Bogie
Show/hide table
 | |
| Illustration 1 | g02475956 |
Rear right view | |
Show/hide table
| Specification for 332-1821 Bogie Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 1B-4443 Nut | Torque to 644 ± 25 N·m (475 ± 18 lb ft). Again torque the nuts until the cotter pin can be inserted through the bolts and the nuts. |
| 2 | 2 | 312-7705 Bearing Adjuster | Torque to 240 ± 25 N·m (177 ± 18 lb ft). Bearing adjusters to be flush within 0.0 to 0.5 mm (0.00 to 0.02 inch) to spindle assembly and or motor mount after tightening. |
| 3 | 10 | 1K-7019 Shim | As required use the shims to adjust the clearance. Thickness is 0.51 mm (0.020 inch). |
| 4 | 4 | 6R-1554 Bearing As | Apply green Loctite 609 to the bearing assemblies. |
| 5 | 2 | 4D-3882 Bearing Cone | Lubricate and pack the bearing cones and the bearing cups with the medium pressure lithium grease or black 5P-0960 Grease Cartridge. |
| 6 | 2 | 006-7231 Bearing Cup | |
| 7 | 1 | 006-8943 Nut | Use the following procedure in order to Torque the nut: 1. Torque to 280 ± 10 N·m (207 ± 7 lb ft) while turning the hub. 2. Loosen the nut by one turn, while turning the hub. 3. Again, torque the nut to 75 ± 5 N·m (55 ± 4 lb ft) 4. Continue to torque the nut until the cotter pin can be inserted through the shaft and the nut. |
| 8 | 1 | 233-9842 Hub Cap | Apply black Loctite 593 all around the hub cap to fill gap from chamfer on mating wheel assembly. |
| 9 | 1 | 061-6915 Nut | Torque to 609 ± 75 N·m (449 ± 55 lb ft). |
| 10 | 2 | 1A-4168 Nut | Torque to 609 ± 75 N·m (449 ± 55 lb ft). |
| 11 | 10 | 132-8584 Nut | Torque to 140 ± 25 N·m (103 ± 18 lb ft) |
Caterpillar Information System:
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706} 9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
725C2 Articulated Truck Seat
120M, 12M, 140M and 160M Motor Graders Machine Systems System Pressure - Release
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Transmission Planetary Troubleshooting
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Piston Pump (Brake) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Torque Converter Troubleshooting
797B Off-Highway Truck Gear Pump (Brake, Rear Axle Lubrication) - Remove and Install
AP1055E and BG1055E Asphalt Pavers Propel System Final Drive Planetary (Mobil-Trac)
C7.1 Engines For Caterpillar Built Machines Cooling Fan Control - Test
AP1055E and BG1055E Asphalt Pavers Machine Systems Tow Arm
2011/04/07 An Improved Plate Assembly is Now Used on the 797F Off-Highway Truck {7510, 7540}
Do Not Use Loctite Moly Paste 51049 on Critical Fasteners{0645} Do Not Use Loctite Moly Paste 51049 on Critical Fasteners{0645}
C7.1 Engines For Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Hydraulic Oil Contamination - Test
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Flame Detection Temperature Sensor - Remove and Install
323-1146 C-175 Engine Lifting Bracket{0599, 0629, 0701, 1000, 1122} 323-1146 C-175 Engine Lifting Bracket{0599, 0629, 0701, 1000, 1122}
C18 Generator Set Engine Speed/Timing Sensor - Clean/Inspect
C13, C15, and C18 Tier 4 Interim Engines Shutdown - Test
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Fan Drive System - Test
AP1055E and BG1055E Asphalt Pavers Machine Systems Position Sensor (Paddle)
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Seat
2011/05/09 Additional Front Signal Lamps Are in Production on Certain Off-Highway Trucks {1430, 1432}
Comfort Series Seat For Caterpillar Machines Optimized Seat Air Suspension with Air Compressor
584 and 584HD Forwarders Power Train Articulating and Oscillating Hitch