Valve Mechanism Cover - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-8440     | 部件清洁剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下发动机机油加注口盖(如有配备)。
Show/hide table
图 1 | g00886209 |
- 从气门机构盖 (3) 上拆下螺栓 (1) 和垫圈 (2) 。
- 拆下气门机构盖 (4) 和密封垫 (3) 。
- 使用工具 (A) 清洁气门机构盖 (3) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
B     | 154-8874     | 粘接剂套件     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (B) 将粘接剂涂覆到气门机构盖 (3) 上。
Show/hide table
图 2 | g00886209 |
注: 对于较新的一侧上带有橡胶条的气门室盖密封垫,不需要使用粘接剂。 密封垫设计为采用干式安装。
- 安装新密封垫 (4) 和气门机构盖 (3) 。
- 安装垫圈 (2) 和螺栓 (1) 。
- 按数字顺序拧紧螺栓至扭矩为 12 ± 3 N·m (106 ± 27 lb in)。
Show/hide table
图 3 | g00611545 |
发动机气门室盖的拧紧顺序 (A) 后 (B) 前 |
- 安装发动机机油加注口盖(如有配备)。
Caterpillar Information System:
3054B Industrial Engine Piston and Rings
3054B Industrial Engine Water Pump
Caterpillar Monitoring System for Electronic Modular Control Panel LH/RH Switch - Troubleshoot
Caterpillar Monitoring System for Electronic Modular Control Panel Connector Contact Description of Main Display Module
Caterpillar Monitoring System for Electronic Modular Control Panel Glossary of Terms
Caterpillar Monitoring System for Electronic Modular Control Panel Electrical Connector - Inspect
Caterpillar Monitoring System for Electronic Modular Control Panel System Self Test
Caterpillar Monitoring System for Electronic Modular Control Panel Harness Code - Troubleshoot
Caterpillar Monitoring System for Electronic Modular Control Panel Main Display Module Initialization - Adjust
3054 and 3056 Industrial and Generator Set Engines Engine Oil Pressure
C-9 Engines for Caterpillar Built Machines Injection Actuation Oil Temperature Sensor
Battery Test Procedure {1401} Battery Test Procedure {1401}
3054B Industrial Engine Connecting Rod
C-9 Engines for Caterpillar Built Machines Cylinder Liner Projection - Inspect
3126B Marine Engine Fuel Filter Base - Remove and Install
3126B Marine Engine Engine Oil Filter Base - Remove
3126B Marine Engine Engine Oil Filter Base - Install
3126B Marine Engine Valve Mechanism Cover - Remove and Install
3054B Industrial Engine Engine Oil Pressure
3126B Marine Engine Belt Tensioner - Remove and Install
C-9 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3126B Marine Engine Fuel Priming Pump - Remove and Install
3126B Marine Engine Electronic Control Module - Remove and Install
C-9 Engines for Caterpillar Built Machines Electronic Unit Injector - Test