Parking Brake Control - Remove and Install
- Put identification marks on all wires and all connectors for installation purposes.
Show/hide table
Illustration 1 g00931527 - Remove cover (1).
Show/hide table
Illustration 2 g00931528 - Remove cotter pin (2). Remove pin (5) and the washer and loosen adjusting nuts (3) in order to disconnect parking brake control cable (4) from the parking brake control.
Show/hide table
Illustration 3 g00931529 - Disconnect electrical wires (6) from the parking brake control. Place identification marks on the electrical wires in order to clearly identify the correct electrical wires that must be connected to the correct terminals for the purpose of installation. Move the electrical wires aside.
Show/hide table
Illustration 4 g00931530 - Loosen bolts (7) and the washers that secure the parking brake control to the frame of the cab. Wind the bolts halfway down the mounting studs in order to allow some movement of the parking brake control.
Show/hide table
Illustration 5 g00931531 - In order to remove the parking brake control, it will be necessary to remove floormat (8). Perform the following steps in order to remove the floormat.
- Remove the steering column. Refer to Disassembly and Assembly Manual, "Steering Column - Remove and Install".
- Remove the seat. Refer to Disassembly and Assembly Manual, "Seat - Remove and Install".
Show/hide table
Illustration 6 g00933021 - Remove harness (9) for the joystick from bulkhead fitting (10).
Show/hide table
Illustration 7 g00933018 - Remove the screws and the washers that secure panel (11) to the cab. It will be necessary to remove the caps from the heads of the screws first. Place the caps in a safe place. Reuse the caps during the installation procedure. Make a note of the location of all the screws and washers for the purpose of installation.
- Dislodge panel (11) from the panel's location in the cab.
Show/hide table
Illustration 8 g00933017 - Remove bulkhead fitting (10) from panel (11).
Show/hide table
Illustration 9 g00932895 - Remove panel (11) from the cab. Move bulkhead fitting (10) aside.
Show/hide table
Illustration 10 g00932894 - Remove stud (12), the guard and the washers from the frame of the cab.
Show/hide table
Illustration 11 g00932893 - Remove handle (13) from the frame of the cab.
Show/hide table
Illustration 12 g00932892 - Remove fuse panel (14) from panel (15).
Show/hide table
Illustration 13 g00932889 - Remove panel (16) from panel (15).
Show/hide table
Illustration 14 g00932888 Show/hide tableIllustration 15 g00932834 - Pull switch panel (17) out of panel (15). Disconnect electrical connectors (19) and electrical wires (18) from the switch panel before removing the switch panel from the cab. Place identification marks on all the electrical connectors and electrical wires in order to identify the correct positions of all the electrical connectors and the electrical wires for the purpose of installation.
Show/hide table
Illustration 16 g00932832 Show/hide tableIllustration 17 g00932833 - Remove retaining nut (21) that secures engine start switch (20) to panel (15). Move the engine start switch aside. Note the orientation of the engine start switch with respect to the markings that identify the different positions of the engine start switch key for the purpose of installation. Refer to the white arrow in Illustration 17.
Show/hide table
Illustration 18 g00932831 Show/hide tableIllustration 19 g00932830 - Pull switch panel (22) out of panel (15). Disconnect electrical connectors (23) from the switch panel before removing the switch panel from the cab. Place identification marks on the electrical connectors in order to identify the correct positions of all the electrical connectors for the purpose of installation.
Show/hide table
Illustration 20 g00932829 Show/hide tableIllustration 21 g00932513 - Pull display (24) out of panel (15). Disconnect electrical connectors (25) from the display before removing the display from the machine. Place identification marks on the electrical connectors in order to identify the correct positions of all the electrical connectors for the purpose of installation.
Show/hide table
Illustration 22 g00932511 - Loosen the clamps that secure hoses (26) in place. Disconnect the hoses from panel (15).
Show/hide table
Illustration 23 g00932503 Show/hide tableIllustration 24 g00932506 Show/hide tableIllustration 25 g00932510 - Remove the screws that secure panel (15) in position. For the locations of the screws, refer to the white arrows in Illustration 24 and Illustration 25. Make a note of the location of the screws for the purpose of installation.
Show/hide table
Illustration 26 g00932499 - Lift the left hand side of panel (15) first before removing the panel from the cab.
