Rear Axle - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-7498     | 支撑支座组件     | 2     |
B     | 1U-7505     | 液压千斤顶     | 1     |
C     | 222-3123     | 渗透油     | -     |
- 用适当的链条将后车桥组件 (9) 连接到工具 (B) 上。 后车桥组件 (9) 的重量约为 545 kg (1200 lb)。
Show/hide table
图 1 | g02920301 |
Show/hide table
图 2 | g02920316 |
Show/hide table
图 3 | g02920538 |
- 安装后车桥组件 (9) 。 将阀体 (14) 放置到位,然后安装螺栓 (13) 。 对于另一侧,重复本步骤。
- 安装罩盖 (12) 。 对于另一侧,重复本步骤。
Show/hide table
图 4 | g03110716 |
- 将软管组件 (11) 和 (10) 连接至后车桥组件 (9) 。
Show/hide table
图 5 | g02920298 |
- 将软管组件 (8) 连接到后车桥组件 (9) 上。
Show/hide table
图 6 | g02920296 |
- 安装新螺栓 (7) 以连接后驱动轴 (6) 。 拧紧螺栓 (7) 至 28 ± 7 N·m (21 ± 5 lb ft) 的扭矩。
Show/hide table
图 7 | g02920276 |
- 连接停车制动器电缆组件 (4) 。 安装销 (5) 。 安装夹子 (3) 。
Show/hide table
图 8 | g02920257 |
- 将后轮胎和轮缘 (2) 固定到合适的电力车上。 后轮胎和轮缘 (2) 的重量约为 113 kg (250 lb)。 使用适当的电力车以将后轮胎和轮缘 (2) 定位到机器上。
Show/hide table
图 9 | g02920158 |
- 将一滴工具 (C) 涂抹到凸缘螺母 (1) 的螺纹上。 安装凸缘螺母 (1) 。
注: 确保双头螺栓和凸缘螺母 (1) 都清洁和干燥。
- 对机器的另一侧重复步骤 8 至 9。
- 提升机器后部。 拆下工具 (A) 。 将机器降至地面上。
Show/hide table
图 10 | g03094858 |
- 拧紧凸缘螺母 (1) 至 190 ± 10 N·m (140 ± 7 lb ft) 的扭矩。 将凸缘螺母 (1) 再转动 60 度 ± 5 度。 对机器的另一侧重复此步骤。
Show/hide table
图 11 | g01260063 |
- 排出制动器的空气。 参考测试和调整手册, "制动系统空气 - 排放"。
Caterpillar Information System:
C3.8 Engines for Caterpillar Built Machines Electrical System
Signature Tests for Certain 797B Off-Highway Trucks{7601} Signature Tests for Certain 797B Off-Highway Trucks{7601}
Signature Tests for Certain 789B And 793B Off-Highway Trucks{7601} Signature Tests for Certain 789B And 793B Off-Highway Trucks{7601}
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Relief Valve (Charge) - Test and Adjust
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Power Train Rear Axle - Remove
C175-16 Engines for Off-Highway Truck/Tractors Coolant Pressure Is Low
416F, 420F, 422F, 428F, 430F, 432F, 434F, 444F and 450F Backhoe Loaders Monitoring System Module - Configure
420F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Transmission - Standard Shift
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Power Train Tire and Rim (Rear) - Remove and Install
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Relief Valve (Steering) - Test
C175-16 Locomotive Engine Electronic Service Tool Does Not Communicate
2012/03/07 VIMSpc 2011A Update Utility Is Now Available for Certain CAT Products {7601}
3516B Generator Set Engines with Dynamic Gas Blending Symptom Troubleshooting
586C LRC Site Prep Tractor Indicators and Gauges - Test
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Power Train Parking Brake - Remove and Install
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Oil Contains Fuel
770G and 772G OEM Off-Highway Truck Chassis Specifications
CP56B, CP68B, CS56B, CS66B and CS68B Vibratory Soil Compactors Machine Systems Relief Valve (Main, Vibratory) - Test and Adjust
2012/07/11 A New Rework Procedure Improves Gerotor Motor and Control Valve for the Circle Drive on Certain Motor Graders {5051, 5082}
C175-16 Locomotive Engine Exhaust Has Excessive Black Smoke
CB44B, CB54B, CD44B and CD54B Vibratory Asphalt Compactors Machine Electronic Control System MID 039 - CID 0332 - FMI 12
C18 Generator Sets Engine Speed/Timing Sensor - Clean/Inspect
2012/03/05 New Generator Belt and Idler Pulleys Now Used {4450}
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Safety Messages