3406C (PEEC III) DIESEL TRUCK ENGINE Caterpillar


2.0 Programming Parameters

Usage:

Certain parameters that effect PEEC III engine operation may be changed through electronic service tools. The parameters are stored in the ECM, NOT the personality module. Any parameter can be read, but passwords protect parameters from unauthorized changes.

The parameters fall into two catagories: System Configuration Parameters, and Customer Specified Parameters. System Configuration Parameters can be changed only with the proper factory passwords, and Customer Specified Parameters can be changed only with the proper customer passwords. See the following section on passwords for more details on how to get and use passwords.

For details on how to read and change parameters using an ECAP refer to Special Instruction Form No. SEHS9349 if using the NEXG4522 Truck Engine Functions Dual Service Program Module. For the DDT refer to Special Instruction Form No. SEHS8743 if using the NEXG4508 3406C PEEC III Service Program Module.

Connecting ECAP or DDT to PEEC III


1This is a subscription, since it is anticipated that it will be changin g at regular intervals.

The Electronic Control Analyzer Programmer (ECAP) and Digital Diagnostic Tool (DDT) are powered by the 12 volts DC from the vehicle battery. This permits operation on the ground or in the cab of a truck, which allows taking readings during vehicle operation. Use the following procedures to connect the service tool to the engine:

A. The ECAP or DDT may be connected to the PEEC III system at J8, the 9-pin, gray plastic, Deutsch brand connector labeled Engine Data Link Connector. Only one side of the "T" harness connector cable is used. Remove the cap on J8 and replace once testing has been completed.

B. Connect the opposite end of the "T" cable to the ECAP or DDT.

C. The ECAP or DDT will operate with the engine running, or with the engine off, key on. If the ECAP or DDT does not communicate with PEEC III, refer to P312; ECAP/DDT will not communicate with PEEC III.

System Configuration Parameters

System Configuration Parameters are those that affect emissions or horsepower of the engine. They are programmed at the factory and would normally never need to be changed through the life of the engine. Proper values for these parameters are stamped on the engine information ratings plate located on the valve cover or intake manifold. Factory Passwords are required to change these parameters. Figure 1. on page 20 is an example of the ECAP screen displaying System Configuration Parameters. The following is a brief description of the System Configuration Parameters:

Full Load Setting:

Number representing fuel system adjustment made at the factory to "fine tune" the fuel system. Correct value for this parameter is stamped on the engine information ratings plate.

Full Torque Setting:

Similar to Full Load Setting.

Personality Module Code:

Code which prevents use of incorrect personality module for this engine. Each horsepower family and emission certification has a different code associated with it. This code (stored in ECM) MUST match that in the personality module or a Diagnostic Code 56 will be generated and the engine will only run at low idle. When rerating or installing a new ECM, programming this code to "0" will prompt the ECM to read and match its stored code to the personality module. Note that this code DOES NOT need to be programmed when a personality module is replaced, as long as the new module is of the same family. If the PM is of a different family, then pistons, nozzles, etc. may need to be changed and the engine information plate should also be changed to reflect the rerate.

Engine Serial Number:

Should be programmed to match the engine serial number stamped on the ratings plate. A new ECM is delivered with the engine serial number programmed to 0XX00000.

Customer Specified Parameters

Customer Specified Parameters allow a customer to restrict how a driver operates the vehicle. Some parameters may affect engine operation in ways that the inadequately trained driver does not expect. These parameters may lead to power or performance complaints, even when the engine is performing to specification.

For detailed instructions on how to program PEEC III for optimum performance and fuel economy, refer to LEKT8467, Specing for Peak Performance.

Customer parameters may be changed repeatedly as a customer changes his operation or as new drivers are assigned to a truck. Customer Passwords are required to change these parameters. Figure 2. on page 20 is an example of the ECAP screen displaying Customer Specified Parameters. The following is a brief description of the Customer Specified Parameters. Along with each are the minimum and maximum values for the parameter and the default value. The parameter value shown in bold is the setting which should be programmed if the feature is not used.

