PRODUCT IMPROVEMENT PROGRAM FOR REPLACING FUEL LINES ON CERTAIN C32 MARINE ENGINES
Usage:
REBE6636-01
Show/hide table
10Mar2011 |
(Revised 26May2011) |
U-99
A-82
D-88
O-92
TM-12
Show/hide table
Safety | PRODUCT IMPROVEMENT PROGRAM FOR REPLACING FUEL LINES ON CERTAIN C32 MARINE ENGINES |
|
1274 1261 1712 | PI10847 |
Show/hide table
NOTE: | This Program must be administered as soon as possible.
When reporting the repair, use "PI10847" as the Part Number and "7751" as the Group Number, "56" as the Warranty Claim
Description Code and "T" as the SIMS Description Code.
|
Show/hide table
Show/hide table
Show/hide table
NOTE: | This Revised Service Letter replaces the 10 March 2011 Service Letter. Changes have been made to Service Claim Allowance, Parts List, and Rework Procedure. |
Show/hide table
PROBLEM
Show/hide table
The fuel lines need to be replaced on certain C32 Marine Engines. The existing fuel lines can develop leaks which can in conjunction with other factors or circumstances, result in a risk of personal injury or death. |
AFFECTED PRODUCT
Show/hide table
Model | Identification Number |
*******Group 1******* | |
C32 | RNX00301-00303, 311, 314-316, 345, 350, 355, 359-360, 368, 370 RNY00751, 780, 805-806, 810, 813-816, 819, 829-830, 836, 849, 866, 883-884, 888, 892, 896, 901, 910-911, 936-937, 944-946, 950, 980, 990, 997, 1001, 1008, 1010, 1015-1016 |
Show/hide table
*******Group 2******* | |
C32 | RNX00299, 310, 322, 334, 336, 338-339, 363-364 RNY00777, 783, 789-790, 800, 811, 835, 844, 854, 858-859, 863, 871, 875, 908, 920-921, 928-929, 931, 933-934, 948, 957, 962-963, 987, 998 |
Show/hide table
*******Group 3******* | |
C32 | RNX00297, 304, 306, 308-309, 312, 317, 327-328, 335, 344, 347-349, 367, 369, 373-374 RNY00752, 778-779, 804, 807-809, 812, 817, 820, 826, 828, 842, 847-848, 862, 867, 882, 893, 897-898, 902-903, 906, 909, 912, 930, 935, 939-943, 949, 951, 975, 986, 988-989, 993, 1002, 1011-1013, 1017 |
Show/hide table
*******Group 4******* | |
C32 | RNX00298, 300, 305, 307, 313, 318-321, 323-326, 329-331, 337, 340-343, 346, 352-354, 356-358, 361-362, 365-366 RNY00765, 772, 774-776, 781-782, 784-785, 788, 801, 818, 821-822, 824-825, 837-841, 855, 857, 860-861, 864-865, 869-870, 874, 878, 880-881, 895, 907, 913-917, 923-924, 932, 938, 947, 952-956, 958-961, 965-969, 973, 984-985, 991, 996, 1000, 1006 |
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
*******Group 1******* | ||
6 | 1P1376 | CONNECTOR-STOR |
9 | 4L6454 | BOLT |
2 | 4L6459 | BOLT |
14 | 5P1075 | WASHER-HARD |
1 | 5P2424 | BOLT |
4 | 5P4116 | WASHER-HARD |
4 | 5S7379 | BOLT |
1 | 5V9221 | SPACER |
3 | 6D3479 | CLIP |
4 | 6V8189 | NUT-FULL |
1 | 6V8625 | ADAPTER-ELBOW |
1 | 6V8722 | ADAPTER-ELBOW |
1 | 6V8782 | ADAPTER-TEE |
18 | 6V8801 | NUT |
1 | 6V8982 | ADAPTER-ELBOW |
1 | 6V9844 | ADAPTER-TEE |
2 | 6V9852 | ADAPTER-ELBOW |
2 | 6V9873 | ADAPTER-STR |
2 | 7V6571 | GROMMET |
3 | 7X0288 | BOLT |
1 | 7X0732 | WASHER-HARD |
1 | 8C8989 | ADAPTER-ELBOW |
1 | 8M0505 | ADAPTER-STR |
1 | 8S0023 | CLIP |
1 | 8S0024 | CLIP |
1 | 8T1576 | ADAPTER-STR |
5 | 8T1887 | CLIP |
5 | 8T1888 | CLIP |
2 | 8T1889 | CLIP-2 PIECE |
2 | 8T1890 | CLIP-2 PIECE |
6 | 8T2502 | BOLT |
1 | 8T4223 | WASHER-HARD |
31 | 8T4896 | WASHER-HARD |
2 | 8T6876 | ADAPTER-ELBOW |
3 | 9B7237 | BOLT |
1 | 9M4136 | SPACER |
2 | 9S8005 | PLUG-STOR |
1 | 0908635 | SPACER |
1 | 1220450 | GROMMET |
1 | 1293172 | STUD-BOLT |
1 | 1700610 | STUD-BOLT |
6 | 2147568 | SEAL-O-RING-STOR |
14 | 2287090 | SEAL-O-RING-ORFS |
6 | 2287091 | SEAL-O-RING-ORS |
4 | 2373759 | STUD-BOLT |
4 | 2385080 | SEAL-O-RING-STOR |
1 | 2385081 | SEAL-O-RING-STOR |
2 | 2950758 | INDICATOR-FUEL |
1 | 2971456 | BRACKET |
2 | 3072673 | PLUG AS |
2 | 3256994 | CLIP-HALF SLOT |
2 | 3256995 | CLIP-HALF TAB |
2 | 3537956 | GROMMET |
5 | 3537957 | GROMMET |
1 | 3644034 | MANIFOLD-FUEL |
1 | 3645893 | HOSE AS-FUEL |
1 | 3645898 | HOSE AS-FUEL |
2 | 3645899 | HOSE AS-FUEL |
1 | 3648552 | TUBE AS-FUEL |
1 | 3648677 | HOSE AS-FUEL |
1 | 3648678 | TUBE AS-FUEL |
1 | 3649371 | HOSE AS-FUEL |
1 | 3650505 | HOSE AS-FUEL |
1 | 3650657 | HOSE AS-FUEL |
1 | 3655173 | BRACKET AS |
1 | 3678542 | BRACKET AS |
1 | 3678637 | HOSE AS-FUEL |
1 | 3679987 | BRACKET |
1 | 3688869 | HOSE AS-FUEL |
1 | 3689038 | BRACKET AS |
1 | 3689039 | BRACKET AS |
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 45% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
*******Group 2******* | ||
6 | 1P1376 | CONNECTOR-STOR |
6 | 4L6454 | BOLT |
2 | 4L6459 | BOLT |
1 | 4P7581 | CLIP-LADDER |
14 | 5P1075 | WASHER-HARD |
4 | 5P4116 | WASHER-HARD |
4 | 5S7379 | BOLT |
1 | 6D3479 | CLIP |
2 | 6V3917 | SEAL-O-RING |
4 | 6V8189 | NUT-FULL |
1 | 6V8722 | ADAPTER-ELBOW |
16 | 6V8801 | NUT |
1 | 6V9852 | ADAPTER-ELBOW |
2 | 7V6571 | GROMMET |
3 | 7X0288 | BOLT |
1 | 7X0732 | WASHER-HARD |
1 | 8M0505 | ADAPTER-STR |
1 | 8S0023 | CLIP |
1 | 8S0024 | CLIP |
1 | 8T0315 | SEAL-O-RING-ORFS |
1 | 8T1576 | ADAPTER-STR |
5 | 8T1887 | CLIP |
5 | 8T1888 | CLIP |
2 | 8T1889 | CLIP-2 PIECE |
2 | 8T1890 | CLIP-2 PIECE |
1 | 8T2502 | BOLT |
24 | 8T4896 | WASHER-HARD |
4 | 9B7237 | BOLT |
1 | 9M4136 | SPACER |
2 | 9S8005 | PLUG-STOR |
1 | 0908635 | SPACER |
1 | 1220450 | GROMMET |
1 | 1293172 | STUD-BOLT |
1 | 1569791 | CONNECTOR-ORFS |
1 | 1700610 | STUD-BOLT |
6 | 2147568 | SEAL-O-RING-STOR |
2 | 2287090 | SEAL-O-RING-ORFS |
2 | 2287091 | SEAL-O-RING-ORS |
1 | 2314708 | SEAL-O-RING |
4 | 2373759 | STUD-BOLT |
5 | 2385080 | SEAL-O-RING-STOR |
1 | 2385081 | SEAL-O-RING-STOR |
2 | 2950758 | INDICATOR-FUEL |
1 | 2971456 | BRACKET |
2 | 3256994 | CLIP-HALF SLOT |
2 | 3256995 | CLIP-HALF TAB |
2 | 3537956 | GROMMET |
5 | 3537957 | GROMMET |
1 | 3644034 | MANIFOLD-FUEL |
1 | 3645893 | HOSE AS-FUEL |
1 | 3645898 | HOSE AS-FUEL |
2 | 3645899 | HOSE AS-FUEL |
1 | 3648552 | TUBE AS-FUEL |
1 | 3648678 | TUBE AS-FUEL |
1 | 3649371 | HOSE AS-FUEL |
1 | 3650506 | HOSE AS-FUEL |
1 | 3650657 | HOSE AS-FUEL |
1 | 3655173 | BRACKET AS |
1 | 3678542 | BRACKET AS |
1 | 3678637 | HOSE AS-FUEL |
1 | 3679987 | BRACKET |
1 | 3688869 | HOSE AS-FUEL |
1 | 3689038 | BRACKET AS |
1 | 3689039 | BRACKET AS |
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 45% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
*******Group 3******* | ||
6 | 1P1376 | CONNECTOR-STOR |
3 | 4L6454 | BOLT |
3 | 4L6459 | BOLT |
1 | 4L9337 | BOLT |
12 | 5P1075 | WASHER-HARD |
1 | 5P2424 | BOLT |
4 | 5P4116 | WASHER-HARD |
4 | 5S7379 | BOLT |
1 | 5V9221 | SPACER |
1 | 6D3479 | CLIP |
2 | 6V3917 | SEAL-O-RING |
4 | 6V8189 | NUT-FULL |
12 | 6V8801 | NUT |
1 | 6V8982 | ADAPTER-ELBOW |
1 | 6V9851 | ADAPTER-ELBOW |
2 | 7V6571 | GROMMET |
3 | 7X0288 | BOLT |
1 | 7X0732 | WASHER-HARD |
1 | 8M0505 | ADAPTER-STR |
2 | 8S0023 | CLIP |
2 | 8S0024 | CLIP |
1 | 8T0315 | SEAL-O-RING-ORFS |
4 | 8T1887 | CLIP |
4 | 8T1888 | CLIP |
2 | 8T1889 | CLIP-2 PIECE |
2 | 8T1890 | CLIP-2 PIECE |
1 | 8T2502 | BOLT |
1 | 8T4223 | WASHER-HARD |
18 | 8T4896 | WASHER-HARD |
2 | 9B7237 | BOLT |
1 | 9M4136 | SPACER |
2 | 9S8005 | PLUG-STOR |
1 | 0919035 | SPACER |
2 | 1220450 | GROMMET |
1 | 1269903 | CONNECTOR |
1 | 1293172 | STUD-BOLT |
1 | 1367227 | SEAL-O-RING |
1 | 1542302 | SPACER |
1 | 1569791 | CONNECTOR-ORFS |
2 | 1700610 | STUD-BOLT |
6 | 2147568 | SEAL-O-RING-STOR |
2 | 2287090 | SEAL-O-RING-ORFS |
2 | 2287091 | SEAL-O-RING-ORS |
1 | 2314708 | SEAL-O-RING |
4 | 2373759 | STUD-BOLT |
5 | 2385080 | SEAL-O-RING-STOR |
2 | 2950758 | INDICATOR-FUEL |
1 | 2971456 | BRACKET |
2 | 3256994 | CLIP-HALF SLOT |
2 | 3256995 | CLIP-HALF TAB |
2 | 3537956 | GROMMET |
4 | 3537957 | GROMMET |
1 | 3644034 | MANIFOLD-FUEL |
1 | 3645893 | HOSE AS-FUEL |
1 | 3645895 | HOSE AS-FUEL |
1 | 3645897 | TUBE AS-FUEL |
1 | 3645898 | HOSE AS-FUEL |
2 | 3645899 | HOSE AS-FUEL |
1 | 3648546 | HOSE AS-FUEL |
1 | 3648547 | HOSE AS-FUEL |
1 | 3648548 | HOSE AS-FUEL |
1 | 3655597 | HOSE AS-FUEL |
1 | 3678542 | BRACKET AS |
1 | 3678637 | HOSE AS-FUEL |
1 | 3679987 | BRACKET |
1 | 3689038 | BRACKET AS |
1 | 3689039 | BRACKET AS |
