Alternator Mounting
Show/hide table
 | |
| Illustration 1 | g03324897 |
Show/hide table
| Specification for 370-9315 Alternator Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | - | - | Tighten the pulley retaining nut to 110 ± 10 N·m (81 ± 7 lb ft). |
| 2 | - | - | Adjust the belt tension according to the 197-9087 Tension Chart . |
| 3 | 1 | 7E-4839 Pulley | The misalignments between the pulleys should not exceed 0.4 degrees. |
| 4 | 1 | 367-2824 Pulley As | |
| 5 | 1 | 235-2484 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. |
Show/hide table
| Specification for 197-9087 Belt Tension Chart | |||||||
| Size of Belt | Width of Belt | Gauge Reading | Gauge (Force) | Belt Tension (Frequency) "Initial" (1) |
Belt Tension (Frequency) "Used" (2) (3) |
Gauge (Frequency) | |
| Belt Tension (Force) "Initial" (1) |
Belt Tension (Force) "Used" (2) (3) |
Basic Gauge Number | Gauge Number | ||||
| 8 - RIB POLY - RIB |
27.82 mm (1.095 inch) |
800 ± 22 N (180 ± 5 lb) |
489 ± 44 N (110 ± 10 lb) |
BT-33-109 | 98 ± 10 HZ | 76 ± 8 HZ | Clavis Type 14 |
| Do not use the belt tension chart for belts with tensioners that are spring loaded. | |||||||
| Measure the tension of the belt that is farthest from the engine. | |||||||
Show/hide table
| ( 1 ) | Belt tension "lnitial" is for a new belt. |
| ( 2 ) | Belt tension "Used" is for a belt that has operated for 30 minutes or more of operation at the rated speed. |
| ( 3 ) | If a belt falls below the "Used" belt tension, the belt should be tightened again to the high side of the "Used" belt tension. |
Caterpillar Information System:
CP56B, CP68B, CS56B and CS68B Vibratory Soil Compactors Propel System Control Valve (Shift)
3516B and 3516C Engines for 789D Off-Highway Trucks Air Lines - Aftercooler
CP74B, CS74B, CS78B and CS79B Vibratory Soil Compactors Propel System Drum Installation Group
R1600H Load Haul Dump Power Train MID 081 - CID 0590 - FMI 09
2012/01/27 New Software Is Now Available for the Cat® Object Detection System (Cat Detect) Used on Certain Off-Highway Trucks {7347, 7348}
259D, 279D, 289D, 299D, 299D XHP, 299D2 and 299D2 XHP Compact Track Loaders, 257D, 277D, 287D, 297D, 297D XHP, 297D2 and 297D2 XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D, 272D XHP, 272D2 and 272D2 XHP Skid Steer Loaders Lift Cylinder
R1600H Load Haul Dump Power Train General Information
988K XE Wheel Loader Engine Mounts - Inspect
Product Identification Numbers (PIN) Location Guide Articulated Truck
2012/02/21 The Painted Interior Cab Color Is Now Black on Certain M and M Series 2 Motor Graders {7301, 7559}
PL87 Pipelayer Power Train Relief Valve (Torque Converter Inlet) Pressure - Test
PL87 Pipelayer Power Train Transmission Lubrication Oil Pressure - Test
C7.1 Engines For Caterpillar Built Machines Self-Diagnostics
CP54B, CS54B and CS64B Vibratory Soil Compactors Propel System Axle Mounting
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Flywheel
553C, 563C and 573C Wheel Feller Bunchers IQAN Monitoring ; Control System Tree Counter Display
3516E Engines for Caterpillar Built Machines Flywheel
553C, 563C and 573C Wheel Feller Bunchers IQAN Monitoring ; Control System Connector Locations
272D and 272D XHP Skid Steer Loaders and 299D and 299D XHP Compact Track Loaders Fuel System Filter (In-Line) - Replace
C15 and C18 Engines for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
272D and 272D XHP Skid Steer Loaders and 299D and 299D XHP Compact Track Loaders Engine Crankcase Breather - Replace - and PCV Valve Check
Product Identification Numbers (PIN) Location Guide Excavator (Mini)
CS54B, CS64B and CP54B Vibratory Soil Compactor Propel System Drum Drive Group
C2.6 and C3.3B Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove and Install - C3.3B and C2.6