Engine Oil Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有关发动机机油泵可再用性信息,请参阅再使用零件和修补操作指南, SEBF8167, "3114 和 3116 发动机修复步骤"。
- 组装前,确保机油泵的所有零件完全洁净。
注: 利用洁净的机油润滑机油泵的所有内构件。
- 将机油卸压柱塞 (13) 和弹簧 (14) 安装到机油泵壳体组件 (7) 内。 安装垫圈和螺栓。
Show/hide table
图 1 | g00824021 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将轴组件 (12) 安装到机油泵壳体 (9) 内。
Show/hide table
图 2 | g00614694 |
Show/hide table
图 3 | g00614689 |
- 将轴组件 (11) 安装到机油泵壳体 (9) 内。
- 将机油泵壳 (9) 放置到机油泵壳组件 (7) 上,然后安装螺栓 (10) 。
- 将驱动齿轮 (8) 压到轴组件 (11) 上,直到驱动齿轮 (8) 与轴组件 (11) 的端部齐平。
Show/hide table
图 4 | g00614683 |
- 安装机油泵轴 (6) 。 使用工具 (A) ,将轴承安装到惰轮 (5) 中。 安装轴承,使惰轮 (5) 的轮毂螺栓面和轴承间的距离为 0.75 ± 0.25 mm (0.030 ± 0.010 in)。
- 将惰轮 (5) 安装到机油泵轴 (6) 上。 安装垫圈 (4) 和螺栓 (3) 。 将螺栓 (3) 上紧到 70 ± 15 N·m (52 ± 11 lb ft)。
Show/hide table
图 5 | g00614677 |
- 检查用于吸油管 (2) 的管组件的密封垫的状况。 如果密封垫损坏,则更换密封垫。 安装吸油管 (2) 的密封垫和管组件。
Show/hide table
图 6 | g00614664 |
- 检查出口弯头 (1) 内所用 O 形密封圈的状态。 如果 O 形密封圈损坏,更换 O 形密封圈。 安装 O 形密封圈和出口弯头 (1) 。
End By: 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
3512B Marine Auxiliary Engine Injector Solenoids
3114, 3116 and 3126 Engines Noise Coming from Cylinder
3114, 3116 and 3126 Engines Mechanical Noise (Knock) in Engine
3114, 3116 and 3126 Engines Low Power
3114, 3116 and 3126 Engines Low Engine Oil Pressure
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 330 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
3126B Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
G3612 and G3616 Engines Cylinder Head - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
G3304 and G3306 Engines Valve Mechanism
G3304 and G3306 Engines Cylinder Head Valves
3126B Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3126B Engines for Caterpillar Built Machines Engine Oil Cooler - Install
3126B Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove
SR4B Generators Insulation - Test
3034 Industrial Engine Fuel Lines
3126B Engines for Caterpillar Built Machines Engine Oil Filter Base - Install
3126B Engines for Caterpillar Built Machines Engine Oil Filter Base - Disassemble
3126B Truck Engine Unit Injector - Install
C9 Engine For Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3126B Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
3114, 3116 and 3126 Engines Soot in Inlet Manifold