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 45% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
*******Group 4******* | ||
6 | 1P1376 | CONNECTOR-STOR |
7 | 4L6454 | BOLT |
3 | 4L6459 | BOLT |
1 | 4L9337 | BOLT |
15 | 5P1075 | WASHER-HARD |
4 | 5P4116 | WASHER-HARD |
4 | 5S7379 | BOLT |
3 | 6D3479 | CLIP |
4 | 6V8189 | NUT-FULL |
1 | 6V8782 | ADAPTER-TEE |
21 | 6V8801 | NUT |
1 | 6V8982 | ADAPTER-ELBOW |
1 | 6V9851 | ADAPTER-ELBOW |
2 | 6V9873 | ADAPTER-STR |
2 | 7V6571 | GROMMET |
3 | 7X0288 | BOLT |
1 | 7X0732 | WASHER-HARD |
1 | 8M0505 | ADAPTER-STR |
2 | 8S0023 | CLIP |
2 | 8S0024 | CLIP |
4 | 8T1887 | CLIP |
4 | 8T1888 | CLIP |
3 | 8T1889 | CLIP-2 PIECE |
3 | 8T1890 | CLIP-2 PIECE |
4 | 8T2502 | BOLT |
31 | 8T4896 | WASHER-HARD |
5 | 9B7237 | BOLT |
1 | 9M4136 | SPACER |
2 | 9S8005 | PLUG-STOR |
1 | 0919035 | SPACER |
2 | 1220450 | GROMMET |
1 | 1269903 | CONNECTOR |
1 | 1293172 | STUD-BOLT |
1 | 1367227 | SEAL-O-RING |
1 | 1542302 | SPACER |
1 | 1569791 | CONNECTOR-ORFS |
2 | 1700610 | STUD-BOLT |
4 | 2147568 | SEAL-O-RING-STOR |
10 | 2287090 | SEAL-O-RING-ORFS |
3 | 2287091 | SEAL-O-RING-ORS |
4 | 2373759 | STUD-BOLT |
3 | 2385080 | SEAL-O-RING-STOR |
2 | 2950758 | INDICATOR-FUEL |
1 | 2971456 | BRACKET |
2 | 3072673 | PLUG AS |
2 | 3256994 | CLIP-HALF SLOT |
2 | 3256995 | CLIP-HALF TAB |
1 | 3503657 | BRACKET AS |
1 | 3537953 | GROMMET |
2 | 3537956 | GROMMET |
4 | 3537957 | GROMMET |
1 | 3644034 | MANIFOLD-FUEL |
1 | 3645893 | HOSE AS-FUEL |
1 | 3645897 | TUBE AS-FUEL |
1 | 3645898 | HOSE AS-FUEL |
2 | 3645899 | HOSE AS-FUEL |
1 | 3648546 | HOSE AS-FUEL |
1 | 3648547 | HOSE AS-FUEL |
1 | 3648548 | HOSE AS-FUEL |
1 | 3648551 | HOSE AS-FUEL ? |
1 | 3678542 | BRACKET AS |
1 | 3678637 | HOSE AS-FUEL |
1 | 3679987 | BRACKET |
1 | 3689038 | BRACKET AS |
1 | 3689039 | BRACKET AS |
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 45% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. |
ACTION REQUIRED
Show/hide table
Replace the existing fuel lines with the new fuel lines. Refer to the attached Rework Procedure for details. |
Show/hide table
OWNER NOTIFICATION
Show/hide table
U.S. and Canadian owners will receive the attached Owner Notification. |
SERVICE CLAIM ALLOWANCES
Show/hide table
Show/hide table
NOTE: This is a 15.0-hour job for Group 1 | |||||
This includes all preparation work, parts handling, and an additional 1.0 hour to paint fuel lines and touch up. There is a $30 miscellaneous allowance for purchase of paint to match the engine. There is a $280 miscellaneous allowance for purchase of SOLAS tape (if required by Marine Classification Society). There is a $50 miscellaneous allowance for purchase of additional parts not called out on this service letter. |
Show/hide table
Show/hide table
Show/hide table
NOTE: This is a 15.0-hour job for Group 2 | |||||
This includes all preparation work, parts handling, and an additional 1.0 hour to paint fuel lines and touch up. There is a $30 miscellaneous allowance for purchase of paint to match the engine. There is a $280 miscellaneous allowance for purchase of SOLAS tape (if required by Marine Classification Society). There is a $50 miscellaneous allowance for purchase of additional parts not called out on this service letter. |
Show/hide table
Show/hide table
Show/hide table
NOTE: This is a 15.0-hour job for Group 3 | |||||
This includes all preparation work, parts handling, and an additional 1.0 hour to paint fuel lines and touch up. There is a $30 miscellaneous allowance for purchase of paint to match the engine. There is a $280 miscellaneous allowance for purchase of SOLAS tape (if required by Marine Classification Society). There is a $50 miscellaneous allowance for purchase of additional parts not called out on this service letter. |
Show/hide table
Show/hide table
Show/hide table
NOTE: This is a 15.0-hour job for Group 4 | |||||
This includes all preparation work, parts handling, and an additional 1.0 hour to paint fuel lines and touch up. There is a $30 miscellaneous allowance for purchase of paint to match the engine. There is a $280 miscellaneous allowance for purchase of SOLAS tape (if required by Marine Classification Society). There is a $50 miscellaneous allowance for purchase of additional parts not called out on this service letter. |
Show/hide table
PARTS DISPOSITION
Show/hide table
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE. |
Show/hide table
COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS XYZ Corporation 3240 Arrow Drive Anywhere, YZ 99999 SAFETY - PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES MODELS INVOLVED - C32 Marine Engines Dear Caterpillar Product Owner: The fuel lines need to be replaced on the products listed below. The existing fuel lines can develop leaks which can become a potential fire hazard and may, in conjunction with other factors or circumstances, result in a risk of personal injury or death. You will not be charged for the service performed. Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service. Please refer the dealer to their Service Letter dated 10Mar2011 when scheduling this service. We regret the inconvenience this may cause you, but urge you to have this service performed for your added safety and satisfaction. Caterpillar Inc. Identification #(s) Attached to 10Mar2011 Service Letter |
Show/hide table
Group Number 1 |
This rework procedure is for updating Left Hand Service Marine / Commercial Engines built with Duplex Fuel Filters and a front housing that incorporates a "mounted pad" as shown in Image 1.1.1. This procedure will outline the conversion to the new 368-8870 Main Fuel Lines Group, 368-8876 Duplex Fuel Filter Group, and 364-6618 Fuel Cooler Group. If you encounter a front housing dissimilar to the images in this service letter please contact your Marine Customer Service Representative for guidance. For torque specifications reference media number SENR3130. Note: It is critical that the correct rework group is identified by engine serial number and that the rework is followed step by step to ensure that incorrect assembly does not occur. |
Image1.1.1 |
Caution: Ensure the engine is shut down and steps have been taken to prevent any attempt to start the engine while fuel hoses are being updated. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Step 1: To allow access to the fuel system, remove both the right and left hand air cleaner assemblies from the turbochargers. Step 2: To allow access to the fuel transfer pump, remove the 310-3144 Air Tube as seen in Image 1.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 3: Remove the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 1.2.1. The 8T-0833 Service Tool can be used to aid the removal of the 275-0190 Coolant Tube. NOTE: The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. The 275-0191 Tube may also need to be moved for additional clearance. To reinstall the 275-0191 Tube the 8T-0315 O-Ring may be required. |
Image1.2.1 |
Step 4: To allow access to the fuel fittings that connect the left front head to the fuel lines, the 294-3315 Fuel Filter Base Assembly, 296-3691 Fuel Filter Bracket, and 269-6440 Fuel Filter Mounting Bracket will need to be removed. Step 5: Remove the old fuel lines called out in Image 1.3.1. |
Image1.3.1 |
Step 6: Remove the four 030-7937 Stand-off Connectors and 214-7568 O-Rings that are located on all four outer corners of the engine cylinder heads. NOTE: Use of the appropriate crowfoot wrench from the 5P-0336 Wrench Set will aid in the removal and installation of fuel system fittings and lines. Step 7: Remove the washers from beneath the stud bolts that mount the 297-1458 Brackets from both sides of the engine shown in Image 1.4.1. (Arrows) Step 8: Reinstall the mounting stud bolts and 297-1458 Brackets. |
Image1.4.1 |
