Exhaust Manifold Shield - Remove and Install
拆卸步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
小心处理护罩。 不要撕破热护罩内的不锈钢箔。 |
- 剪切将护罩组件固定在一起的不锈钢丝。
Show/hide table
 | |
| 图 1 | g01285793 |
- 拆下将护罩组件 (1) 固定到缸盖和后冷器上的螺栓，然后拆下护罩组件 (1) 。
- 卸下护罩组件 (2) 。
- 拆下将护罩组件 (3) 固定到涡轮增压器上的螺栓，然后拆下护罩组件 (3) 。
Show/hide table
| 注意 |
|---|
不要使用易燃的液体来清洁防热罩内的不锈钢箔。 只使用水和清洁剂。 当发动机温度升高时，易燃液体可能浸透绝缘材料并导致着火。 |
安装步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
小心处理护罩。 不要撕破热护罩内的不锈钢箔。 |
- 将护罩组件 (3) 放好，安装螺栓以将护罩组件 (3) 固定到涡轮增压器上。
Show/hide table
| | |
| 图 2 | g01285793 |
- 卸下护罩组件 (2) 。
- 将护罩组件 (1) 放好，安装螺栓以将护罩组件 (1) 固定到缸盖和后冷器。
- 使用不锈钢丝将护罩组件固定到一起。
Caterpillar Information System:
3500B Engines Water Pump - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Aftercooler
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Refill Capacities
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Lubricant Viscosities
3500B Engines Water Temperature Regulators - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5240, 9Q-5241, 9Q-5242, 9Q-5250, 9Q-5253, 9Q-5265, 9Q-5266, 9Q-5392, 9Q-5393, 9Q-5478, 9Q-5504, 9Q-5621, 9Q-5643, 9Q-5651, 9Q-5709, 9Q-5718, 9Q-5723, 9Q-5724, 9Q-5725, 9Q-5726, 9Q-5731, 9Q-5747, 9Q-5780, 9Q-5792, 9 Final Drive Oil
CIPI UNDERCARRIAGE Arrangements: 3Q-6662; 6Z-7861, 7885, 7947, 7957, 7999; 9Q-5044, 5065, 5082, 5090, 5093, 5115, 5118, 5126, 5135, 5141, 5168, 5175, 5206, 5255, 5259, 5268, 5412, 5436, 5464, 5514, 5617, 5618, 5716, 5741, 5742, 5758, 5826, 5831, 5846 Hydraulic Oil
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Torques for Bolts on Major Components
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Standard Torque for Inch Fasteners
CIPI UNDERCARRIAGE Arrangements: 166-7047, 177-3011, 177-3553, 177-4279, 200-2995, 200-4060, 204-0808, 212-6225, 213-8653, 215-7227, 218-2237, 231-5143, 3Q-6638, 3Q-6641, 6Z-7749, 6Z-7751, 6Z-7857, 6Z-7890, 6Z-7926, 6Z-7938, 6Z-7992, 9Q-5034, 9Q-5042 Standard Torque for Metric Fasteners
143H and 163H Motor Graders General Torque Information
Guidelines for the Use of Clean Out Filters for the Hydraulic Oil System and for the Power Train Oil System{3067, 5068} Guidelines for the Use of Clean Out Filters for the Hydraulic Oil System and for the Power Train Oil System{3067, 5068}
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Air Inlet Heater
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3500B Engines Water Pump (Separate Circuit Aftercooler) - Remove
3500B Engines Water Pump (Separate Circuit Aftercooler) - Install
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Pump Housing - Assemble
3500B Engines Water Pump (Separate Circuit Aftercooler) - Disassemble
3500B Engines Water Pump (Separate Circuit Aftercooler) - Assemble
3500B Engines Auxiliary Water Pump - Remove - Auxiliary Sea Water Pump
3500B Marine Engines Injector Solenoids
3500B Engines Auxiliary Water Pump - Install - Auxiliary Sea Water Pump
Electronic Modular Control Panel II+ (EMCP II+) AC Factory Calibration Setpoint Programming OP5-2
Electronic Modular Control Panel II+ (EMCP II+) Parallel Setpoint Programming OP5-3