Rear Wheel, Bearing, and Duo-Cone Seal - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7576     | 连杆支架     | 2     |
1U-9200 | 操纵杆滚轮起重机     | 1     | |
138-7574 | 连杆支架     | 1     | |
C     | 9U-5691     | Duo-Cone 密封件安装器组件     | 1     |
D     | 285-8787     | Duo-Cone 密封件安装器组件     | 1     |
E     | 7H-1680     | 润滑手动泵     | 1     |
F     | 8T-0447     | 游标卡尺     | 1     |
G     | 6V-2012     | 深度测微计     | 1     |
H     | 9S-3263     | 螺纹锁固胶     | -     |
- 安装 O 形密封圈和挡圈 (15) 。
Show/hide table
图 1 | g01337746 |
Show/hide table
图 2 | g01337747 |
- 利用工具 (C) 安装 Duo-Cone 密封件 (12) 。 请参阅拆解和组装, "Duo-Cone 密封件 - 安装"。
- 使用工具 (D) 安装 Duo-Cone 密封件 (13) 。 请参阅拆解和组装, "Duo-Cone 密封件 - 安装"。
- 安装轴承内圈 (14) 。
Show/hide table
图 3 | g01337749 |
- 利用工具 (D) 安装 Duo-Cone 密封 (11) 。 请参阅拆解和组装, "Duo-Cone 密封件 - 安装"。
Show/hide table
图 4 | g01337948 |
- 冷却轴承外圈 (8) 。 安装轴承外圈 (8) 。
- 安装 O 形密封圈和密封件挡圈 (10) 。 安装螺栓 (9) 。
- 利用工具 (C) 安装 Duo-Cone 密封 (7) 。 请参阅拆解和组装, "Duo-Cone 密封件 - 安装"。
Show/hide table
图 5 | g01337950 |
- 定位车轮组件 (1) 。 车轮组件 (1) 的重量约为 544 kg (1200 lb)。
Show/hide table
图 6 | g01337127 |
- 需要两个人一起安装轴承内圈 (6) 。 轴承内圈 (6) 的重量约为 25 kg (55 lb)。
Show/hide table
图 7 | g01326244 |
- 由两人安装轮毂 (5) 。 轮毂 (5) 的重量约为 36 kg (80 lb)。
Show/hide table
图 8 | g01326199 |
- 断开软管组件 (16) 。 在软管组件 (16) 上加装管塞,并在接头上加装盖。
Show/hide table
图 9 | g01337958 |
注: 需要断开工具 (A) 和适当的起吊设备才能转动车轮组件。 无论何时拆卸密封件挡圈 (10) 和螺栓 (9) 时,都必须固定工具 (A) 和适当的起吊设备。 请参阅插图 4。
- 将工具 (E) 固定到位置 (X) 。 利用工具 (E) 松开停车制动器。 不要在停车制动器上施加超过 4137 kPa (600 psi) 的作用力。
- 利用下述步骤确定需要安装的垫片 (4) 的正确数量。
- 用工具 (F) 测量护圈 (3) 的厚度。 记录该尺寸。
- 安装护圈 (3) 以及在护圈 (3) 上等距离分布的四条螺栓。 此时不要安装垫片 (4) 。 将 4 个螺栓上紧到 140 N·m (103 lb ft) 的扭矩。 松开四条螺栓。 将 4 个螺栓上紧到 70 N·m (52 lb ft) 的扭矩。
- 拆下工具 (A) 以便将车轮转动两整圈。 将 4 个螺栓上紧到 70 N·m (52 lb ft) 的扭矩。
- 转动车轮两整圈。
- 将 4 个螺栓上紧到 70 N·m (52 lb ft) 的扭矩。
- 用工具 (G) 测量护圈 (3) 外侧到车桥壳体的距离。 利用护圈 (3) 上两个相对的孔执行该测量。 求两次测量的平均值并记录该尺寸。
- 用步骤 14.f 中记录的尺寸减去步骤 14.a 中记录的尺寸。 将此尺寸加上 0.23 + 0.00 - 0.05 mm (0.009 + 0.000 - 0.002 in)。
Show/hide table
图 10 | g01338046 |
Show/hide table
图 11 | g01338052 |
- 固定工具 (A) 。 拆下四条螺栓和护圈 (3) 。 安装垫片 (4) ,总厚度为步骤 14.g 中确定的尺寸。
- 将工具 (H) 涂抹到螺栓 (2) 的螺纹上。
Show/hide table
图 12 | g01326197 |
- 安装将垫片 (4) 固定到车桥壳体上的护圈 (3) 和螺栓 (2) 。 用 22 ± 6 N·m (16 ± 4 lb ft) 的扭矩拧紧螺栓 (2) 。 丢弃不能上紧到此扭矩的全部螺栓。 重新拧紧螺栓 (2) 到扭矩 125 ± 20 N·m (92 ± 15 lb ft)。 将螺栓 (2) 上紧到 270 ± 40 N·m (199 ± 30 lb ft) 的最终扭矩。
- 向液压油箱注油。 请参阅操作和保养手册, "举倾机构和制动器油箱油 - 更换"。
End By:
- 安装后轮胎和轮辋。 请参阅 拆解和组装, "轮胎和轮辋(后)- 安装"。
- 安装终传动。 请参阅 拆解和组装, "终传动 - 安装"。
Caterpillar Information System:
773F Off-Highway Truck and 775F Quarry Truck Power Train Rear Wheel, Bearing, and Duo-Cone Seal - Remove
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Engine Wiring Information
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Sensors and Electrical Connectors
2014/06/03 New Water Pump, Water Temperature Regulator and Bypass Tube {1355, 1361}
R1700G Load Haul Dump Caterpillar Monitoring System
R2900G Load Haul Dump Machine Systems Bucket Control Safety Pins - Remove and Install
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Machine Systems Front Frame from Rear Frame - Separate
3126B Engine for Caterpillar Built Machines Injection Actuation Pressure Sensor - Test
450E Backhoe Loader Engine Starting with Starting Aid
777D and 777E Off-Highway Truck Air System and Brakes Relief Valve (Brake Oil Cooler) - Test and Adjust
RM-300 Reclaimer Mixer Machine Systems Water and Emulsion Lines
777D and 777E Off-Highway Truck Air System and Brakes Brake Oil Overheating Troubleshooting
777D and 777E Off-Highway Truck Air System and Brakes Air System
14M Motor Grader Engine Supplement Alternator - Remove and Install
777D and 777E Off-Highway Truck Air System and Brakes Brake Hydraulic System
777D and 777E Off-Highway Truck Air System and Brakes Air Flow Schematic
2006/11/20 Caterpillar Genuine Rollers Are Replaced By Caterpillar Classic Rollers {4180}
777D and 777E Off-Highway Truck Steering System Hydraulic Tank (Steering)
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Factory Passwords
14M Motor Grader Engine Supplement Refrigerant Condenser - Remove and Install
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Flash Programming
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines System Configuration Parameters
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Alternator Noise - Noisy Operation
773D Off-Highway Truck Air System and Brakes Pump and Motor (Secondary Steering and Brake Release)