NOTES: - To install the new fuel lines reference Images 1.5.1 though 1.5.5. For more detailed images reference the fuel lines groups in SIS WEB. When installing fuel lines that incorporate a hose assembly, a back-up wrench must be used to prevent any hose twisting and undo stress to the fuel lines. - When installing these new fuel lines the wiring harness will need to be re-routed in some areas to prevent interference. - Fuel line installation best practices should be followed. All fuel line connections should first be installed hand tight, all clips and clamps should then be installed, and finally all fuel connections should be tightened to the correct torque value. - All of the fuel lines metal surfaces and mounting hardware must be painted to match the engine prior to installation to prevent rusting. Ensure that all ends of the fuel lines are capped during the handling and paint process to prevent fuel system contamination. |
Image1.5.1 |
Image1.5.2 |
Image1.5.3 |
Image1.5.4 |
Image1.5.5 |
Image1.5.6 |
Step 9: Install four 1P-1376 Stand-off Connectors with four 214-7568 O-Rings located on all four outer corners of the cylinder heads. See the example at Detail G on Image 1.5.3. Step 10: Install the 364-8552 Tube Assembly to the fuel transfer pump inlet and the 364-8678 Tube Assembly to the fuel transfer pump outlet. Tighten both connections at the transfer pump to a torque of 55 Nm (40.6 ft-lb) as shown in Image 1.5.1. Step 11: Install the 364-5893 Hose Assembly and the 364-5898 Hose Assembly ensuring to properly tighten this connection as shown in Detail G on Image 1.5.3. Step 12: Install two of the previously removed fuel line clamp assemblies from the old fuel lines at locations shown in Detail C and Detail D in Image 1.5.1 and 1.5.3. Installation of these fuel line clamp assemblies will require two 4L-6459 Bolts, four 8T-4896 Washers, two 5P-4116 Washers, two 6V-8189 Nuts, two 237-3759 Stud Bolts, and two 6V-8801 Nuts for both of the clamp assemblies. The old 297-1456 Brackets that are already on the engine should be swapped with the bolts in this location. Step 13: Install the 364-9371 Hose Assembly as shown in Image 1.5.1. The 228-7090 O-Ring is required between the 364-8552 Tube Assembly and the 364-9371 Hose Assembly. Step 14: To secure the 364-5893 Hose Assembly install the 5P-4116 Washer, 6V-8189 Nut, 367-9987 Bracket, 8T-4896 Washer, 6V-8801 Nut, 4L-6454 Bolt, 5P-1075 Washer, 325-6994 Half Clip, 325-6995 Half Clip, 237-3759 Stud Bolt, and 353-7956 Grommet as shown at Item 1 on Detail E (Left hand side of engine). Step 15: To secure the 364-8678 Tube Assembly to the 367-9987 Bracket install the P-clip at Item 2 on Detail E. Installation will require the 7X-0288 Bolt, 5P-1075 Washer, 8T-4896 Washer, 6V-8801 Nut, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, and 9M-4136 Spacer. Step 16: Install a fuel line clamp assembly previously removed from the old lines as shown in Detail B on Image 1.5.1 and 1.5.3. Step 17: To secure the 364-5898 Hose Assembly shown in Detail F (Right hand side of the engine) on Image 1.5.1 and Image 1.5.3, install the 5P-4116 Washer, 6V-8189 Nut, 297-1456 Bracket, 325-6994 Half Clip, 325-6995 Half Clip, 353-7956 Grommet, 6V-8801 Nut, two 8T-4896 Washers, 237-3759 Stud Bolt, and 8T-2502 Bolt. Step 18: Install a fuel line clamp assembly previously removed from the old lines as shown in Detail A on Image 1.5.1 and 1.5.3. Step 19: Install the 368-9038 Bracket to the right hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers shown as Item 1 in Detail L. Step 20: Install the 368-9039 Bracket to the left hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers shown as Item 1 in Detail I. Step 21: Install the 170-0610 Stud Bolt (Item 2 in Detail J) and the 367-8542 Bracket (Item 1 in Detail J) with two 6V-8801 Nuts and two 8T-4896 Washers. |
Step 22A: Sub assemble the 364-4034 Manifold Block by installing the two 1P-1376 Connectors with two 214-7568 O-Rings (see Item 4 in Detail J) to the manifold and tighten to a torque of 48 Nm (35.4 ft-lb). Step 22B: Install the 8M-0505 Adapter with 238-5080 O-Ring (Item 5 in Detail J) to the manifold and tighten to a torque of 55 Nm (40.5 ft-lb). Step 22C: In the remaining two ports (not shown) install two 9S-8005 Plugs with two 238-5080 O-Rings and tighten to a torque of 70 Nm (51.6 ft-lb). Step 22D: Install the 364-4034 Manifold to the 367-8542 Bracket using two 7X-0288 Bolts and two 8T-4896 Washers (see Item 6 in Detail J). Step 23: To secure the 364-9371 Hose Assembly to the mounting pad on the left side of the front housing shown at Item 4 in Detail I, install two 5P-1075 Washers, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, 090-8635 spacer, and 4L-6454 Bolt. Step 24: Install the 367-8637 Hose Assembly shown in Image 1.5.1. Note: The fuel pressure regulating manifolds located on both sides of the front of the engine may need to be repositioned to allow the 367-8637 Hose Assembly to have adequate clearance to avoid interference. Step 25: To secure the 367-8637 Hose Assembly to the 367-8542 Bracket, install the 6V-8801 Nut, 4L-6459 Bolt, 7X-0732 Washer, two 8T-4896 Washers, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip (see Item 3 in Detail J in Image 1.5.4 and Image 1.5.5). Step 26: Install the two 364-5899 Hose Assemblies that connect the front 1P-1376 Connectors to the 364-4034 Manifold Block and tighten to a torque of 27 Nm (19.9 ft-lb) shown in Image 1.5.1. Step 27: To secure the 364-5899 Hose Assemblies to the 368-9039 Bracket on the left hand side of the engine and the 368-9038 Bracket on the right hand side of the engine shown in Images 1.5.1 and 1.5.4, install the 4L-6454 Bolt, 8T-4896 Washer, 7V-6571 Grommet, 6V-8801 Nut, two 8T-4896 Washers, 8T-1889 Clip, 8T-1890 Clip (see Item 2 in Detail I and Item 2 in Detail L). Step 28: Reinstall the 269-6440 Fuel Filter Mounting Bracket, 296-3691 Fuel Filter Bracket, and 294-3315 Fuel Filter Base Assembly. Step 29A: On the fuel filter base install the 6V-9852 adapter with the 228-7091 o-ring and the 6V-8722 elbow with the 238-5080 o-ring as shown as Item 1 in Detail H on Image 1.5.3 and Image 1.5.6 Step 29B: Install the 8T-1576 connector as shown in Item 2 in Detail H on Image 1.5.3 and Image 1.5.6. The 228-7091 O-ring and 238-5081 O-ring are required. Step 29C: On the fuel filter base remove the two existing 266-0889 (100 psi) gages and install tow new 295-0758 (150 psi) gages. Step 30: Install the 365-0657 Hose Assembly between the 364-8678 Tube Assembly and fuel filter base as shown in Image 1.5.1. The 228-7091 O-Ring is required between the 365-0657 Hose Assembly and the 364-8678 Tube Assembly. Step 31: Install the 368-8869 Hose Assembly between the 364-4034 Manifold Block, see Detail J on Image 1.5.4, and the fuel filter base as shown in Image 1.5.1. |
Step 32: Finish connecting the 364-9371 Hose Assembly to the fuel filter base as shown in Image 1.5.1. Step 33: Install the 364-8677 Hose Assembly as shown in Image 1.5.1. Step 34: To secure the 364-8677 Hose Assembly to the heat exchanger, install the 5V-9221 Spacer, 5P-2424 Bolt, and 8T-4223 Washer with the existing bracket and clamp as shown in Detail K in Images 1.5.1 and 1.5.3 Step 35: To secure the 364-9371 Hose Assembly to the 368-9038 Bracket as shown at Item 3 in Detail L on Images 1.5.1 and 1.5.4, install two 5P-1075 Washers, 6V-8801 Nut, 9B-7237 Bolt, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip. Step 36: To secure the 368-8869 Hose Assembly to the 368-9039 Bracket shown at Item 3 in Detail I, install the 4L-6454 Bolt, 5P-1075 Washer, 6V-8801 Nut, 8T-4896 Washer, 090-8635 Spacer, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip. Step 37: To secure the 368-8869 Hose Assembly to the Fuel Filter Bracket install the 5P-1075 washer, 365-5173 bracket, 8T-4896 washer, 9B-7273 bolt, 4P-7581 ladder clip, 122-0450 grommet, 8S-0023 clip, and 8S-0024 clip as shown as Item 1 in Image 1.8.1. |
Image1.8.1 |
