Oscillating Axle (Rear) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 228-4583     | 车桥吊耳     | 2     |
注: 安装摆动轴组件之前,确保摆动轴组件和后机架的配合面均干净。
- 将后桥组件安置在后机架下面。
- 将工具 (A) 和合适的起吊设备连接到后桥组件上。 后桥组件的重量约为 1595 kg (3517 lb)。 将后桥组件抬升到后机架上。
Show/hide table
图 1 | g01210382 |
注: 当将后桥组件抬升到后机架上时,确保锁定销和耳轴支架中的螺栓孔与后机架的安装件架上的孔对正。
- 将螺栓 (19) 、 (20) 、螺母 (21) 和螺母 (24) 安装到后耳轴支架上。 拧紧螺母 (21) 和 (24) 至扭矩为 1050 ± 150 N·m (775 ± 110 lb ft)。
Show/hide table
图 2 | g01210385 |
- 安装锁紧螺母 (22) 和锁紧螺母 (23) 。
- 将两个螺栓 (17) 和两个螺母 (15) 安装至后耳轴支架上。
Show/hide table
图 3 | g01210384 |
后支架右侧 |
- 将螺母 (15) 拧紧至扭矩为 1050 ± 150 N·m (775 ± 110 lb ft)。
- 安装锁紧螺母 (16) 。
- 连接软管组件 (18) 。
- 将两个螺栓 (14) 和两个螺母 (11) 安装至后耳轴支架上。
Show/hide table
图 4 | g01210383 |
后支架左侧 |
- 将螺母 (11) 拧紧至扭矩为 1050 ± 150 N·m (775 ± 110 lb ft)。
- 安装锁紧螺母 (12) 。
- 连接软管组件 (13) 。
- 连接润滑软管组件 (10) 。
Show/hide table
图 5 | g01210381 |
- 连接润滑软管组件 (8) 。
Show/hide table
图 6 | g01210380 |
- 将螺栓 (7) 和螺栓 (9) 安装至夹子。
- 连接软管组件 (5) 和 (6) 。
Show/hide table
图 7 | g01210379 |
- 连接软管组件 (4) 。
Show/hide table
图 8 | g01210377 |
- 将左侧挡泥板 (3) 下降回相应位置。
Show/hide table
图 9 | g01210376 |
- 定位挡泥板 (1) 。 安装五个螺栓 (1) 。
Show/hide table
图 10 | g01210362 |
- 润滑后桥耳轴轴承。 参阅操作和维护手册, "后桥耳轴轴承 - 润滑"。
- 加注后差速器和终传动组件。 参阅操作和维护手册, "差速器和终传动油(带车桥机油冷却器) - 更换"或者操作和维护手册, "差速器和终传动油(不带车桥机油冷却器) - 更换"。
- 把空气从制动系统中排除出去。 请参阅系统操作、测试和调整, "制动系统空气 - 排气"。
- 检查液压油箱的油位。 请参阅操作和维护手册, "液压系统油位 – 检查"。
End By:
- 安装后驱动轴。 请参考 拆解和组装, "驱动轴(后)- 拆卸和安装"。
- 安装后轮胎和轮缘。 请参阅 拆解和组装, "轮胎和轮缘 - 安装"。
- 卸下车架转向锁。 请参阅 拆解和组装, "转向机架锁 - 拆卸和安装"。
Caterpillar Information System:
R1600G Load Haul Dump Power Train Final Drive and Wheel - Install
R1600G Load Haul Dump Power Train Final Drive and Wheel - Remove
R1600G Load Haul Dump Power Train Oscillating Axle (Rear) - Remove
R1600G Load Haul Dump Power Train Fixed Axle (Front) - Install
R1600G Load Haul Dump Power Train Fixed Axle (Front) - Remove
R1600G Load Haul Dump Power Train Tire and Rim - Install
R1600G Load Haul Dump Power Train Tire and Rim - Remove
140M Motor Grader Engine Supplement Air Compressor - Remove and Install
160M Motor Grader Machine Systems Wheel Lean Cylinder - Remove and Install
CP76 and CS76 Vibratory Compactors Propel System Pump Synchronization - Test and Adjust
797B Off-Highway Truck Braking System Oil Cooler (Fan Drive, Front Brake, Steering)
CP76 and CS76 Vibratory Compactors Propel System Parking Brake - Test
The Performance of the Air Conditioner in Certain C Series Skid Steer Loaders and Multi Terrain Loaders May Be Inadequate{7320} The Performance of the Air Conditioner in Certain C Series Skid Steer Loaders and Multi Terrain Loaders May Be Inadequate{7320}
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Drum) - Test and Replace
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Parking Brake - Check
CP76 and CS76 Vibratory Compactors Propel System Piston Motor Flushing Valve (Axle) - Test and Replace
561N Pipelayer Maintenance Interval Schedule
Multiple Registration Messages Occur with Product Link{733T, 7606} Multiple Registration Messages Occur with Product Link{733T, 7606}
Parts Stock Cylinder Head Assemblies with Rust Preventative Applied{1100} Parts Stock Cylinder Head Assemblies with Rust Preventative Applied{1100}
CP76 and CS76 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
CP76 and CS76 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M Motor Grader Piston Pump (All Wheel Drive) - Remove
3176C Engine for the R1600G and the R1700G Load Haul Dumps Cat Data Link - Test
3176C Engine for the R1600G and the R1700G Load Haul Dumps Coolant Level - Test