Use 1R-1297 Belts With Special Application Drive Wheels
Usage:
AGRICULTURAL TRACTORSCHALLENGER 65B (7YC2094-Up),
CHALLENGER 65C (2ZJ1-Up),
CHALLENGER 75 (4CJ436-Up),
CHALLENGER 75C (4KK1-499) AGRICULTURAL TRACTORS
CHALLENGER 65C (2ZJ1-Up),
CHALLENGER 75 (4CJ436-Up),
CHALLENGER 75C (4KK1-499) AGRICULTURAL TRACTORS
Problem:
In previously published literature, it was indicated that 1R-1232 was the only belt to be used when using Special Application Drive Wheels (SADW).
Solution:
All machines in the affected range above cannot accept the 1R-1232 Belts 762 mm (30 inch), due to insufficient clearance with the frame. When using Special Application Drive Wheels on these machines, use the 1R-1297 Belt 698 mm (27.5 inch). This belt has the same internal features (extra breaker ply and inside protection) as the 1R-1232 Belt 762 mm (30 inch).
COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar Information System:
Ground Speed Calibration Factor May Have Not Been Entered At The Factory Ground Speed Calibration Factor May Have Not Been Entered At The Factory
Procedure To Stop Oil Leaks From Around Engine Breather Cover Procedure To Stop Oil Leaks From Around Engine Breather Cover
Steering Effort May Increase Steering Effort May Increase
108-5933 Ride Control Accumulator 108-5933 Ride Control Accumulator
Machines That Are Equipped With 136-4652 Cleaner Bar Group Have Experienced Finger Loosening Machines That Are Equipped With 136-4652 Cleaner Bar Group Have Experienced Finger Loosening
Incorrect Seal Installation On The Hydrostatic Drive Causes Leaks Incorrect Seal Installation On The Hydrostatic Drive Causes Leaks
Machines Experiencing Brake Overheating Due To Repetitive Braking At High Speed Machines Experiencing Brake Overheating Due To Repetitive Braking At High Speed
Improperly Torqued Hardware On Driveshaft Yokes Improperly Torqued Hardware On Driveshaft Yokes
Compactors May Seem Underpowered When Used In Certain Applications Compactors May Seem Underpowered When Used In Certain Applications
Some 163-1877 (Windshield) Washer Groups Have Been Assembled Incorrectly Some 163-1877 (Windshield) Washer Groups Have Been Assembled Incorrectly
Incorrect Service Literature Incorrect Service Literature
Generator Lead Connections Can Rub Against The Terminal Box Or Each Other Generator Lead Connections Can Rub Against The Terminal Box Or Each Other
Oil Pan Cracking Oil Pan Cracking
Grade Control Valve Contamination Grade Control Valve Contamination
Direct Drive Transmission Front Output (All Wheel Dirve) Shaft Failures Direct Drive Transmission Front Output (All Wheel Dirve) Shaft Failures
Oil In Turbochargers Oil In Turbochargers
Incorrect Engine Arrangement Numbers Shown On Customer Invoices Incorrect Engine Arrangement Numbers Shown On Customer Invoices
Serial Information Number (SIN) Decal Replacement Serial Information Number (SIN) Decal Replacement
9X-4606 Lip Seal May Leak At Torque Converter Output Shaft And Transfer Gear Input 9X-4606 Lip Seal May Leak At Torque Converter Output Shaft And Transfer Gear Input
Hood May Contact Aftercooler Hood May Contact Aftercooler
Certain 145-6035 Duo-Cone Seal Groups Need To Be Inspected And Removed From Dealer Inventory Certain 145-6035 Duo-Cone Seal Groups Need To Be Inspected And Removed From Dealer Inventory
Torque Converter Turbine Rubbing And Wear Torque Converter Turbine Rubbing And Wear
Logged Service Codes Are Erased On Certain Monitoring System Modules When The Key Switch Is Turned Off Logged Service Codes Are Erased On Certain Monitoring System Modules When The Key Switch Is Turned Off
Incorrect Muffler Extensions May Have Been Shipped With Machines Incorrect Muffler Extensions May Have Been Shipped With Machines