Step 38: To secure the 364-9371 Hose Assembly to the 368-9039 Bracket shown at Item 4 on Detail I, install two 5P-1075 Washers, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, 6V-8801 Nut, and 9B-7237 Bolt. Step 39: Install the 365-0505 Hose Assembly between the Fuel Filter Base and the Heat Exchanger. Secure with existing hardware. Step 40: The turbocharger cooling vent line will need to be re-routed and secured to the 368-9039 Bracket on the left hand side of the engine using the 129-3172 Stud Bolt, 6D-3479 Clip, two 6V-8801 Nuts and two 8T-4896 Washers as shown at Item 5 on Detail I on Images 1.5.1 and 1.5.4. Step 41: Reinstall the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 1.2.1. The 8T-0833 Service Tool can be used to aid the installation of the 275-0190 Coolant Tube. NOTE: The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. Reinstall the 275-0191 Tube if necessary. To reinstall the 275-0191 Tube, the 8T-0315 O-Ring may be required. Step 42: Reinstall the 310-3144 Air Tube as seen in Image 1.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 43: Reinstall the air cleaners. Step 44: If required, add SOLAS tape to all fuel system joints. Step 45: These new fuel lines can cause the engines fuel pressure to raise above the alarm limits. If required flash the ECM to the latest flash file in SISweb to correct alarm set point. |
Group Number 2 |
This rework procedure is for updating Left Hand Service Marine / Commercial Engines built with Duplex Fuel Filters and a front housing that incorporates a "mounted pad" as shown in Image 2.1.1. This procedure will outline the conversion to the new 368-8870 Main Fuel Lines Group, 368-8876 Duplex Fuel Filter Group, and 364-6622 Fuel Cooler Group. If you encounter a front housing dissimilar to the images in this service letter please contact your Marine Customer Service Representative for guidance. For torque specifications reference media number SENR3130. Note: It is critical that the correct rework group is identified by engine serial number and that the rework is followed step by step to ensure that incorrect assembly does not occur. |
Image2.1.1 |
Caution: Ensure the engine is shut down and steps have been taken to prevent any attempt to start the engine while fuel hoses are being updated. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Step 1: To allow access to the fuel system, remove both the right and left hand air cleaner assemblies from the turbochargers. Step 2: To allow access to the fuel transfer pump, remove the 310-3144 Air Tube as seen in Image 2.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 3: Remove the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 2.2.1. The 8T-0833 Service Tool can be used to aid the removal of the 275-0190 Coolant Tube. NOTE: The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. The 275-0191 Tube may also need to be moved for additional clearance. To reinstall the 275-0191 Tube the 8T-0315 O-Ring may be required. |
Image2.2.1 |
Step 4: To allow access to the fuel fittings that connect the left front head to the fuel lines, the 294-3315 Fuel Filter Base Assembly, 296-3691 Fuel Filter Bracket, and 269-6440 Fuel Filter Mounting Bracket will need to be removed. Step 5: Remove the old fuel lines called out in Image 2.3.1. |
Image2.3.1 |
Step 6: Remove the four 030-7937 Stand-off Connectors and 214-7568 O-Rings that are located on all four outer corners of the engine cylinder heads. NOTE: Use of the appropriate crowfoot wrench from the 5P-0336 Wrench Set will aid in the removal and installation of fuel system fittings and lines. Step 7: Remove the washers from beneath the stud bolts that mount the 297-1458 Brackets from both sides of the engine shown in Image 2.4.1. (Arrows) Step 8: Reinstall the mounting stud bolts and 297-1458 Brackets. |
Image2.4.1 |
NOTES: - To install the new fuel lines reference Images 2.5.1 though 2.5.5. For more detailed images reference the fuel lines groups in SIS WEB. When installing fuel lines that incorporate a hose assembly, a back-up wrench must be used to prevent any hose twisting and undo stress to the fuel lines. - When installing these new fuel lines the wiring harness will need to be re-routed in some areas to prevent interference. - Fuel line installation best practices should be followed. All fuel line connections should first be installed hand tight, all clips and clamps should then be installed, and finally all fuel connections should be tightened to the correct torque value. - All of the fuel lines metal surfaces and mounting hardware must be painted to match the engine prior to installation to prevent rusting. Ensure that all ends of the fuel lines are capped during the handling and paint process to prevent fuel system contamination. |
Image2.5.1 |
Image2.5.2 |
Image2.5.3 |
Image2.5.4 |
Image2.5.5 |
Image2.5.6 |
Step 9: Install four 1P-1376 Stand-off Connectors with four 214-7568 O-Rings located on all four outer corners of the cylinder heads. See the example at Detail G on Image 2.5.3. Step 10: Install the 364-8552 Tube Assembly to the fuel transfer pump inlet and the 364-8678 Tube Assembly to the fuel transfer pump outlet. Tighten both connections at the transfer pump to a torque of 55 Nm (40.6 ft-lb) as shown in Image 2.5.1. Step 11: Install the 364-5893 Hose Assembly and the 364-5898 Hose Assembly ensuring to properly tighten this connection as shown in Detail G on Image 2.5.3. Step 12: Install two of the previously removed fuel line clamp assemblies from the old fuel lines at locations shown in Detail C and Detail D in Image 2.5.1 and 2.5.3. Installation of these fuel line clamp assemblies will require two 4L-6459 Bolts, four 8T-4896 Washers, two 5P-4116 Washers, two 6V-8189 Nuts, two 237-3759 Stud Bolts, and two 6V-8801 Nuts for both of the clamp assemblies. The old 297-1456 Brackets that are already on the engine should be swapped with the bolts in this location. Step 13: Install the 364-9371 Hose Assembly as shown in Image 2.5.1. The 228-7090 O-Ring is required between the 364-8552 Tube Assembly and the 364-9371 Hose Assembly. Step 14: To secure the 364-5893 Hose Assembly install the 5P-4116 Washer, 6V-8189 Nut, 367-9987 Bracket, 8T-4896 Washer, 6V-8801 Nut, 4L-6454 Bolt, 5P-1075 Washer, 325-6994 Half Clip, 325-6995 Half Clip, 237-3759 Stud Bolt, and 353-7956 Grommet as shown at Item 1 on Detail E (Left hand side of engine). Step 15: To secure the 364-8678 Tube Assembly to the 367-9987 Bracket install the P-clip at Item 2 on Detail E. Installation will require the 7X-0288 Bolt, 5P-1075 Washer, 8T-4896 Washer, 6V-8801 Nut, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, and 9M-4136 Spacer. Step 16: Install a fuel line clamp assembly previously removed from the old lines as shown in Detail B on Image 2.5.1 and 2.5.3. Step 17: To secure the 364-5898 Hose Assembly shown in Detail F (Right hand side of the engine) on Image 2.5.1 and Image 2.5.3, install the 5P-4116 Washer, 6V-8189 Nut, 297-1456 Bracket, 325-6994 Half Clip, 325-6995 Half Clip, 353-7956 Grommet, 6V-8801 Nut, two 8T-4896 Washers, 237-3759 Stud Bolt, and 8T-2502 Bolt. Step 18: Install a fuel line clamp assembly previously removed from the old lines as shown in Detail A on Image 2.5.1 and 2.5.3. Step 19: Install the 368-9038 Bracket to the right hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers shown as Item 1 in Detail L. Step 20: Install the 368-9039 Bracket to the left hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers shown as Item 1 in Detail I. Step 21: Install the 170-0610 Stud Bolt (Item 2 in Detail J) and the 367-8542 Bracket (Item 1 in Detail J) with two 6V-8801 Nuts and two 8T-4896 Washers. |
