Usage:
17Jul2017 |
L120
M666
Q300
Q302
Q310
Q312
R050
R120
Z800
After Failure Only (Limited distribution) | PRODUCT SUPPORT PROGRAM FOR REWORKING THE RADIATOR FAN ON CERTAIN 3512 AND 3516 GENERATOR SETS |
|
1356 | PS53519 |
NOTE: | Caterpillar’s obligations under this Service Letter are subject to, and shall not apply in contravention of, the laws, rules, regulations, directives, ordinances, orders, or statutes of the United States, or of any other applicable jurisdiction, without recourse or liability with respect to Caterpillar. |
NOTE: | This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS53519" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code. |
NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst. |
TERMINATION DATE |
31Jul2019 |
PROBLEM
The blades on the existing radiator fan assembly may become loose and/or fracture on certain 3512, 3512B, and 3516B Generator Sets. |
AFFECTED PRODUCT
Model | Identification Number |
3512 | ZAF00338-00339 |
3512B | YAM00309-00311, 442-443, 445-446, 726 YAY00326, 329-330, 332-333, 336, 339, 344, 348, 351-353, 362, 367, 520-521, 526 ZAH00178-00179, 182, 256, 265, 533, 579, 591, 654, 662, 770, 774 |
3516B | YAP00345, 360, 362 |
PARTS NEEDED
Qty |
Part Number | Description |
6 | 7X0325 | BOLT |
1 | 5297264 | FAN AS. - RADIATOR |
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 2% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. |
ACTION REQUIRED
Important Safety Information Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly. Safety precautions and warnings are provided in this instruction, on the product, and in this product's Operation and Maintenance Manual (OMM). If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication, the warnings that are on the product, and the warnings that are in the OMM are not all inclusive. If a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar is used, the user must ensure that it is safe for the user and for other people to use. The user should ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used. WARNING: The generator set must be isolated electrically before and while the rework is performed. Follow the proper lockout tag out procedures to protect against the unexpected energizing or startup of the generator set. Failure to follow these warnings could result in injury to personnel during service. Attach a "Do Not Operate" warning tag to the machine start switch or the controls before you perform any service to the machine. Repair Action Required At the next scheduled maintenance, inspect the 242-4243 Fan for blade loosening. Check looseness by placing a dial indicator at edge of the blade tip in the location shown in Image1. Grab the blade at the tip and gently move the blade up and down in the direction shown by the arrows in Image2. Inspect the joint where the composite blade attaches to the aluminum hub as shown in Image3. If total blade movement greater than 6 mm is measured as a result of movement at this joint, then replace the fan with 529-7264 Radiator Fan. To install the 529-7264 Radiator Fan, the existing mounting bolts will need to be replaced with 7X-0325 Bolts since the hub is approximately 1/2 inch (13 mm) thicker. Tighten mounting bolts to 105 +/- 20 N-m. Refer to Disassembly and Assembly, RENR5060 for the radiator fan disassembly and assembly instructions. |
Image1 |
Image2 |
Image3 |
SERVICE CLAIM ALLOWANCES
0-144 mo |
NOTE: This is a 7.0-hour job | ||||||
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |