Bogie Axle - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
E | 252-8035 | 润滑脂 | 1 |
F | 8C-3698 | 油 | 1 |
G | - | Loctite 536 | - |
H | - | Loctite 5900 | - |
I | 1U-7086 | 套筒 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
注: 检查所有零件是否磨损或损坏。 如有必要,请更换部件。
- 使用工具 (A) 安装密封件 (5)。
Show/hide table
图 2 g01394807 - 冷却轴承外圈 (6)。 利用工具 (A) 安装轴承外圈 (6)。
Show/hide table
图 3 g01395090 - 重新放置转向架车轴 (1)。
- 降低轴承外环 (9) 的温度。 利用工具 (A) 安装轴承外圈 (9)。
- 安装轴承 (8)。
Show/hide table
图 4 g01400635 Show/hide table图 5 g01394866 - 请参阅拆解和组装, "重载双面密封 - 安装",了解重载双面密封 (10) 的安装步骤。
- 将重载双面密封(HDDF 密封件) (10) 的一半安装到壳体 (7) 上。 确保 HDDF 密封件 (10) 完全座入壳体 (7) 中。
Show/hide table
图 6 g01402400 - 将工具 (H) 涂抹到转向架车轴 (1) 上的槽中,用于密封壳体 (7)。 使用工具 (A) 将壳体 (7) 和 HDDF 密封件 (10) 安装到转向架车轴 (1) 上。
Show/hide table
图 7 g01400643 - 将 HDDF 密封件 (10) 的另一半安装到套筒 (4) 上。 确保 HDDF 密封件 (10) 完全座入套筒 (4) 中。
- 将工具 (F) 涂抹到 HDDF 密封件 (10) 的表面上。
Show/hide table
图 8 g01395122 - 使用适当的压具和工具 (A) 将套筒 (4) 安装到转向架车轴 (1) 上。
Show/hide table
图 9 g01402435 - 将转向架车轴 (1) 重新放置到适当的压具上。 使用工具 (A) 支撑套筒 (4)(未显示)。
- 使用工具 (E) 重新填充轴承 (3)。
- 使用适当的压具和工具 (I) 将轴承 (3) 压到套筒 (4) 上。 按压轴承 (3),直到轴承轻轻座入轴承外圈中。
Show/hide table
图 10 g01400646 - 拆下螺塞 (11) 以向转向架车轴 (1) 中加注
33 ± 2 mL (1.11 ± 0.07 oz) 的工具 (F)。 将工具 (G) 涂敷到螺塞 (11) 上,然后安装螺塞 (11)。Show/hide table图 11 g01392651 - 将 O 形密封圈 (2) 安装在转向架车轴 (1) 上。
Show/hide table
图 1 | g01395549 |
Caterpillar Information System:
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Bogie Axle - Disassemble
120K Motor Grader Circuit Breakers - Reset
PL61 Pipelayer Power Train Systems Graphic Color Codes
R1600G Load Haul Dump Steering System General Information
2007/08/06 A New Bush is Now Used in the Upper Cab Mount {7301}
3408E and 3412E Engines for Caterpillar Built Machines Shutdown (Ground Level) - Test
24M Motor Grader Braking and Hydraulic Fan System Diverter Valve (Brake Accumulator)
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Bogie Axle - Remove
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Idler Axle - Install
797B Off-Highway Truck Additional Messages
C18 Engine for Caterpillar Built Machines Sensor Signal (Analog, Passive) - Test
120K Motor Grader Air Dryer Desiccant - Replace
3412E Engine for Caterpillar Built Machines Speed Control - Test
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Bogie Axle - Install
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Bogie Wheel - Remove
3412E Engine for Caterpillar Built Machines Speed/Timing - Test
2007/09/10 A new Shimming Procedure for the Bodies on Large Off-Highway Trucks {7258, 7960}
12M, 140M and 160M Motor Graders Braking and Hydraulic Fan System Hydraulic Fan Speed - Test
12M, 140M and 160M Motor Graders Braking and Hydraulic Fan System Hydraulic Fan Speed - Calibrate and Adjust
2007/07/16 High Copper Reported in Routine Engine Oil Samples {1308, 1318, 1348}
Performance Issues with 725, 730, 735, 740, and 745 Articulated Trucks{1000, 3030, 3101} Performance Issues with 725, 730, 735, 740, and 745 Articulated Trucks{1000, 3030, 3101}
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
2007/07/16 A Revised Adjustment Procedure For The Boom Chain Is Now Available {6460}
2007/08/13 New Support Bracket {1351, 1355, 1361}