Step 22A: Sub assemble the 364-4034 Manifold Block by installing the two 1P-1376 Connectors with two 214-7568 O-Rings (see Item 4 in Detail J) to the manifold and tighten to a torque of 48 Nm (35.4 ft-lb). Step 22B: Install the 8M-0505 Adapter with 238-5080 O-Ring (Item 5 in Detail J) to the manifold and tighten to a torque of 55 Nm (40.5 ft-lb). Step 22C: In the remaining two ports (not shown) install two 9S-8005 Plugs with two 238-5080 O-Rings and tighten to a torque of 70 Nm (51.6 ft-lb). Step 22D: Install the 364-4034 Manifold to the 367-8542 Bracket using two 7X-0288 Bolts and two 8T-4896 Washers (see Item 6 in Detail J). Step 23: To secure the 364-9371 Hose Assembly to the mounting pad on the left side of the front housing shown at Item 4 in Detail I, install two 5P-1075 Washers, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, 090-8635 spacer, and 4L-6454 Bolt. Step 24: Install the 367-8637 Hose Assembly shown in Image 1.5.1. Note: The fuel pressure regulating manifolds located on both sides of the front of the engine may need to be repositioned to allow the 367-8637 Hose Assembly to have adequate clearance to avoid interference. Step 25: To secure the 367-8637 Hose Assembly to the 367-8542 Bracket, install the 6V-8801 Nut, 4L-6459 Bolt, 7X-0732 Washer, two 8T-4896 Washers, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip (see Item 3 in Detail J in Image 2.5.4 and Image 2.5.5). Step 26: Install the two 364-5899 Hose Assemblies that connect the front 1P-1376 Connectors to the 364-4034 Manifold Block and tighten to a torque of 27 Nm (19.9 ft-lb) shown in Image 1.5.1. Step 27: To secure the 364-5899 Hose Assemblies to the 368-9039 Bracket on the left hand side of the engine and the 368-9038 Bracket on the right hand side of the engine shown in Images 1.5.1 and 1.5.4, install the 4L-6454 Bolt, 8T-4896 Washer, 7V-6571 Grommet, 6V-8801 Nut, two 8T-4896 Washers, 8T-1889 Clip, 8T-1890 Clip (see Item 2 in Detail I and Item 2 in Detail L). Step 28: Reinstall the 269-6440 Fuel Filter Mounting Bracket, 296-3691 Fuel Filter Bracket, and 294-3315 Fuel Filter Base Assembly. Step 29A: On the fuel filter base install the 6V-9852 adapter with the 228-7091 o-ring and the 6V-8722 elbow with the 238-5080 o-ring as shown as Item 1 in Detail H on Image 2.5.3 and Image 2.5.6 Step 29B: Install the 8T-1576 connector as shown in Item 2 in Detail H on Image 2.5.3 and Image 2.5.6. The 228-7091 O-ring and 238-5081 O-ring are required. Step 29C: On the fuel filter base remove the two existing 266-0889 (100 psi) gages and install tow new 295-0758 (150 psi) gages. Step 30: Install the 365-0657 Hose Assembly between the 364-8678 Tube Assembly and fuel filter base as shown in Image 1.5.1. The 228-7091 O-Ring is required between the 365-0657 Hose Assembly and the 364-8678 Tube Assembly. Step 31: Install the 368-8869 Hose Assembly between the 364-4034 Manifold Block, see Detail J on Image 2.5.4, and the fuel filter base as shown in Image 2.5.1. |
Step 32: Finish connecting the 364-9371 Hose Assembly to the fuel filter base as shown in Image 2.5.1. Step 33: Install the 365-0506 Hose Assembly as shown in Image 2.5.1. Step 34: To secure the 365-0506 Hose Assembly to the fuel filter bracket with the existing hardware. Step 35: To secure the 364-9371 Hose Assembly to the 368-9038 Bracket as shown at Item 3 in Detail L on Images 1.5.1 and 1.5.4, install two 5P-1075 Washers, 6V-8801 Nut, 9B-7237 Bolt, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip. Step 36: To secure the 368-8869 Hose Assembly to the 368-9039 Bracket shown at Item 3 in Detail I, install the 4L-6454 Bolt, 5P-1075 Washer, 6V-8801 Nut, 8T-4896 Washer, 090-8635 Spacer, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip. Step 37A: To secure the 368-8869 Hose Assembly to the Fuel Filter Bracket install the 5P-1075 washer, 365-5173 bracket, 8T-4896 washer, 9B-7273 bolt, 4P-7581 ladder clip, 122-0450 grommet, 8S-0023 clip, and 8S-0024 clip as shown as Item 1 in Image 2.8.1. Step 37B: To secure the 365-0506 hose assembly to the Fuel Filter Bracket install the existing 297-1637 bracket, 4L-6459 bolt, 5P-1075 washer, 6V-8801 nut, and 4P-0707 clamp assembly as shown as Item 2 in Image 2.8.1. |
Image2.8.1 |
Step 38: To secure the 364-9371 Hose Assembly to the 368-9039 Bracket shown at Item 4 on Detail I, install two 5P-1075 Washers, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, 6V-8801 Nut, and 9B-7237 Bolt. Step 39: The turbocharger cooling vent line will need to be re-routed and secured to the 368-9039 Bracket on the left hand side of the engine using the 129-3172 Stud Bolt, 6D-3479 Clip, two 6V-8801 Nuts and two 8T-4896 Washers as shown at Item 5 on Detail I on Images 2.5.1 and 2.5.4. Step 40: Reinstall the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 2.2.1. The 8T-0833 Service Tool can be used to aid the installation of the 275-0190 Coolant Tube. NOTE: The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. Reinstall the 275-0191 Tube if necessary. To reinstall the 275-0191 Tube, the 8T-0315 O-Ring may be required. Step 41: Reinstall the 310-3144 Air Tube as seen in Image 2.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 42: Reinstall the air cleaners. Step 43: If required, add SOLAS tape to all fuel system joints. Step 44: These new fuel lines can cause the engines fuel pressure to raise above the alarm limits. If required flash the ECM to the latest flash file in SISweb to correct alarm set point. |
Group Number 3 |
This rework procedure is for updating Right Hand Service Marine / Commercial Engines built with Duplex Fuel Filters and a front housing that incorporates a "mounting pad" as shown in Image 3.1.1. This procedure will outline the conversion to the new 368-8870 Main Fuel Lines Group, 368-8875 Duplex Fuel Filter Group, and 364-6617 Fuel Cooler Group. If you encounter a front housing dissimilar to the images in this service letter please contact your Marine Customer Service Representative for guidance. For torque specifications reference media number SENR3130. Note: It is critical that the correct rework group is identified by engine serial number and that the rework is followed step by step to ensure that incorrect assembly does not occur. Caution: Ensure the engine is shut down and steps have been taken to prevent any attempt to start the engine while fuel hoses are being updated. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Image3.1.1 |
Step 1: To allow access to the fuel system, remove both the right and left hand air cleaner assemblies from the turbochargers. Step 2: To allow access to the fuel transfer pump, remove the 310-3144 Air Tube as seen in Image 3.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 3: Remove the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 3.2.1. The 8T-0833 Service Tool can be used to aid the removal of the 275-0190 Coolant Tube. NOTE: The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. The 275-0191 Tube may also need to be moved for additional clearance. To reinstall the 275-0191 Tube the 8T-0315 O-Ring may be required. |
Image3.2.1 |
Step 4: To allow access to the fuel fittings that connect the right front head to the fuel lines, the 294-3316 Fuel Filter Base Assembly, 296-3692 Fuel Filter Bracket, and 269-6440 Fuel Filter Mounting Bracket will need to be removed. Step 5: Remove the old fuel lines called out in Image 3.3.1. |
Image3.3.1 |
Step 6: Remove the four 030-7937 Stand-off Connectors and 214-7568 O-Rings that are located on all four outer corners of the engine cylinder heads. NOTE: Use of the appropriate crowfoot wrench from the 5P-0336 Wrench Set will aid in the removal and installation of fuel system fittings and lines. Step 7: Remove the washers from beneath the stud bolts that mount the 297-1458 Brackets from both sides of the engine shown in Image 3.4.1. (Arrows) Step 8: Reinstall the mounting stud bolts and 297-1458 Brackets. |
Image3.4.1 |
NOTE: - To install the new fuel lines reference Images 3.5.1 though 3.5.5. For more detailed images reference the fuel lines groups in SIS WEB. - When installing fuel lines that incorporate a hose assembly, a back-up wrench must be used to prevent any hose twisting and undo stress to the fuel lines. - When installing these new fuel lines the wiring harness will need to be re-routed in some areas to prevent interference. - Fuel line installation best practices should be followed. All fuel line connections should first be installed hand tight, all clips and clamps should then be installed, and finally all fuel connections should be tightened to the correct torque value. - All of the fuel lines metal surfaces and mounting hardware must be painted to match the engine prior to installation to prevent rusting. Ensure that all ends of the fuel lines are capped during the handling and paint process to prevent fuel system contamination. |
Image3.5.1 |
Image3.5.2 |
Image3.5.3 |
Image3.5.4 |
Image3.5.5 |
Image3.5.6 |
Step 9: Install four 1P-1376 Stand-off Connectors with 214-7568 O-Rings located on all four outer corners of the cylinder heads, see the example at Detail G on Image 2.5.3. Step 10: Install the 364-8546 Hose Assembly to the fuel transfer pump inlet and the 364-5897 Tube Assembly to the fuel transfer pump outlet. Tighten both connections for the transfer pump to a torque of 55 Nm (40.6 ft-lb) as shown in Image 3.5.1. Step 11: Install the 364-5893 Hose Assembly and the 364-5898 Hose Assembly ensuring to properly tighten this connection as shown in Detail G on Image 3.5.4. Step 12: Install two of the previously removed fuel line clamp assemblies from the old fuel lines at locations shown in Detail C and Detail D in Images 3.5.1 and 3.5.3. Installation of these fuel line clamp assemblies will require two 4L-6459 Bolts, four 8T-4896 Washers, two 5P-4116 Washers, two 6V-8189 Nuts, two 237-3759 Stud Bolts, and two 6V-8801 Nuts for both of the clamp assemblies. The old 297-1456 Brackets that are already on the engine should be swapped with the bolts in this location. Step 13: Install the 364-8547 Hose Assembly shown in Images 3.5.1 and 3.5.2. The 228-7090 O-Ring is required between the 364-8547 Hose Assembly and the 364-5897 Tube Assembly. Step 14: To secure the 364-5893 Hose Assembly as seen on Images 3.5.1 and 3.5.3, install the 5P-4116 Washer, 6V-8189 Nut, 367-9987 Bracket, 8T-4896 Washer, 6V-8801 Nut, 4L-6454 Bolt, 5P-1075 Washer, 325-6994 Half Clip, 325-6995 Half Clip, 237-3759 Stud Bolt, and 353-7956 Grommet as shown at Item 1 on Detail E (Left hand side of engine). Step 15: To secure the 364-5897 Tube Assembly to the 367-9987 Bracket install the P-clip at Item 2 on Detail E. Installation will require the 7X-0288 Bolt, 5P-1075 Washer, 8T-4896 Washer, 6V-8801 Nut, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, 9M-4136 Spacer. Step 16: Install fuel line clamp assembly previously removed from the old lines as shown in Detail B on Image 3.5.1 and 3.5.3. Step 17: To secure the 364-5898 Hose Assembly as shown in Detail F (Right hand side of the engine) on Images 3.5.1 and 3.5.3 install the 5P-4116 Washer, 6V-8189 Nut, 297-1456 Bracket, 325-6994 Half Clip, 325-6995 Half Clip, 353-7956 Grommet, 6V-8801 Nut, two 8T-4896 Washers, 237-3759 Stud Bolts, and 8T-2502 Bolt. Step 18: Install a fuel line clamp assembly previously removed from the old lines as shown in Detail A on Images 3.5.1 and 3.5.3. Step 19: Install the 368-9038 Bracket to the right hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers as shown as Item 1 in Detail I. Step 20: Install the 368-9039 Bracket to the left hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers as shown as Item 1 in Detail L. Step 21: Install the 170-0610 Stud Bolt (Item 2 in Detail J) and the 367-8542 Bracket (Item 1 in Detail J) with two 6V-8801 Nuts and two 8T-4896 Washers. Step 22A: Sub assemble the 364-4034 Manifold Block by installing the two 1P-1376 Connectors with two 214-7568 O-Rings (see Item 4 in Detail J) to the manifold and tighten to a torque of 48 Nm (35.4 ft-lb). Step 22B: Install the 8M-0505 Adapter with 238-5080 O-Ring (Item 6 in Detail J) to the manifold and tighten to a torque of 55 Nm (40.5 ft-lb). Step 22C: Install two 9S-8005 Plugs with two 238-5080 O-Rings and tighten to a torque of 70 Nm (51.6 ft-lb) (see Item 5 Detail J). Step 22D: Install the 364-4034 Manifold to the 367-8542 Bracket using two 7X-0288 Bolts and two 8T-4896 Washers (see Item 7 in Detail J). |
Step 23: Install the 367-8637 Hose Assembly shown in Image 3.5.1. Note: The fuel pressure regulating manifolds located on both sides of the front of the engine may need to be repositioned to allow the 367-8637 Hose Assembly to have adequate clearance to avoid interference. Step 24: To secure the 367-8637 Hose Assembly to the 367-8542 Bracket, install the 6V-8801 Nut, 4L-6459 Bolt, 7X-0732 Washer, two 8T-4896 Washers, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip (see Item 3 in Detail J in Image 3.5.4 and Image 3.5.5). Step 25: Install the two 364-5899 Hose Assemblies that connect the front 1P-1376 Connectors to the 364-4034 Manifold and tighten to a torque of 27 Nm (19.9 ft-lb) as shown in Image 3.5.1. Step 26: To secure the 364-5899 Hose Assemblies to the 368-9039 Bracket on the left hand side of the engine and the 368-9038 Bracket on the right hand side of the engine shown Images 3.5.1 and 3.5.4, install two 4L-6454 Bolts, two 7V-6571 Grommets, two 6V-8801 Nuts, four 8T-4896 Washers, two 8T-1889 Clips, and two 8T-1890 Clips (see Item 3 in Detail I and Item 2 in Detail L). Step 27: Reinstall the 269-6440 Fuel Filter Mounting Bracket, the 296-3692 Fuel Filter Bracket, and the 237-9311 Fuel Filter Base Assembly. Step 28A: Install a new 156-9791 connector on the fuel filter base as shown Item 1 in Detail H on Image 3.5.3 and Image 3.5.6. The 228-7091 O-ring and 238-5080 O-Ring are required. Step 28B: Install the 126-9903 connector with a 136-7227 o-ring and the 6V-9851 adapter with 228-7090 o-ring as shown in Item 3.5.6. Step 28C: Install a new 6V-8982 adapter as shown as Item 2 in Detail H on Image 3.5.3. The 228-7091 O-ring and 238-5080 O-ring are required. Step 28D: On the fuel filter base remove the two existing 266-0889 (100 psi) gages and install tow new 295-0758 (150 psi) gages. Step 29: Install the 364-8548 Hose Assembly between the 364-4034 Manifold and the fuel filter base as shown in Images 3.5.1 and 3.5.2. Step 30: Finish connecting the 364-8547 Hose Assembly to the fuel filter base as shown in Images 3.5.1 and 3.5.2. Step 31: To secure the 364-8547 Hose Assembly to the 368-9038 Bracket as shown at Item 3 in Detail I on Image 3.5.4 and the 368-9039 Bracket not shown, install two 5P-1075 Washers, 6V-8801 Nut, 9B-7237 Bolt, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip at each bracket. Step 32: To secure the 364-8548 Hose Assembly to the right front mounting pad on the front housing as shown in Item 4 in Detail I on Image 3.5.4, install 154-2302 Spacer, 4L-9337 Bolt, 5P-1075 Washer, 122-0450 Grommet, 8S-0023 Clip, and 8S-0024 Clip. Step 33: The turbocharger cooling vent line will need to be re-routed and secured to the 368-9039 Bracket on the left hand side of the engine using the 129-3172 Stud Bolt, 6D-3479 Clip, two 6V-8801 Nuts and two 8T-4896 Washers as show as Item 5 on Detail I on Images 3.5.1 and 3.5.4. Step 34: Install the 364-5895 Hose Assembly as shown in Images 3.5.1 and 3.5.2. Step 35: To secure the 364-5895 Hose Assembly to the heat exchanger install the 5V-9221 Spacer, 5P-2424 Bolt, 8T-4223 Washer with the existing bracket and clamp as shown in Detail K in Images 3.5.1 and 3.5.3. Step 36: Install the 365-5597 Hose Assembly as shown in Image 3.5.1 and 3.5.2 and secure with the existing hardware. Step 37: To secure the 364-8547 Hose Assembly to the Fuel Filter Bracket install the 091-9035 spacer, 170-0610 stud bolt, 5P-1075 washer, 122-0450 grommet, 8S-0023 clip, and 8S-0024 clip as shown as Item 1 in Image 3.7.1. |
Image3.7.1 |
Step 38: Reinstall the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 3.2.1. The 8T-0833 Service Tool can be used to aid the installation of the 275-0190 Coolant Tube. - The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. Reinstall the 275-0191 Tube if necessary. To reinstall the 275-0191 Tube the 8T-0315 O-Ring may be required. Step 39: Reinstall the 310-3144 Air Tube as seen in Image 3.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 40: Reinstall the air cleaners. Step 41: If required, add SOLAS tape to all fuel system joints. Step 42: These new fuel lines can cause the engines fuel pressure to raise above the alarm limits. If required flash the ECM to the latest flash file in SISweb to correct alarm set point. |
Group Number 4 |
