Parking Brake - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 2P-8312     | 挡圈钳     | 1     |
B     | 8C-8422     | 密封胶     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 安装 O 形密封圈 (24) 。
Show/hide table
图 1 | g01363355 |
- 将密封件 (23) 安装到压力传感器 (16) 上。
Show/hide table
图 2 | g01990357 |
- 确保所有的 O 形密封圈没有切割或其他损坏。 安装 O 形密封圈 (22) 、 (21) 、 (20) 、 (19) 和 (18) 。
Show/hide table
图 3 | g01363336 |
- 使用要密封的润滑剂稍稍润滑 O 形密封圈。
- 检查制动器歧管是否清洁,有无碎屑。
Show/hide table
图 4 | g01363332 |
- 使电磁阀保持 (17) 竖直并将电磁阀 (17) 安装到孔中。 需要缓缓地施加压力以使电磁阀 (17) 座入孔中。
- 安装固定支架和六角螺栓。 慢慢地拧紧六角螺栓,直到电磁阀 (17) 完全座入。 拧紧六角螺栓至扭矩为 12 ± 3 N·m (106 ± 275 lb in)。
- 安装压力传感器 (16) 。 拧紧压力传感器 (16) 至扭矩为 60 ± 6 N·m (44 ± 4 lb ft)。
- 安装定位销 (15) 。 安装盘 (12) 和板 (13) 。 安装轮毂 (14) 。
Show/hide table
图 5 | g01612233 |
- 使用工具 (A) 以便安装挡圈 (14A) (未显示)。
- 将工具 (B) 涂抹到配合面上。 需要两个人来安装壳体 (11) 。
Show/hide table
图 6 | g01363308 |
- 安装螺栓 (10) 。 将螺栓 (10) 上紧到 55 ± 10 N·m (41 ± 7 lb ft) 的扭矩。
Show/hide table
图 7 | g01363295 |
- 安装密封件 (9) 。
Show/hide table
图 8 | g01363292 |
- 安装活塞 (8) 。 安装弹簧盘 (7) 。 安装 O 形密封圈 (6) 。
Show/hide table
图 9 | g01363286 |
- 安装唇形密封 (5) 。
Show/hide table
图 10 | g01363281 |
- 安装弹簧板 (4) 。 安装螺栓 (3) 。 拧紧螺栓 (3) 至 100 ± 20 N·m (74 ± 15 lb ft) 的扭矩。
Show/hide table
图 11 | g01363175 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 连接线束组件 (2) 。 安装轭 (1) 。
Show/hide table
图 12 | g01363168 |
- 加注变速箱。 请参阅操作和保养手册, "变速箱和差速器用油 - 更换"。
End By: 安装传动轴。 请参考 拆解和装配, "传动轴 - 拆卸和安装"。
Caterpillar Information System:
16M Motor Grader Power Train Parking Brake - Remove
AP655D and BG655D Asphalt Pavers Access Doors and Covers
AccuGrade® Grade Control System - CD700 Laser Guidance System
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems Gear Pump (Charge) - Install - High Flow
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems Gear Pump (Charge) - Remove - High Flow
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0262 - FMI 04
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0262 - FMI 03
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0041 - FMI 04
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0041 - FMI 03
2007/04/30 A New Seal Kit is Available for the Hydraulic Gear Motor on the Rear Axle Cooling Fan {1365, 1375, 3016, 5061}
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 039 - CID 0262 - FMI 04
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 039 - CID 0262 - FMI 03
2007/04/16 Change to the ROPS/FOPS Film {7405, 7557}
CB1.7 and CB1.8 Utility Compactors Hydraulic Tank Breather - Clean
AP655D Asphalt Paver Machine Systems Hydraulic Filter (Suction Return) - Remove and Install
992K Wheel Loader and 854K Wheel Dozer Machine Systems Governor Pedal
247B and 257B Multi Terrain Loaders Machine Systems Pilot System Pressure - Test
AP555E and BG555E Asphalt Pavers Machine Systems Hydraulic Cylinder (Screed Hoist) - Remove and Install
AP655D and BG655D Asphalt Pavers Machine Systems Piston Pump Neutral (Auger Conveyor and Drag Conveyor) - Test and Adjust
C9.3 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install - Rail
992K Wheel Loader and 854K Wheel Dozer Machine Systems Position Sensor (Throttle)
AP655D Asphalt Paver Machine Systems Control Valve (Auxiliary) - Remove
AP555E and BG555E Asphalt Pavers Machine Systems Control Valve (Auxiliary) - Disassemble
AP555E and BG555E Asphalt Pavers Machine Systems Control Valve (Auxiliary) - Assemble