Inlet and Exhaust Valve Guides - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6895 或 4C-6366 (1)     |
气门导管冲头     | 1     |
Show/hide table
( 1 ) | 如有必要,使用工具拆卸进气门导管。 |
开始:
- 拆下进气门和排气门。 请参阅拆解和组装, "进气门和排气门 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 从缸盖组件上拆下进气门导管和排气门导管。
Show/hide table
图 1 | g01137612 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6895 或 4C-6366 (1)     |
气门导管冲头     | 1     |
B     | 173-5524     | 导向圈     | 1     |
C     | 342-6109     | 导向圈     | 1     |
Show/hide table
( 1 ) | 如有必要,使用工具拆卸进气门导管。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在缸盖中定位进气门导管和排气门导管。 轻敲气门导管的顶部,使进气门导管和排气门导管开始进入缸盖组件。
Show/hide table
图 2 | g03317961 |
- 使用工具 (A) 和工具 (B) 安装排气门导管。 使用工具 (A) 和工具 (C) 安装进气门导管。 安装气门导管,直到凸出量达到尺寸 (X) 。 尺寸 (X) 为高于缸盖组件 12.0 ± 0.5 mm (0.47 ± 0.02 in)。
End By: 安装进气门和排气门。 请参阅 拆解和组装, "进气门和排气门 - 拆卸和安装"。
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Block Diagram of Generator Set Control
3406E On-Highway Engine Exhaust Manifold - Remove and Install
3612 and 3616 Engines Engine Oil Filter Housings - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Pulse Width Modulated (PWM) Sensor - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Starting Motor Magnetic Switch - Test
C9 Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
3500 Engines for Caterpillar Built Generator Sets Fuel Pressure Regulator
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Speed Sensor (Engine) - Adjust
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Alarm Module Control - Adjust
G3304 and G3306 Engines Governor Linkage
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines AC Voltage Range - Adjust
G3304 and G3306 Engines Governor Linkage - Woodward PSG Governor For Turbocharged Engines
3612 and 3616 Engines Engine Oil Filter Housings - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (AC Transformer Box) - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Relay Module - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Replace
SR500 Generators Bearing (Spherical Roller) - Lubricate
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Typical Generator Abbreviations
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Symbols
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Reading DC Schematics
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Record
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3618 Engine Crankshaft Rear Gear - Remove and Install