Bottom Guards (Front) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-7505     | 液压千斤顶     | 1     |
- | 大约 609.6 mm (2.00 ft) x 914.4 mm (3.00 ft) x 12.7 mm (0.50 in) 的钢板 (1)     |
1     |
Show/hide table
( 1 ) | 将钢板点焊到液压千斤顶的顶板上。 |
开始:
- 连接转向机架锁。
- 通过定位工具 (A) 和适当的支座支撑铰接端对面上的底部防护罩 (1) 。 底部防护罩 (1) 的重量约为 220 kg (485 lb)。
Show/hide table
图 1 | g02120536 |
Show/hide table
图 2 | g02120575 |
Show/hide table
不要降低机器下的底护板。 在降低过程中,如果底护板滑出千斤顶则会对人员造成伤害。 |
注: 底部防护罩 (1) 可能含有大量的岩石、泥土、油液和碎屑,从而会增加许多额外的重量。
- 拆下螺栓 (2) 。 对机器的另一侧重复此步骤。
- 拆下螺栓 (3) 和垫圈。
- 利用工具 (A) 和适当的支座认真降下底部防护罩 (1) 。
- 拆下销 (5) 后将防护罩油缸 (4) 从底部防护罩 (1) 上断开。
Show/hide table
图 3 | g02124055 |
- 利用工具 (A) 和适当的支座将底部防护罩 (1) 升到升起位置。
Show/hide table
图 4 | g02121778 |
- 安装一个垫圈和螺栓 (3) 。 安装螺栓 (2) 。 对机器的另一侧重复此步骤。
- 通过重新定位工具 (A) 和适当的支座支撑整个底部防护罩 (1) 。
Show/hide table
图 5 | g02125113 |
Show/hide table
图 6 | g02120637 |
Show/hide table
不要降低机器下的底护板。 在降低过程中,如果底护板滑出千斤顶则会对人员造成伤害。 |
- 拆下螺栓 (3) 和垫圈。 对机器的另一侧重复此步骤。
- 拆下螺栓 (6) 。 对机器的另一侧重复此步骤。
- 利用工具 (A) 和适当的支座认真降下底部防护罩 (1) 。
- 断开软管组件 (7) 。 拆下销 (8) 。 拆下防护罩油缸 (4) 。
Show/hide table
图 7 | g02131699 |
不带液压油缸的底部防护罩
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-7505     | 液压千斤顶     | 1     |
- | 大约 609.6 mm (2 ft) x 914.4 mm (3 ft) x 12.70 mm (0.5 in) 的钢板 (1)     |
1     |
Show/hide table
( 1 ) | 将钢板点焊到液压千斤顶的顶板上。 |
- 通过定位工具 (A) 和适当的支座支撑铰接端对面上的底部防护罩 (1) 。 底部防护罩 (1) 的重量约为 220 kg (485 lb)。
Show/hide table
图 8 | g02120536 |
Show/hide table
图 9 | g02120575 |
Show/hide table
不要降低机器下的底护板。 在降低过程中,如果底护板滑出千斤顶则会对人员造成伤害。 |
注: 底部防护罩 (1) 可能含有大量的岩石、泥土、油液和碎屑,从而会增加许多额外的重量。
- 拆下螺栓 (2) 。 对机器的另一侧重复此步骤。
- 拆下螺栓 (3) 和垫圈。
- 利用工具 (A) 和适当的支座认真降下底部防护罩 (1) 。
- 将链条 (4) 从机器上断开。
Show/hide table
图 10 | g02131706 |
- 利用工具 (A) 和适当的支座将底部防护罩 (1) 升到升起位置。
Show/hide table
图 11 | g02121778 |
- 安装一个垫圈和螺栓 (3) 。 安装螺栓 (2) 。 对机器的另一侧重复此步骤。
- 通过重新定位工具 (A) 和适当的支座支撑整个底部防护罩 (1) 。
Show/hide table
图 12 | g02125113 |
Show/hide table
图 13 | g02120637 |
Show/hide table
不要降低机器下的底护板。 在降低过程中,如果底护板滑出千斤顶则会对人员造成伤害。 |
- 拆下螺栓 (3) 和垫圈。 对机器的另一侧重复此步骤。
- 拆下螺栓 (6) 和垫圈。 对机器的另一侧重复此步骤。
- 利用工具 (A) 和适当的支座认真降下底部防护罩 (1) 。
安装步骤
- 采用与拆卸程序相反的顺序安装底部防护罩 (1) 。
Caterpillar Information System:
AP555E and BG555E Asphalt Pavers Machine Systems Hydraulic Oil Contamination - Test
AP555E and BG555E Asphalt Pavers Machine Systems Machine System Troubleshooting
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1959 - FMI 04
793F Off-Highway Truck Engine Supplement Engine Oil Cooler - Remove and Install
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1959 - FMI 03
568 GF and 568 LL Forest Machine Window (Side Sliding)
AP555E and BG555E Asphalt Pavers Machine Systems Visual Inspection
AP555E and BG555E Asphalt Pavers Machine Systems Machine Preparation for Troubleshooting
797F and 797 XQ Off-Highway Trucks Engine Supplement Battery - Remove and Install
The Addition of Reinforcement Plates In Order to Repair Cracks at the Pin Joints on the Lift Arms for Certain Skid Steer Loaders and Multi Terrain Loaders{6119, 7050} The Addition of Reinforcement Plates In Order to Repair Cracks at the Pin Joints on the Lift Arms for Certain Skid Steer Loaders and Multi Terrain Loaders{6119, 7050}
621H, 623H and 627H Wheel Tractor-Scrapers Braking and Hydraulic Fan System Shuttle Valve (Brake, Hydraulic Fan)
C13, C15, and C18 Tier 4 Final Engines Fuel Priming Pump and Primary Fuel Filter - With Water Separator
120M Series 2, 120M2, 12M Series 2, 12M Series II, 140M Series 2 and 160M Series 2 Motor Graders Implement Electronic Control System MID 082 - CID 1558 - FMI 09
IT38H Integrated Toolcarrier and 938H Wheel Loader Hood Tilt
120M Series 2, 120M2, 12M Series 2, 12M Series II, 140M Series 2 and 160M Series 2 Motor Graders Implement Electronic Control System Symptom Troubleshooting
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Braking and Hydraulic Fan System Pressure Sensor (Brake Oil Accumulator)
C175-16 Locomotive Engine Temperature Sensor - Exhaust Temperature
C175-16 Locomotive Engine Temperature Sensor - Engine Coolant
349F and 352F Excavators Fuel Tank Shutoff and Drain Control
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold Shield
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Steering Direction Is Opposite of Expected Direction
14M3 Motor Grader Machine Systems Diverter Valve (Hydraulic Fan)
3524B and C175 Engines for Off-Highway Truck/Tractors Engine Oil Level Sensor
C27 and C32 Engines for Caterpillar Built Machines Flywheel Housing