Hydraulic Tank - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
B     | 138-7575     | 连杆支架     | 2     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
- 将七个 O 形密封圈 (68) 安装至垫块 (67) 。
Show/hide table
图 1 | g01091815 |
- 定位垫块 (67) 。
- 安装 2 个螺栓 (66) 。
Show/hide table
图 2 | g01091811 |
- 将 O 形密封圈安装到盖 (65) 上。 安装盖 (65) 和四个螺栓 (64) 。
- 将七个 O 形密封圈 (63) 安装至垫块 (62) 。
Show/hide table
图 3 | g01091813 |
- 定位垫块 (62) 。
- 安装 2 个螺栓 (59) 。
Show/hide table
图 4 | g01091812 |
- 将 O 形密封圈安装到盖 (61) 上。 安装盖 (61) 和四个螺栓 (60) 。
- 将 12 个 O 形密封圈 (58) 安装至垫块 (57) 。
Show/hide table
图 5 | g01091810 |
- 定位垫块 (57) 。
Show/hide table
图 6 | g01091808 |
- 安装 2 个螺栓 (54) 。
Show/hide table
图 7 | g01091807 |
- 将 O 形密封圈安装到盖 (56) 上。 安装盖 (56) 和四个螺栓 (55) 。
- 将 O 形密封圈 (49) 安装到排放塞 (48) 上。 将排放塞 (48) 安装到排放阀阀体 (47) 中。
Show/hide table
图 8 | g01091806 |
Show/hide table
图 9 | g01091826 |
- 拧紧排放塞 (48) 至扭矩为 68 ± 7 N·m (50 ± 5 lb ft)。
- 安装 O 形密封圈 (50) 、阀 (51) 、弹簧 (52) 和阀导管 (53)
- 安装排放阀组件 (47) 和两个锁紧螺母 (46) 。
Show/hide table
图 10 | g01091805 |
- 安装挡板管 (44) 和两个螺栓 (45) 。
Show/hide table
图 11 | g01091792 |
- 将 O 形密封圈安装到盖 (41) 上。 安装阀 (42) 、弹簧 (43) 、盖 (41) 和两个螺栓 (40) 。
Show/hide table
图 12 | g01091828 |
Show/hide table
图 13 | g01091791 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将两个螺柱 (37) 安装到滤清器座 (36) 上。 拧紧两个螺柱 (37) 至扭矩为 108 ± 14 N·m (80 ± 10 lb ft)。
Show/hide table
图 14 | g01091829 |
- 安装 10 个 O 形密封圈 (38) 。
- 安装 O 形密封圈 (39) 。
- 将滤清器座 (36) 定位到盖的外侧。
- 安装固定滤清器座 (36) 的两个螺栓 (35) 。
Show/hide table
图 15 | g01092199 |
- 将密封胶 (69) 涂覆到挡板 (33) 上,重叠密封胶 (69) 的两端以便完成密封。
Show/hide table
图 16 | g01091830 |
- 安装挡板 (33) 和 6 个螺栓 (34) 。
Show/hide table
图 17 | g01091762 |
- 安装密封垫 (31) 。
- 安装密封垫 (32) 。
- 将工具 (B) 和适当的起吊设备安装到盖 (29) 上。 盖 (29) 的重量约为 75 kg (165 lb)。
Show/hide table
图 18 | g01091753 |
- 定位盖组件 (28) 并安装 70 个螺栓 (29) 和锁紧螺母。
- 将两个螺栓 (25) 安装到液位表 (26) 上。 将 O 形密封圈 (28) 安装到两个螺栓 (25) 上。
Show/hide table
图 19 | g01116310 |
- 安装液位表 (26) 。 拧紧两个螺栓 (25) 至扭矩为 7 ± 1 N·m (62 ± 9 lb in)。
Show/hide table
图 20 | g01091816 |
- 安装支架 (27) 。
- 将 O 形密封圈 (70) 安装到螺栓 (22) 上。
Show/hide table
图 21 | g01092571 |
- 将螺栓 (22) 安装到盖 (17) 上。 将挡圈安装到螺栓 (22) 上。
- 安装 O 形密封圈 (24) 。
Show/hide table
图 22 | g01092573 |
- 安装六个盘簧 (21) 。 成对安装盘簧,使盘簧的外径彼此接触。
- 安装隔套 (20) 和挡圈 (19) 。
- 安装滤芯 (18) 和盖 (17) 。 拧紧螺栓 (16) 至扭矩为 56 ± 3 N·m (41 ± 2 lb ft)。
Show/hide table
图 23 | g01092556 |
Show/hide table
图 24 | g01092563 |
- 对其他滤清器组件重复步骤 33 至步骤 38。
- 将滤网 (14) 和 O 形密封圈 (15) 安装到加注口 (9) 上。
Show/hide table
图 25 | g01091751 |
- 将钢球 (12) 、板 (11) 和密封垫 (10) 安装到盖 (13) 上。
Show/hide table
图 26 | g01091750 |
- 安装加注口 (9) 和四个锁紧螺母 (8) 。
Show/hide table
图 27 | g01091748 |
- 将 O 形密封圈 (5) 、 (6) 和 (7) 安装到断路器安全阀 (4) 上。
Show/hide table
图 28 | g01099374 |
- 安装断路器安全阀 (4) 。
Show/hide table
图 29 | g01099373 |
- 安装滤芯 (3) 。
Show/hide table
图 30 | g01099372 |
- 安装盖 (2) 和扣环 (1) 。
Show/hide table
图 31 | g01091821 |
Caterpillar Information System:
R1300G Load Haul Dump Machine Systems Pilot Valve (STIC Steering) - Remove
725 and 730 Articulated Trucks Machine Systems Steering System Troubleshooting
R1300G Load Haul Dump Machine Systems Neutralizer Valve (Implement and Steering) - Remove and Install
R1300G Load Haul Dump Machine Systems Neutralizer Valve (STIC Steering) - Remove and Install
R1600G Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Disassemble
R1600G Load Haul Dump Machine Systems Hydraulic Tank - Disassemble
R1300G Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Install
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Radiator Core - Clean
446D Backhoe Loader Machine Systems Bucket - Remove and Install
797 Off-Highway Truck Front Axle Breather - Replace
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
725 and 730 Articulated Trucks Machine Systems Hoist System Troubleshooting
725 and 730 Articulated Trucks Machine Systems Piston Pump (Steering, Hoist) - Test and Adjust
725 and 730 Articulated Trucks Machine Systems Piston Pump (Brake, Hoist, Fan) - Test and Adjust
725 and 730 Articulated Trucks Machine Systems Electric Drive Pump (Secondary Steering) - Check
725 and 730 Articulated Trucks Machine Systems Service Brake Air - Purge
834H Wheel Dozer and 836H Landfill Compactor Axle Oil Cooler Filter - Replace - If Equipped
797B Off-Highway Truck Lifting and Tying Down the Machine
834H Wheel Dozer and 836H Landfill Compactor Axle Oscillation Bearings - Lubricate
725 and 730 Articulated Trucks Machine Systems Brake System Charging Pressure - Check
2004/09/06 New Dash Lamp With Improved Service Life Is Now Available {7450, 7451}
834H Wheel Dozer and 836H Landfill Compactor Backup Alarm - Test
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Hydraulic Fan System