PRODUCT SUPPORT PROGRAM FOR REPAIRING THE ENGINE JACKET WATER LINE LEAKS ON CERTAIN PMG3516C (XQ1475G) POWER MODULES Caterpillar

PRODUCT SUPPORT PROGRAM FOR REPAIRING THE ENGINE JACKET WATER LINE LEAKS ON CERTAIN PMG3516C (XQ1475G) POWER MODULES

Usage:

TEBE3424-00

Show/hide table

22Jul2015

B94N
D35P

Show/hide table

Before/After (Limited distribution)	PRODUCT SUPPORT PROGRAM FOR REPAIRING THE ENGINE JACKET WATER LINE LEAKS ON CERTAIN PMG3516C (XQ1475G) POWER MODULES
1380		PS44806

Show/hide table

NOTE:

Caterpillar’s obligations under this Service Letter are subject to, and shall not apply in contravention of, the laws, rules, regulations, directives, ordinances, orders, or statutes of the United States, or of any other applicable jurisdiction, without recourse or liability with respect to Caterpillar.

NOTE:

This Program must be administered either before or after failure. In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS44806" as the Part Number and "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.

Show/hide table

NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

Show/hide table

TERMINATION DATE

31Jul2017

PROBLEM

Show/hide table

The existing engine jacket water (JW) line joint utilizing the 4S-0405 Joint Assembly can have reduced seal life and leak on certain PMG3516C (XQ1475G) Power Modules.

AFFECTED PRODUCT

Show/hide table

Model	Identification Number
PMG3516C	JKK00103, 110-111, 118, 133, 146, 150, 163, 165, 167, 170-171, 174, 183-185, 188-189, 210

PARTS NEEDED

Show/hide table

Qty	Part Number	Description
2	2617954	SEAL
2	3662715	COOLANT-ENGINE
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 32% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table

Refer to the Service Manual if/as necessary.
Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.

A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.

Safety precautions and warnings are provided in this instruction, on the product, and in this product's Operation and Maintenance Manual (OMM). If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.

Therefore, the warnings in this publication, the warnings that are on the product, and the warnings that are in the OMM are not all inclusive. If a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar is used, the user must ensure that it is safe for the user and for other people to use.

The user should ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.

WARNING: The generator set must be isolated electrically before and while the rework is performed. Follow the proper lockout tag out procedures to protect against the unexpected energizing or startup of the generator set. Failure to follow these warnings could result in injury to personnel during service. Attach a "Do Not Operate" warning tag to the machine start switch or the controls before you perform any service to the machine.

Rework Action Required

There is one affected joint on the JW line that will need to be repaired (4S-0405 Joint Assembly). Refer to Image1.

When repairing the jacket water line joint utilizing the 4S-0405 Joint Assembly, verify tube alignment, and replace the two 9X-7538 Seals with two 216-7954 Seals.

Refer to the attached Rework Procedure.

Show/hide table

Image1

SERVICE CLAIM ALLOWANCES

Show/hide table

Product smu/age whichever comes first	Caterpillar		Dealer Suggested		Customer Suggested
Product smu/age whichever comes first	Parts %	Labor Hrs%	Parts %	Labor Hrs%	Parts %	Labor Hrs%
0-20000 hrs, 0-60 mo	100.0%	100.0%	0.0%	0.0%	0.0%	0.0%

Show/hide table

NOTE: This is a 2.0-hour job

Show/hide table

PARTS DISPOSITION

Show/hide table

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

Rework Procedure

Show/hide table

Drain engine coolant and retain for re-fill later.

Check tube alignment. The fitting must have +/- 4 degrees or less angular misalignment. Refer to Image1.1.1.

As an alternate method to measure alignment, the maximum angular misalignment corresponds to a maximum pipe offset value of 12 mm. Note that a straight edge can be used with the fitting removed. The offset distance should be measured at the point corresponding to the end of the fitting to take in to account any angular misalignment of the pipe. Refer to Image1.2.1.

Image1.1.1

Image1.1.2

Deburr and clean pipe ends. Surface should be free of deep scratches, gouges, dents, dirt, etc. Visually check roundness of pipe. A proper seal may be comprised if the roundness of the pipe is distorted.

Install retainer (1), gasket (2) and sleeve (3) on one side of pipe in the sequence shown. Assembly of gaskets can be made easier by dipping gaskets in water or the fluid to be sealed. The use of other rubber lubricants can be detrimental to the life of the gaskets. Never lubricate the metal parts. Install remaining retainer (4) and gasket (5) on other pipe end. Position retainer (4) and gasket (5) to proper pipe insertion depth ("D" = 33.7 mm minimum to 61.5 mm maximum). Refer to Image1.2.1.

Slide sleeve (3) to gasket (5) and move gasket (2) and retainer (1) into position. Pipe must be inserted to proper depth ("D" = 33.7 mm minimum to 61.5 mm maximum) into both gaskets. Refer to Image1.2.2.

Install both V-couplings, encompassing the retainer, gasket and sleeve. Do not tighten either coupling until the entire joint is assembled. The final torque value for the nuts is 28 +/- 0.5 N-m. Refer to Image1.2.3.