This rework procedure is for updating Right Hand Service Marine / Commercial Engines built with Duplex Fuel Filters and a front housing that incorporates a "mounting pad" as shown in Image 4.1.1. This procedure will outline the conversion to the new 368-8870 Main Fuel Lines Group, 368-8875 Duplex Fuel Filter Group, and 364-6621 Fuel Cooler Group. If you encounter a front housing dissimilar to the images in this service letter please contact your Marine Customer Service Representative for guidance. For torque specifications reference media number SENR3130. Note: It is critical that the correct rework group is identified by engine serial number and that the rework is followed step by step to ensure that incorrect assembly does not occur. Caution: Ensure the engine is shut down and steps have been taken to prevent any attempt to start the engine while fuel hoses are being updated. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Image4.1.1 |
Step 1: To allow access to the fuel system, remove both the right and left hand air cleaner assemblies from the turbochargers. Step 2: To allow access to the fuel transfer pump, remove the 310-3144 Air Tube as seen in Image 1.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 3: Remove the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 4.2.1. The 8T-0833 Service Tool can be used to aid the removal of the 275-0190 Coolant Tube. NOTE: The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. The 275-0191 Tube may also need to be moved for additional clearance. To reinstall the 275-0191 Tube the 8T-0315 O-Ring may be required. |
Image4.2.1 |
Step 4: To allow access to the fuel fittings that connect the right front head to the fuel lines, the 294-3316 Fuel Filter Base Assembly, 296-3692 Fuel Filter Bracket, and 269-6440 Fuel Filter Mounting Bracket will need to be removed. Step 5: Remove the old fuel lines called out in Image 4.3.1. |
Image4.3.1 |
Step 6: Remove the four 030-7937 Stand-off Connectors and 214-7568 O-Rings that are located on all four outer corners of the engine cylinder heads. NOTE: Use of the appropriate crowfoot wrench from the 5P-0336 Wrench Set will aid in the removal and installation of fuel system fittings and lines. Step 7: Remove the washers from beneath the stud bolts that mount the 297-1458 Brackets from both sides of the engine shown in Image 4.4.1. (Arrows) Step 8: Reinstall the mounting stud bolts and 297-1458 Brackets. |
Image4.4.1 |
NOTE: - To install the new fuel lines reference Images 4.5.1 though 4.5.5. For more detailed images reference the fuel lines groups in SIS WEB. - When installing fuel lines that incorporate a hose assembly, a back-up wrench must be used to prevent any hose twisting and undo stress to the fuel lines. - When installing these new fuel lines the wiring harness will need to be re-routed in some areas to prevent interference. - Fuel line installation best practices should be followed. All fuel line connections should first be installed hand tight, all clips and clamps should then be installed, and finally all fuel connections should be tightened to the correct torque value. - All of the fuel lines metal surfaces and mounting hardware must be painted to match the engine prior to installation to prevent rusting. Ensure that all ends of the fuel lines are capped during the handling and paint process to prevent fuel system contamination. |
Image4.5.1 |
Image4.5.2 |
Image4.5.3 |
Image4.5.4 |
Image4.5.5 |
Image4.5.6 |
Step 9: Install four 1P-1376 Stand-off Connectors with 214-7568 O-Rings located on all four outer corners of the cylinder heads, see the example at Detail G on Image 4.5.3. Step 10: Install the 364-8546 Hose Assembly to the fuel transfer pump inlet and the 364-5897 Tube Assembly to the fuel transfer pump outlet. Tighten both connections for the transfer pump to a torque of 55 Nm (40.6 ft-lb) as shown in Image 4.5.1. Step 11: Install the 364-5893 Hose Assembly and the 364-5898 Hose Assembly ensuring to properly tighten this connection as shown in Detail G on Image 4.5.4. Step 12: Install two of the previously removed fuel line clamp assemblies from the old fuel lines at locations shown in Detail C and Detail D in Images 4.5.1 and 4.5.3. Installation of these fuel line clamp assemblies will require two 4L-6459 Bolts, four 8T-4896 Washers, two 5P-4116 Washers, two 6V-8189 Nuts, two 237-3759 Stud Bolts, and two 6V-8801 Nuts for both of the clamp assemblies. The old 297-1456 Brackets that are already on the engine should be swapped with the bolts in this location. Step 13: Install the 364-8547 Hose Assembly shown in Images 4.5.1 and 4.5.2. The 228-7090 O-Ring is required between the 364-8547 Hose Assembly and the 364-5897 Hose Assembly. Step 14: To secure the 364-5893 Hose Assembly as seen on Images 4.5.1 and 4.5.3, install the 5P-4116 Washer, 6V-8189 Nut, 367-9987 Bracket, 8T-4896 Washer, 6V-8801 Nut, 4L-6454 Bolt, 5P-1075 Washer, 325-6994 Half Clip, 325-6995 Half Clip, 237-3759 Stud Bolt, and 353-7956 Grommet as shown at Item 1 on Detail E (Left hand side of engine). Step 15: To secure the 364-5897 Tube Assembly to the 367-9987 Bracket install the P-clip at Item 2 on Detail E. Installation will require the 7X-0288 Bolt, 5P-1075 Washer, 8T-4896 Washer, 6V-8801 Nut, 8T-1887 Clip, 8T-1888 Clip, 353-7957 Grommet, 9M-4136 Spacer. Step 16: Install fuel line clamp assembly previously removed from the old lines as shown in Detail B on Image 4.5.1 and 4.5.3. Step 17: To secure the 364-5898 Hose Assembly as shown in Detail F (Right hand side of the engine) on Images 4.5.1 and 4.5.3 install the 5P-4116 Washer, 6V-8189 Nut, 297-1456 Bracket, 325-6994 Half Clip, 325-6995 Half Clip, 353-7956 Grommet, 6V-8801 Nut, two 8T-4896 Washers, 237-3759 Stud Bolts, and 8T-2502 Bolt. Step 18: Install a fuel line clamp assembly previously removed from the old lines as shown in Detail A on Images 4.5.1 and 4.5.3. Step 19: Install the 368-9038 Bracket to the right hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers as shown as Item 1 in Detail I. Step 20: Install the 368-9039 Bracket to the left hand front housing support with two 5S-7379 Bolts and two 5P-1075 Washers as shown as Item 1 in Detail L. Step 21: Install the 170-0610 Stud Bolt (Item 2 in Detail J) and the 367-8542 Bracket (Item 1 in Detail J) with two 6V-8801 Nuts and two 8T-4896 Washers. Step 22A: Sub assemble the 364-4034 Manifold Block by installing the two 1P-1376 Connectors with two 214-7568 O-Rings (see Item 4 in Detail J) to the manifold and tighten to a torque of 48 Nm (35.4 ft-lb). |
Step 22B: Install the 8M-0505 Adapter with 238-5080 O-Ring (Item 6 in Detail J) to the manifold and tighten to a torque of 55 Nm (40.5 ft-lb). Step 22C: Install two 9S-8005 Plugs with two 238-5080 O-Rings and tighten to a torque of 70 Nm (51.6 ft-lb) (see Item 5 Detail J). Step 22D: Install the 364-4034 Manifold to the 367-8542 Bracket using two 7X-0288 Bolts and two 8T-4896 Washers (see Item 7 in Detail J). Step 23: Install the 367-8637 Hose Assembly shown in Image 4.5.1. Note: The fuel pressure regulating manifolds located on both sides of the front of the engine may need to be repositioned to allow the 367-8637 Hose Assembly to have adequate clearance to avoid interference. Step 24: To secure the 367-8637 Hose Assembly to the 367-8542 Bracket, install the 6V-8801 Nut, 4L-6459 Bolt, 7X-0732 Washer, two 8T-4896 Washers, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip (see Item 3 in Detail J in Image 4.5.4 and Image 4.5.5). Step 25: Install the two 364-5899 Hose Assemblies that connect the front 1P-1376 Connectors to the 364-4034 Manifold and tighten to a torque of 27 Nm (19.9 ft-lb) as shown in Image 4.5.1. Step 26: To secure the 364-5899 Hose Assemblies to the 368-9039 Bracket on the left hand side of the engine and the 368-9038 Bracket on the right hand side of the engine shown Images 4.5.1 and 4.5.4, install two 4L-6454 Bolts, two 7V-6571 Grommets, two 6V-8801 Nuts, four 8T-4896 Washers, two 8T-1889 Clips, and two 8T-1890 Clips (see Item 3 in Detail I and Item 2 in Detail L). Step 27: Reinstall the 269-6440 Fuel Filter Mounting Bracket, the 296-3692 Fuel Filter Bracket, and the 294-3316 Filter Base Assembly. Step 28A: Install a new 156-9791 