Gear Group (Front) - Install
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 1P-0510 | 起子总成 | 1 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将轴 (5) 定位到缸体上后安装螺栓 (4)。 用
55 ± 10 N·m (41 ± 7 lb ft) 的扭矩拧紧螺栓 (4)。采用以下顺序上紧轴的螺栓 (4)。 参看图 2 的螺栓编号。 ... 1、3、4、5、2、1、2、3、4、5、1
- 安装止推垫圈 (6)，使油槽侧面向惰轮。
Show/hide table
图 3 g00577286 - 冷却轴承。 利用工具 (A) 和适当的压具将轴承安装到惰轮 (3) 内。 将轴承安装到
0.38 ± 0.25 mm (0.015 ± 0.010 in) 的深度。Show/hide table
图 4 g00577213 - 将干净的机油涂抹到轴和惰轮 (3) 的内表面上。 将惰轮 (3) 安装到轴上。 安装板 (2) 和螺栓 (1)。
Show/hide table
| |
| 图 1 | g00577251 |
Show/hide table
| |
| 图 2 | g00537659 |
结束:
- 安装凸轮轴。 请参阅拆解和组装, "凸轮轴 - 安装"。
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Front) - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type V) - Disassemble
365B and 365B Series II Excavators Hydraulic System Swivel
3412E, C30 and C32 Marine Engines Housing (Front) - Install
3176C and 3196 Engines for Caterpillar Built Machines Electronic Unit Injector - Test
C18 Marine Generator Set Rotating Rectifier - Check
SR4 HV and SR4B HV Generators Space Heater - Check
SR4 HV and SR4B HV Generators Electrical Connections - Check
SR4 HV and SR4B HV Generators Stator Lead - Check
SR4 HV and SR4B HV Generators Generator Set Vibration - Inspect
SR4 HV and SR4B HV Generators Generator Load - Check
SR4 HV and SR4B HV Generators Power Factor - Check
3176B Industrial Engine Model View Illustrations
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
G3500 Engines Crankshaft - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Governor
3054, 3054B and 3056 Marine Engines Marine Transmission Oil
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove
G3500 Engines Crankshaft - Install
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Injection Control Linkage
3126 Truck Engine (Military) Exhaust Brake
3612 and 3616 Engines Exhaust Manifold
3176C and 3196 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect