Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
拆卸步骤
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
Show/hide table
图 1 | g01335788 |
Show/hide table
图 2 | g01335790 |
- 按反向数字顺序松开螺栓 (2) 和 (5) 。 请参阅插图 2。
注: 这有助于防止排气歧管变形。
- 将中央螺栓 (2) 从排气歧管 (3) 上卸下。 将外螺栓 (5) 和隔套 (4) 从排气歧管 (3) 上拆下。
注: 在螺栓拆卸过程中,支撑歧管。
- 拆下排气歧管 (3) 。
- 拆下排气歧管 (1) 。
- 如有必要,将螺柱 (6) 从排气歧管 (3) 上拆下。
安装程序(侧装式排气歧管)
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (M10 × 100 mm)     |
4     |
B     | -     | Loctite 575     | 1     |
- 确保排气歧管清洁且无损坏。 如有必要,更换排气歧管。 清洁缸盖的接合面。
Show/hide table
图 3 | g01335790 |
Show/hide table
图 4 | g01335788 |
- 如有必要,将螺柱 (6) 安装到排气歧管 (3) 上。 拧紧螺柱至扭矩为 18 N·m (13 lb ft)。
- 将工具 (A) 安装到缸盖的位置 (X) 。 请参阅插图 3。
- 将两个新排气歧管密封垫 (1) 安置到工具 (A) 上。
注: 确保 TOP 字样朝向外部和上方。
- 对准排气歧管 (3) 与工具 (A) 。 将排气歧管安装到缸盖上。
- 如果螺栓 (2) 和 (5) 之前使用过,应该彻底清洁这些螺栓。 应将工具 (B) 涂覆到螺栓的前两圈螺纹上。
注: 请勿将工具 (B) 涂覆到新螺栓上。
- 安装螺栓 (2) 并用手拧紧。 安装螺栓 (5) 和隔套 (4) ,用手拧紧。
- 拆下工具 (A) 。 安装其余的螺栓 (2) ,用手拧紧。 安装其余的螺栓 (5) 和隔套 (4) ,用手拧紧。
- 拧紧螺栓 (2) 和 (5) 至扭矩为 44 N·m (32 lb ft)。 按照图 3 中所示的顺序拧紧螺栓。
End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Wastegate Solenoid - Remove and Install
C6.6 Engines for Caterpillar Built Machines Turbocharger - Install - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Turbocharger - Install - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Turbocharger - Assemble
C6.6 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C6.6 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C6.6 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
EquipmentManager Dealer Administrator Manual Major Repair
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install