089 |
- 安装盖组件 (1) 。
Show/hide table
图 6 | g01217087 |
Caterpillar Information System:
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit C7 Engine Supplement Cylinder Head - Install
416E Backhoe Loader Differential Oil Sample (Rear) - Obtain
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Fuel Filter Differential Pressure Switch Circuit - Test
C9.3 Engine for Caterpillar Built Machines Engine Oil Pan
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Travel on Level Ground - Test
M330D Material Handler Joystick Controls - Material Handler
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Engine Performance - Test - Engine Speed
2005/11/28 The Addition of an Abrasion Sleeve Protects the Hose Assemblies in the Bucket Lines Gp {5057}
C9.3 Engine for Caterpillar Built Machines Engine Oil Filter Base
320D RR Excavator and 320D RR Forest Machine Machine System Specifications Boom - 5.675 m (18.62 ft)
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System System 17: Relief Valve (Line) - Test and Adjust - Auxiliary Control Valve
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System System 17: Relief Valve (Main) - Test and Adjust - Auxiliary Control Valve (Medium Pressure)
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Cylinder Drift - Check
324D Excavator Machine System Specifications Stick - 2.5 m (8.20 ft)
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Cylinder Speed - Check
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit C7 Engine Supplement Water Separator and Fuel Priming Pump - Remove and Install
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Relief Valve (Pilot) - Test and Adjust
M330D Material Handler Engine Starting
M325D MH Material Handler Access Door and Cover Locations
M325D MH Material Handler Braking System - Test
M325D MH Material Handler Cooling System Coolant (ELC) - Change
305D CR and 305.5D CR Mini Hydraulic Excavators Machine System Specifications Stick
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Relief Valve (Main) - Test and Adjust