connector on the fuel filter base as shown Item 1 in Detail H on Image 4.5.3 and Image 4.5.6. The 228-7091 O-ring and 238-5080 O-Ring are required. Step 28B: Install the 126-9903 connector with a 136-7227 o-ring and the 6V-9851 adapter with 228-7090 o-ring as shown in Item 4.5.6. Step 28C: Install a new 6V-8982 adapter as shown as Item 2 in Detail H on Image 4.5.3. The 228-7091 O-ring and 238-5080 O-ring are required. Step 28D: On the fuel filter base remove the two existing 266-0889 (100 psi) gages and install tow new 295-0758 (150 psi) gages. Step 29: Install the 364-8548 Hose Assembly between the 364-4034 Manifold and the fuel filter base as shown in Images 4.5.1 and 4.5.2. Step 30: Finish connecting the 364-8547 Hose Assembly to the fuel filter base as shown in Images 4.5.1 and 4.5.2. Step 31: To secure the 364-8547 Hose Assembly to the 368-9038 Bracket as shown at Item 3 in Detail I on Image 3.5.4 and the 368-9039 Bracket not shown, install two 5P-1075 Washers, 6V-8801 Nut, 9B-7237 Bolt, 353-7957 Grommet, 8T-1887 Clip, and 8T-1888 Clip at each bracket. Step 32: To secure the 364-8548 Hose Assembly to the right front mounting pad on the front housing as shown in Item 4 in Detail I on Image 3.5.4, install 154-2302 Spacer, 4L-9337 Bolt, 5P-1075 Washer, 122-0450 Grommet, 8S-0023 Clip, and 8S-0024 Clip. Step 33: Install the 364-8551 Hose Assembly as shown in Image 4.5.1 and 4.5.2. Step 34: The turbocharger cooling vent line will need to be re-routed and secured to the 368-9039 Bracket on the left hand side of the engine using the 129-3172 Stud Bolt, 6D-3479 Clip, two 6V-8801 Nuts and two 8T-4896 Washers as show as Item 5 on Detail I on Images 2.5.1 and 2.5.4. Step 35A: To secure the 364-8547 Hose Assembly to the Fuel Filter Bracket install the 091-9035 spacer, 170-0610 stud bolt, 5P-1075 washer, 122-0450 grommet, 8S-0023 clip, and 8S-0024 clip as shown as Item 1 in Image 4.7.1. Step 35B: To secure the 364-8551 Hose Assembly install the 350-3657 bracket, 4L-6454 bolt, two 5P-1075 washers, 8T-1889 clip, 8T-1890 clip, 6V-8801 nut, and 353-7953 grommet as shown as Item 2 in Image 4.7.1 |
Image4.7.1 |
Step 36: Reinstall the 275-0190 Coolant Tube which connects the turbocharger to the cylinder head shown in Image 4.2.1. The 8T-0833 Service Tool can be used to aid the installation of the 275-0190 Coolant Tube. - The 231-4708 O-Ring is required to reinstall the 275-0190 Coolant Tube. Reinstall the 275-0191 Tube if necessary. To reinstall the 275-0191 Tube the 8T-0315 O-Ring may be required. Step 37: Reinstall the 310-3144 Air Tube as seen in Image 4.2.1 which connects the turbocharger to the aftercooler. NOTE: Two 6V-3917 O-Rings are required to reinstall the air tube. Step 38: Reinstall the air cleaners. Step 39: If required, add SOLAS tape to all fuel system joints. Step 40: These new fuel lines can cause the engines fuel pressure to raise above the alarm limits. If required flash the ECM to the latest flash file in SISweb to correct alarm set point. |
Caterpillar Information System:
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING FUEL LINES ON CERTAIN C32 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING FUEL LINES ON CERTAIN C32 MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ROTOR ASSEMBLY ON CERTAIN 3406C, 3456, C9, C15, AND C18 60 HZ GENERATOR SETS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ROTOR ASSEMBLY ON CERTAIN 3406C, 3456, C9, C15, AND C18 60 HZ GENERATOR SETS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN C175-16 OIL PAN GASKETS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN C175-16 OIL PAN GASKETS FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REWORKING THE MUFFLER EXHAUST OUTLET ON CERTAIN 345D EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REWORKING THE MUFFLER EXHAUST OUTLET ON CERTAIN 345D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN PRESSURE SWITCHES FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN PRESSURE SWITCHES FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REWORKING THE AIR FILTER ASSEMBLY ON CERTAIN C2.2 GENERATING SETS PRODUCT SUPPORT PROGRAM FOR REWORKING THE AIR FILTER ASSEMBLY ON CERTAIN C2.2 GENERATING SETS
PRODUCT SUPPORT PROGRAM FOR INSTALLING A WATER-COOLED THROTTLE ON CERTAIN G3516C, G3520C, G3516E, AND G3520E ENGINES PRODUCT SUPPORT PROGRAM FOR INSTALLING A WATER-COOLED THROTTLE ON CERTAIN G3516C, G3520C, G3516E, AND G3520E ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REPLACING PISTON RINGS ON CERTAIN C12, C18, AND 3406C MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REPLACING PISTON RINGS ON CERTAIN C12, C18, AND 3406C MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING FAILED HINGES ON CERTAIN 345C, 345D, AND 385C EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING FAILED HINGES ON CERTAIN 345C, 345D, AND 385C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL LINES ON CERTAIN C32 MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING THE AUXILIARY OIL FILTER ON CERTAIN C175-16 ELECTRIC POWER GENERATOR SETS PRODUCT IMPROVEMENT PROGRAM FOR REMOVING THE AUXILIARY OIL FILTER ON CERTAIN C175-16 ELECTRIC POWER GENERATOR SETS
PRODUCT IMPROVEMENT PROGRAM TO INSPECT AND POSSIBLY REMOVE CERTAIN 8N-6309, 4P-0710, 105-9741, 105-9742, 113-1578, AND 185-8786 AIR FILTER ELEMENTS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM TO INSPECT AND POSSIBLY REMOVE CERTAIN 8N-6309, 4P-0710, 105-9741, 105-9742, 113-1578, AND 185-8786 AIR FILTER ELEMENTS FROM DEALER PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 259-9150 RADIATOR SPIDER FAN WITH THE VALIDATED 319-5217 RADIATOR SPIDER FAN ON CERTAIN 3516C GENSETS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 259-9150 RADIATOR SPIDER FAN WITH THE VALIDATED 319-5217 RADIATOR SPIDER FAN ON CERTAIN 3516C GENSETS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING 0R3023 REMAN CAMSHAFT KITS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING 0R3023 REMAN CAMSHAFT KITS FROM DEALER PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM TO INSPECT AND POSSIBLY REMOVE CERTAIN 8N-3378, 131-2183, 7E-9632, 165-3817, 4P-0558, 113-4650, 113-1581, 132-9331, AND 132-9326 AIR FILTER GROUPS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM TO INSPECT AND POSSIBLY REMOVE CERTAIN 8N-3378, 131-2183, 7E-9632, 165-3817, 4P-0558, 113-4650, 113-1581, 132-9331, AND 132-9326 AIR FILTER GROUPS FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REPLACING FUEL INJECTORS AND BUTTONS ON CERTAIN 3512C AND SPF343C PETROLEUM ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING FUEL INJECTORS AND BUTTONS ON CERTAIN 3512C AND SPF343C PETROLEUM ENGINES
PRODUCT SUPPORT PROGRAM FOR UPDATING THE ENGINE SOFTWARE ON CERTAIN C13 AND C15 ON-HIGHWAY TRUCK ENGINES PRODUCT SUPPORT PROGRAM FOR UPDATING THE ENGINE SOFTWARE ON CERTAIN C13 AND C15 ON-HIGHWAY TRUCK ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING CERTAIN 6I-9255, 6T-1783, 6T-2317, 6Y-7219, 7T-1860, 102-8671, 147-2280, 169-7055, 221-9685, 241-4890, 262-7319, AND 262-7320 FRICTION DISCS IN DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING CERTAIN 6I-9255, 6T-1783, 6T-2317, 6Y-7219, 7T-1860, 102-8671, 147-2280, 169-7055, 221-9685, 241-4890, 262-7319, AND 262-7320 FRICTION DISCS IN DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REWORKING THE OPTIONAL SMMS NEUTRAL SWITCH CIRCUIT ON CERTAIN C32 MARINE ENGINES PROPULSION ENGINES PRODUCT SUPPORT PROGRAM FOR REWORKING THE OPTIONAL SMMS NEUTRAL SWITCH CIRCUIT ON CERTAIN C32 MARINE ENGINES PROPULSION ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING LEAKING FUEL INJECTORS ON CERTAIN 3512B, 3512C, AND 3516B MARINE ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING LEAKING FUEL INJECTORS ON CERTAIN 3512B, 3512C, AND 3516B MARINE ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING JACKET WATER PUMPS ON CERTAIN DEFENSE PRODUCTS C7 ENGINES FOR MILITARY ALL TERRAIN VEHICLES (MATV) PRODUCT SUPPORT PROGRAM FOR REPLACING JACKET WATER PUMPS ON CERTAIN DEFENSE PRODUCTS C7 ENGINES FOR MILITARY ALL TERRAIN VEHICLES (MATV)