Drive Shaft (Front) and Drive Shaft Support Bearing - Remove
Start By:
- Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering Frame Lock - Separate and Connect".
- Remove the center drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Center) - Remove and Install".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Disconnect hose assembly (1).
- Remove bolt (2) and retainer (3) from the splined end of the front drive shaft.
Show/hide table
Illustration 2 g01079132 - Remove O-ring seal (5) and yoke (4).
Show/hide table
Illustration 3 g01082251 Show/hide tableHot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
- Disconnect hose assemblies (6), (7) and (8).
Show/hide table
Illustration 4 g01079133 - Remove eight bolts (9).
- Remove spider (10).
Show/hide table
Illustration 5 g01079137 - Use two people or a suitable jack to remove front drive shaft (11). The weight of front drive shaft (11) is
44 kg (97 lb) .Show/hide tableIllustration 6 g01079134 - Remove six bolts (12) and the nuts that hold support bearing (13) to the front main frame.
- Remove support bearing (13).
Show/hide table
Illustration 1 | g01079131 |
Caterpillar Information System:
R2900G Load Haul Dump Machine Systems Steering Metering Pump - Remove
770 and 772 Off-Highway Truck Service Brakes - Inspect
AP-655C and BG-2255C Asphalt Pavers Ground Fault - Check - If Equipped
770 and 772 Off-Highway Truck Secondary Steering - Test
2004/08/23 The Addition of Plates Improves the Service Life of the Cowl Assembly {1353, 7051, 7251, 7254}
PF-300C and PS-300C Pneumatic Compactors Machine System Suspension System - PS-300C
Installation of the AccuGrade Electronic Components for Motor Graders{7220} Installation of the AccuGrade Electronic Components for Motor Graders{7220}
AP-800D and BG-230D Asphalt Pavers Conveyor Systems Piston Pump Neutral - Test and Adjust
AP-800D and BG-230D Asphalt Pavers Engine Oil and Filter - Change
AP-800D and BG-230D Asphalt Pavers Engine Oil Sample - Obtain
2004/10/11 New Test ECM Available for MAC 14 Drive Train {7610}
AP-800D and BG-230D Asphalt Pavers Conveyor Systems Relief Valve (Main) - Test
R2900G Load Haul Dump Machine Systems Steering Metering Pump - Install
R2900G Load Haul Dump Machine Systems Brake Accumulator - Remove
770 and 772 Off-Highway Truck Steering System Oil - Change
AP-800D and BG-230D Asphalt Pavers Conveyor Systems General Information
446D Backhoe Loader Engine Supplement Fan Drive - Assemble
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Relief Valve (Line) - Test and Adjust
446D Backhoe Loader Engine Supplement Fan Drive - Disassemble
770 and 772 Off-Highway Truck Steering System Oil Level - Check
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Cycle Times - Test and Adjust
CB34 and CC34 Paving Compactors Machine Systems Steering Frame Lock - Separate and Connect
770 and 772 Off-Highway Truck Steering System Oil Sample - Obtain
770 and 772 Off-Highway Truck Suspension Cylinder - Check