Lift Arms - Remove and Install - Single Tilt
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 8S-7640     | 台架     | 1     |
8S-7631 | 管     | 1     | |
8S-8048 | 鞍座     | 1     | |
8S-7615 | 触针     | 1     | |
B     | 1U-9200     | 操纵杆滚轮举倾机构     | 1     |
C     | 1P-1832     | 适配器     | 1     |
9S-5565 | 拔销器套筒组件     | 1     | |
126-8928 | 硬垫圈     | 1     | |
9U-6833 | 螺母     | 1     | |
5P-4776 | 拉拔器螺柱     | 1     | |
350-7768 | 电动液压泵总成(115 V)     | 1     | |
350-7769 | 电动液压泵总成(230 V)     | 1     | |
6V-3160 | 双作用油缸     | 1     |
开始:
- 拆下倾斜油缸。
- 拆下铲斗。
Show/hide table
配备锁止阀的油缸即使在软管拆卸后也会长时间保持高压状态。 如果拆卸锁止阀或解体油缸之前没有释放所有压力,则可能会导致人身伤亡。 拆卸锁止阀或解体油缸之前确保释放所有压力。 |
Show/hide table
当您使用液压油缸和拉拔器螺柱时,务必确保拉拔器螺柱的额定容量达到或超过液压油缸的额定容量。 如果拉拔器螺柱未达到或超过液压油缸的额定容量,拉拔器螺柱可能突然发生故障。 拉拔器螺柱的突然故障可能导致人身伤亡。 |
- 使用工具 (A) 升高提升臂 (1) 。 将适当的起吊设备连接到提升油缸 (3) 的连杆端。 提升油缸 (3) 的重量约为 57 kg (125 lb)。 拆下销组件 (2) 。 使用适当的起吊设备以降下提升油缸 (3) 的连杆端,使其离开提升臂 (1) 。 对另一侧重复上述步骤。
Show/hide table
图 1 | g03024176 |
- 将软管组件 (4) 和 (5) 从机器各侧断开。
Show/hide table
图 2 | g03024517 |
- 将工具 (B) 和适当的起吊设备连接到提升臂 (1) 上。 提升臂 (1) 的重量约为 318 kg (700 lb)。
Show/hide table
图 3 | g03024557 |
- 拆下螺栓 (6) 和挡板。 由两人拆下针脚 (7) 。 销 (7) 的重量约为 24 kg (52 lb)。 拆下提升臂 (1) 。
注: 注意用于组装的垫片的数量和位置。
Show/hide table
图 4 | g03024656 |
Show/hide table
图 5 | g03025632 |
- 使用工具 (C) 拆下轴承 (8) 。
Show/hide table
图 6 | g03025957 |
Show/hide table
图 7 | g03033160 |
安装步骤
- 按与拆卸相反的顺序安装提升臂 (1) 。
Caterpillar Information System:
422F, 428F, 432F, 434F and 444F Backhoe Loaders Machine Systems Tilt Cylinder - Remove and Install - Single Tilt
CS44B and CP44B Vibratory Soil Compactors Operation Information
422F, 428F, 432F, 434F and 444F Backhoe Loaders Machine Systems Bucket Positioner Control - Remove and Install - Single Tilt
CS44B and CP44B Vibratory Soil Compactors Stopping the Engine
CS44B and CP44B Vibratory Soil Compactors Stopping the Machine
777G Off-Highway Truck Engine Supplement Rear Gear (Engine) - Remove and Install
CS44B and CP44B Vibratory Soil Compactors Engine Starting
777G Off-Highway Truck Machine Systems Slack Adjuster (Rear) - Assemble
2012/02/08 Improved 258-4142 Bus Bar Used on the 836H Landfill Compactor, 834H Wheel Dozer, and the 988H Wheel Loader {1408, 445B}
D6 Track Type Tractor Machine Systems Accumulator - Uncharged
C11 and C13 Engines Flywheel Housing Cover
3412 Generator Set Engines Atmospheric Pressure Sensor
422F, 428F, 432F, 434F and 444F Backhoe Loaders Machine Systems Lift Cylinder - Remove and Install - Single Tilt
422F, 428F, 432F, 434F and 444F Backhoe Loaders Machine Systems Hoe Bucket - Remove and Install
773G and 775G OFF-Highway Trucks Power Train Speed Sensor (Transmission) - Remove and Install
773G and 775G OFF-Highway Trucks Power Train Speed Sensor (Transmission) - Disassemble
299D and 299D XHP Compact Track Loaders and 272D and 272D XHP Skid Steer Loaders Machine Systems Tandem Drive and Axle
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Chassis Electronic Control System Event Code List
Cat® Detect Installation Guide Database Install
793F CMD Off-Highway Truck MID 161 - CID 0246 - FMI 14
793F CMD Off-Highway Truck MID 161 - CID 0296 - FMI 09
793F CMD Off-Highway Truck MID 161 - CID 0296 - FMI 14
793F CMD Off-Highway Truck MID 162 - CID 0296 - FMI 09
793F CMD Off-Highway Truck MID 162 - CID 0296 - FMI 14