Show/hide table
Illustration 27 g00932498 - Remove the screws and the washers that secure panel (27) to panel (28). It will be necessary to remove the caps from the heads of the screws first. Place the caps in a safe place. Reuse the caps during the installation procedure. Make a note of the location of all the screws and washers for the purpose of installation.
- Dislodge panel (27) from the panel's position on top of panel (28). Do not remove panel (27).
Show/hide table
Illustration 28 g00932497 - Remove the screws and the washers that secure panel (28) to the cab. It will be necessary to remove the caps from the heads of the screws first. Place the caps in a safe place. Reuse the caps during the installation procedure. Make a note of the location of all the screws and washers for the purpose of installation.
Show/hide table
Illustration 29 g00940115 - Dislodge the bottom of panel (28) from the side of cab. Move the panel to one side. Do not remove the panel.
Show/hide table
Illustration 30 g00940116 - Remove floormat (8) carefully from the cab. Take care to pull the floormat around the parking brake control.
Show/hide tableIllustration 31 g00932366 - Remove bolts (7) and the washers in order to remove the parking brake control from the underside of the machine.
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 32 g00932366 Show/hide tableIllustration 33 g00932367 - Position the parking brake control to the underside of the machine.
- Install bolts (7) and the washers that secure the parking brake control to the frame of the cab. Install the bolts halfway up the mounting studs for the parking brake control. Do not tighten the bolts at this step in order to give the parking brake control some free movement.
Show/hide table
Illustration 34 g00931531 - In order to remove the parking brake control, it was necessary to remove floormat (8). Perform the following steps in order to install the floormat.
- Install floormat (8) into the cab. Ensure that the pedal for the parking brake control projects through the floormat correctly.
Show/hide table
Illustration 36 g00932497 - Position panel (28) to the cab and secure the panel in place with the screws. Install the caps on the heads of the screws. For the locations of the screws, refer to the note that was made during the removal procedure.
Show/hide table
Illustration 37 g00932498 - Position panel (27) to panel (28) and secure the panel in place with the screws. Install the caps on the heads of the screws. For the locations of the screws, refer to the note that was made during the removal procedure.
Show/hide table
Illustration 38 g00932499 Show/hide tableIllustration 39 g00932500 - Lift panel (15) into the cab. Lower the left hand side of the panel into position. Ensure that the screw hole in the panel fits behind the bracket on the side of the cab. Refer to the white arrow in Illustration 39.
Show/hide table
Illustration 40 g00932503 Show/hide tableIllustration 41 g00932506 Show/hide tableIllustration 42 g00932510 - Completely position panel (15) into the panel's correct position. Secure the panel in place with the screws. For the locations of the screws, refer to the note that was made during the installation procedure and to the white arrows in Illustration 41 and Illustration 42.
Show/hide table
Illustration 43 g00932511 - Connect hoses (26) to panel (15) and secure the hoses in place with the clamps.
Show/hide table
Illustration 44 g00932513 Show/hide tableIllustration 45 g00932829 - Connect electrical connectors (25) to display (24) before fitting the display into panel (15). Refer to the identification marks that were placed on the electrical connectors during the removal procedure in order to identify the correct positions of all the electrical connectors.
Show/hide table
Illustration 46 g00932830 Show/hide tableIllustration 47 g00932831 - Connect electrical connectors (23) to switch panel (22) before fitting the switch panel into panel (15). Refer to the identification marks that were placed on the electrical connectors during the removal procedure in order to identify the correct positions of all the electrical connectors.
Show/hide table
Illustration 48 g00932832 Show/hide tableIllustration 49 g00932833 - Position engine start switch (20) to the rear of panel (15) and secure the engine start switch in place with retaining nut (21). Note the orientation of the engine start switch with respect to the markings that identify the different positions of the engine start switch key. Refer to the white arrow in Illustration 49.
Show/hide table
Illustration 50 g00932834 Show/hide tableIllustration 51 g00932888 - Connect electrical connectors (19) and electrical wires (18) to switch panel (17) before fitting the switch panel into panel (15). Refer to the identification marks that were placed on the electrical connectors and the electrical wires during the removal procedure in order to identify the correct positions of all the electrical connectors and the electrical wires.
Show/hide table
Illustration 52 g00932889 - Install panel (16) into panel (15).
Show/hide table
Illustration 53 g00932892 - Install fuse panel (14) into panel (15).
Show/hide table
Illustration 54 g00932893 - Install handle (13) into the frame of the cab.
Show/hide table
Illustration 55 g00932894 - Install stud (12), the guard and the washers into the frame of the cab.
Show/hide table
Illustration 56 g00932895 - Position panel (11) into the rear of the cab. Do not install the panel into the panel's final position. Leave plenty of room for access in order to install bulkhead fitting (10).
Show/hide table
Illustration 57 g00933017 - Install bulkhead fitting (10) into panel (11).
Show/hide table
Illustration 58 g00933018 Show/hide tableIllustration 59 g00933019 Show/hide tableIllustration 60 g00933020 - Install panel (11) into position in the cab. Note that the rear edge of the panel slips in front of the rear window. Refer to the white arrow in Illustration 59. Also note that the left hand edge of the panel slips behind the post for the door. Refer to the white arrow in Illustration 60.
- Secure panel (11) in place with the screws. Install the caps on the heads of the screws. Note that some of the screws are installed with washers. For the locations of the screws and the location of the screws that are installed with washers, refer to the note that was made during the removal procedure.
Show/hide table
Illustration 61 g00933021 - Install harness (9) for the joystick to bulkhead fitting (10).
- Install the seat. Refer to Disassembly and Assembly Manual, "Seat - Remove and Install".
- Install the steering column. Refer to Disassembly and Assembly Manual, "Steering Column - Remove and Install".
Show/hide tableIllustration 35 g00940116 Show/hide tableIllustration 62 g00931530 - Install floormat (8) into the cab. Ensure that the pedal for the parking brake control projects through the floormat correctly.
- Tighten bolts (7) in order to secure the parking brake control in place.
Show/hide table
Illustration 63 g00931529 - Connect electrical wires (6) to the parking brake control. Use the identification marks that were placed on the wires during the removal procedure to clearly identify the correct wires to connect to the correct terminals.
Show/hide table
Illustration 64 g00931528 - Position parking brake control cable (4) to the parking brake control. Install adjusting nuts (3) in order to temporarily secure the parking brake control cable to the parking brake control. Install pin (5) in order to secure the end of the parking brake control cable to the parking brake control. Install cotter pin (2) in order to secure the pin in place.
- Adjust the positions of adjusting nuts (3) in order to position parking brake control cable (4) correctly. Refer to Systems Operation, Testing and Adjusting, RENR5156, "Braking System", "Parking Brake Control Cable - Adjust".
Show/hide table
Illustration 65 g00931527 - Install cover (1).
Caterpillar Information System:
D350E and D400E Articulated Trucks Power Train Solenoid Valve (Lockup Clutch)
D350E and D400E Articulated Trucks Power Train Lockup Clutch and Solenoid Valve
574B Forwarder Power Train Accelerator Pedal
3054E Industrial Engine Camshaft Bearings - Remove and Install
D350E and D400E Articulated Trucks Power Train Priority Valve
793C and 793C XQ Off-Highway Truck Steering System Steering Linkage and Cylinder Mounting
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine Coolant Temperature Lamp)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine Oil Pressure Lamp)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine ON Signal)
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers MID 039 - CID 0975 - FMI 08
574B Forwarder Power Train Monitoring System
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Disassemble
574B Forwarder Power Train On/Off Switches
CB-634D Paving Compactor Machine Electronic Control System Service Tools
14H Motor Grader Machine Systems Blade Lift Cylinder - Remove and Install
Test Sequence for Capsule Type Fuel Nozzles{0782} Test Sequence for Capsule Type Fuel Nozzles{0782}
14H Motor Grader Machine Systems Wheel Lean Bar - Remove and Install
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070} Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
2002/10/28 Correction to Operation and Maintenance Manual , "Equipment Lowering with Engine Stopped" {7000}
2002/10/21 A Special Instruction, REHS1252, "Field Installation of Body Exhaust Arrangements" Is Available {1061, 7258}
14H Motor Grader Machine Systems Combination Valve - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Pump Control (Output Flow) - Adjust
14H Motor Grader Machine Systems Bank Valve - Remove