Exhaust Manifold - Remove and Install
拆卸步骤
开始:
- 拆卸后冷器。 参考拆解与组装, "后冷器 - 拆卸和安装"。
- 拆卸进气歧管。 参考拆解与组装, "进气歧管 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和部件使用说明降低。 |
注: 拆卸排气歧管时没必要先拆下进气歧管。 但是步骤会更复杂一些。 拆卸排气歧管前必须先拆下后冷器。
- 从加热罩 (2) 上拆卸螺栓 (1) 和垫圈。
Show/hide table
图 1 | g00616579 |
- 拆卸加热罩 (2) 。
- 拆卸固定排气歧管与涡轮增压器弯管的螺母 (3) 和螺栓。 取下密封垫。
Show/hide table
图 2 | g00616580 |
- 拆卸固定排气歧管与缸盖的螺栓 (4) 、螺母和垫圈。 拆卸密封垫 (5) 。
Show/hide table
图 3 | g00616613 |
- 将适当起吊设备连在排气歧管 (6) 上。
3508B 发动机排气歧管 (6) 的重量约为78 kg (170 lb)。 3512B 发动机排气歧管 (6) 的重量约为125 kg (275 lb)。 3516B 发动机排气歧管 (6) 的重量约为154 kg (340 lb)。
Show/hide table
图 4 | g00616615 |
- 从发动机上提升排气歧管 (6) 。
安装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 4C-5597     | 防咬合剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和部件使用说明降低。 |
- 将适当起吊设备连在排气歧管 (6) 上。
3508B 发动机排气歧管 (6) 的重量约为78 kg (170 lb)。 3512B 发动机排气歧管 (6) 的重量约为125 kg (275 lb)。 3516B 发动机排气歧管 (6) 的重量约为154 kg (340 lb)。
Show/hide table
图 5 | g00616615 |
- 将排气歧管 (6) 连接到发动机上。
- 为排气歧管和缸盖间的接头安装新密封垫 (5) 。 用工具 (A) 操作螺栓 (4) 。 安装与排气歧管和缸盖相连的螺栓 (4) 、螺母和垫圈。 拧紧螺栓 (4) 至扭矩为55 ± 5 N·m (41 ± 4 lb ft)。
Show/hide table
图 6 | g00616613 |
- 在排气歧管和涡轮增压器弯管间的接头上安装一个新密封垫。 用工具 (A) 操作螺栓 (3) 。 安装螺栓 (3) 和螺母。 以对角的方式同时拧紧螺栓 (3) 至扭矩为55 ± 5 N•m (41 ± 4 lb ft)。
Show/hide table
图 7 | g00616580 |
- 安装加热罩 (2) 。
Show/hide table
图 8 | g00616579 |
- 为加热护罩 (2) 安装螺栓 (1) 和垫圈。
End By:
- 安装进气歧管。 参考 拆解与组装, "进气歧管 - 拆卸和安装"。
- 安装后冷器。 参考 拆解与组装, "后冷器 - 拆卸和安装"。
Caterpillar Information System:
3114, 3116 and 3126 Engines Excessive Fuel Consumption
3512B Marine Auxiliary Engines Fuel Injector - Install
G3304 and G3306 Engines Engine Design
3126B Marine Engine Glossary of Electronic Control Terms
3512B Marine Auxiliary Engines Fuel Injector - Remove
3114, 3116 and 3126 Engines Excessive Engine Oil Consumption
G3612 and G3616 Engines Water Lines - Remove and Install
G3612 and G3616 Engines Water Manifold - Remove and Install
3612 and 3616 Engines Water Pump Seal - Install
3500B Engines Rocker Shaft - Assemble
3500B Engines Rocker Shaft - Disassemble
3612 and 3616 Engines Water Pump Seal - Remove
3512B Marine Auxiliary Engines Cylinder Head - Remove
3500B Locomotive Engines MID 036 - CID 0011 - FMI 05 Injector Cylinder 11 open circuit
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Accessory Drive (Front) - Remove
G3304 and G3306 Engines Engine Design
Installation and Initial Start-Up Procedure for G3516B and G3520B Engines{1000} Installation and Initial Start-Up Procedure for G3516B and G3520B Engines{1000}
3500B Locomotive Engines MID 036 - CID 0248 - FMI 02 Invalid CAT Data Link data
3114, 3116 and 3126 Engines Excessive Valve Lash
3500B Locomotive Engines MID 036 - CID 0339 - FMI 05 Engine Pre-lube Pressure Switch open circuit
3500B Locomotive Engines MID 036 - CID 0444 - FMI 05 Start Relay open circuit
3500B Locomotive Engines Engine Cranks but Will Not Start
3524B Engines for Off-Highway Trucks Engine Misfires, Runs Rough or Is Unstable
3516B Engine for Caterpillar Built Machines ECM Will Not Accept Factory Passwords