Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Usage:
All Caterpillar Cylinder Heads
When the cylinder head is reconditioned, inspect the seat for the precombustion chamber or D. I. adapter. If the seat is pitted or damaged, make a repair; see the instructions that follow.
(1) Install the correct FT1766 Pilot Adapter (1) in hole (2), until the top of the pilot adapter is 5.0 (.2") below the seat surface.
(2) Install 9.525Ø (.375"Ø) pilot (3) in adapter (1). Use a flat bottom grind stone (4) and holder (5), with a high speed driver, to remove pitting or damage from the seat surface. Remove as little material as possible, to keep dimension (A) to a maximum.
(3) Remove the flat stone and use a 45° stone (6) to grind a chamfer (B) to the original dimension.
Caterpillar Information System:
Installation Of Electric Wiper Motors{7300, 7305} Installation Of Electric Wiper Motors{7300, 7305}
Using The 6V7899 Size Setting Fixture Group{651} Using The 6V7899 Size Setting Fixture Group{651}
Use Of 6V7898 Dial Bore Gauge Group{0761} Use Of 6V7898 Dial Bore Gauge Group{0761}
Installation Of Altronic III Ignition Conversion Groups{1550, 1552, 1567} Installation Of Altronic III Ignition Conversion Groups{1550, 1552, 1567}
Installation Of 2W3815 Or 5N93 Inserts{1217} Installation Of 2W3815 Or 5N93 Inserts{1217}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055} Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055}
Installation Of 3N5620 Spacer Group Or 3N5573 Spacer Assembly{3252} Installation Of 3N5620 Spacer Group Or 3N5573 Spacer Assembly{3252}
Installation Of 5N617 Enclosure Group For Package Generator Sets{7002} Installation Of 5N617 Enclosure Group For Package Generator Sets{7002}
Installation Of 1W4259 Valve Spring{1108} Installation Of 1W4259 Valve Spring{1108}
Operation, Maintenance, Troubleshooting And Repair Of 6V4135 Automatic Halogen Gas Leak Detector{0774} Operation, Maintenance, Troubleshooting And Repair Of 6V4135 Automatic Halogen Gas Leak Detector{0774}
Use Of 6V7028 Spring Seat Enlarger For 3200 Cylinder Heads{1101} Use Of 6V7028 Spring Seat Enlarger For 3200 Cylinder Heads{1101}
Use Of 6V7050 Lifter Spring Compressor Group{0622} Use Of 6V7050 Lifter Spring Compressor Group{0622}
Use Of 6V7762 Dual Hook Hoist And Installation Of 6V7919 Conversion Group{641} Use Of 6V7762 Dual Hook Hoist And Installation Of 6V7919 Conversion Group{641}
Use Of 6V7061 Battery Cable Crimping Die{0709, 0710, 1400} Use Of 6V7061 Battery Cable Crimping Die{0709, 0710, 1400}
Installation Of Replacement Cylinder Head Groups (Non-Turbocharged){1101} Installation Of Replacement Cylinder Head Groups (Non-Turbocharged){1101}
Use Of 6V9050 Exhaust Stud Removal Group{1100} Use Of 6V9050 Exhaust Stud Removal Group{1100}
Discharge Recommendations For Gas Operated Counterbalance Support Assemblies{7250, 7300} Discharge Recommendations For Gas Operated Counterbalance Support Assemblies{7250, 7300}
Special Handling Information And Installation Procedure For 4W2568, 4W2569, 4W2570 And 4W2571 Crankshaft Seal Conversion Groups And 4W2606 Or 4W2607 Crankshaft Seal Group{1160, 1161, 1202} Special Handling Information And Installation Procedure For 4W2568, 4W2569, 4W2570 And 4W2571 Crankshaft Seal Conversion Groups And 4W2606 Or 4W2607 Crankshaft Seal Group{1160, 1161, 1202}
Installation Of 6V9068 Repair Kit{0708, 1315} Installation Of 6V9068 Repair Kit{0708, 1315}
Installation of 5N5930 Fuel Injection Lines Group And 2W1788 Fuel Lines Drain Group{1250, 1252} Installation of 5N5930 Fuel Injection Lines Group And 2W1788 Fuel Lines Drain Group{1250, 1252}
Installation Of 5N5340, 2W3536 And 2W3537 Fuel Injection Lines Groups And 2W5100 Fuel Lines Drain Group{1250, 1252} Installation Of 5N5340, 2W3536 And 2W3537 Fuel Injection Lines Groups And 2W5100 Fuel Lines Drain Group{1250, 1252}
Installation Of 8T814 Gauge{0615} Installation Of 8T814 Gauge{0615}
Preparation And Use Of 6V6015 Hose Cutoff Machine{0678} Preparation And Use Of 6V6015 Hose Cutoff Machine{0678}