Vehicle Speed Parameters

Vehicle Speed Cal:

Maximum 65,535 ppm

Minimum 1,717 ppm

Default 858 ppm

Used by the ECM to scale vehicle speed reading into miles per hour. Programmed in pulses per mile. For more information refer to P-504; Vehicle Speed Calibration, it this manual.

Vehicle Speed Limit (VSL):

Top vehicle speed the ECM will permit. The ECM will shut off fuel above this speed.

Maximum 127 mph and/or gear limit of truck

Minimum 30 mph

Default 127 mph

Engine RPM at VSL:

RPM that engine will turn at programmed Vehicle Speed Limit (VSL). The ECM will limit to this RPM only when it sees no vehicle speed signal, and the engine is loaded. This is a tamper proofing feature against running without a Vehicle Speed input to the ECM.

Maximum 3,000 rpm

Minimum 1,300 rpm

Default 3,000 rpm

Cruise Control Parameters

Low Cruise Limit:

The lowest mph at which cruise can be engaged.

Maximum 127 mph

Minimum 15 mph

Default 15 mph

High Cruise Limit:

The highest mph at which cruise can be engaged.

Maximum 127 mph

Minimum 30 mph

Default 127 mph

Engine Retarder Mode:

With the cruise control On/Off switch On, the operation of the retarder is controlled through the customer parameter "Engine Retarder Mode". Programming the parameter to "Coast" allows retarding with the service brakes applied, but allows the engine to coast with no retarding after they are released. Programming the parameter to "Latch" allows retarding with the service brakes applied and keeps the retarder latched On after the service brakes are released (until rpm drops below 950 rpm or the driver presses the throttle or clutch pedal).

With the cruise control On/Off switch in the Off position, the retarder is enabled when the engine rpm is greater than 950 rpm and the drivers foot is off the throttle pedal and clutch pedal.

Refer to P-517: Retarder Enable Signal for more detail on information and operation.

PTO Governor Parameters

PTO Mode Speed Limit:

Maximum mph for PTO mode.

Maximum 15 mph

Minimum 1 mph

Default 1 mph

PTO Mode RPM Limit:

Maximum engine rpm in PTO mode.

Maximum 3,000 rpm

Minimum 600 rpm

Default 3,000 rpm

Progressive Shifting Parameters

Low Gears #1 RPM Limit:

Engine rpm limited below "Low Gear #1 Turn Off Speed. PEEC III will pause at this rpm, then allow slow acceleration up to Top Engine Limit. This is to encourage the driver to shift to the next highest gear.

Maximum 3,000 rpm

Minimum 1,100 rpm

Default 3,000 rpm

Low Gears #1 Turn Off:

Vehicle Speed where "Low Gears #1 RPM Limit" turns off. This must be matched with "Low Gear #1 RPM Limit" to the specific drive train for best performance.

Maximum 30 mph

Minimum 3 mph

Default 3 mph

Low Gears #2 RPM Limit:

Similar to "Low Gears #1 RPM Limit". Typically programmed to slightly higher rpm.

Maximum 3,000 rpm

Minimum 1,100 rpm

Default 3,000 rpm

Low Gears #2 Turn Off:

Similar to "Low Gears #1 Turn Off". Typically programmed to a slightly higher vehicle speed.

Maximum 50 mph

Minimum 5 mph

Default 5 mph

High Gear RPM Limit:

Engine RPM Limit when vehicle speed is above "High Gear Turn On Speed". This is a "hard" limit: PEEC III will not power the engine above this limit. This is to encourage the driver to shift up into overdrive or top gear.

Maximum 3,000 rpm

Minimum 1,300 rpm

Default 3,000 rpm

High Gear Turn On Speed:

Vehicle Speed where "High Gear RPM Limit" turns on. This must be matched to the specific drive train for best performance.

Maximum 127 mph

Minimum 30 mph

Default 127 mph

Engine Parameters

Rating Number:

Number of rating within horsepower family. The personality module defines the horsepower family (such as 350 hp) and may contain several ratings within that family. The rating number defines which rating is used (such as 350 hp @ 1900 rpm or 330 hp @ 1700 rpm) within the family.

Top Engine Limit:

Maximum engine RPM when the engine is under load. The engine will still achieve Rated RPM under no load conditions.

Maximum Rated rpm + 20 rpm

Minimum Rated rpm - 79 rpm

Default Rated rpm + 20 rpm

Low Idle RPM:

Minimum engine RPM which may be programmed to any value between 600 RPM to 750 RPM range.

Maximum 750 rpm

Minimum 600 rpm

Default 750 rpm

Idle Shutdown Time:

Time (in minutes) that engine will idle before shutting down (between 3 and 60 minutes). Engine will only shutdown if PEEC III sees no engine load, no vehicle speed, and the park brake is set. If this parameter is programmed to zero, this feature is disabled and the engine will idle until the key switch is turned OFF.

Maximum 60 min

Minimum 3 min

Default 0 min

Engine Protection Parameters

Engine Protection Mode:

Determines the level of action taken by the ECM in response to a potentially engine damaging condition recognized by the Caterpillar Coolant Temperature, Oil Pressure, or OEM Coolant Level (if installed and enabled)

Default WARNING

Alternative OFF

Alternative DERATE

Alternative SHUTDOWN

Coolant Level Sensor Enable/Disable:

Determines if the ECM monitors the Coolant Level Sensor inputs.

Default ENABLED

Alternative DISABLED

Passwords

Factory Passwords

Factory passwords are required to perform each of the following four functions:

1. Program a New ECM

When an ECM is replaced, the System Configuration Parameters must be programmed into the new ECM. These parameters are protected by factory passwords.

2. Rerate Engine to another Engine Family

This requires changing the personality Module Code, which is protected by factory passwords.

3. Read Customer Passwords

If the owner loses his customer passwords, he will not be able to program customer parameters. Using factory passwords, one can read customer passwords, then use those customer passwords to program customer parameters.

4. Clear Certain Diagnostic Codes

Only Diagnostic Codes 190-00 (Engine Overspeed Warning) and 23-02 (Excessive Engine Power) require factory passwords to clear once they are logged. Certain other codes require customer passwords. The majority of logged codes require no passwords to clear.

Since factory passwords contain alphabetic characters, only the ECAP may perform these functions. The DDT cannot because it hasn't any alphabetic character keys.

To obtain factory passwords, proceed as if you already had the password. At some point, if factory passwords are truly needed, the ECAP will request factory passwords and will provide on its screen most of the information required to obtain the passwords.

Customer Passwords

Customer passwords are required to change ANY customer parameter. Customer Parameters are those that effect vehicle speed limits, horsepower rating within a family, and PTO operation. See the previous section on "Customer Specified Parameters" for more detail on what parameters are customer programmable.

Either the ECAP or DDT may change Customer Parameters (although if a customer uses alphabetic characters in his password, only the ECAP can change Customer Parameters).

To obtain customer passwords, contact the owner of the vehicle. If the owner has lost his passwords, customer passwords may be read using an ECAP (factory passwords are required in order to read the customer passwords) by following these steps:

A Use the ECAP to access "Read/Change System Configuration Parameters", then "Read Customer Parameters".

B. When the Factory Passwords screen appears, record the information listed on the "PEEC III Factory Passwords Worksheet" (in this section).

C. Obtain the factory passwords. The information recorded above must be provided, and generates a permanent record at Caterpillar of the access.

D. From the Factory Passwords screen, enter the Factory Passwords.

E. When the "Read Customer Passwords" screen appears, record the Customer Passwords. The Customer Passwords may then be used to change Customer Parameters.

Programming a New ECM

The PEEC III Electronic Control Module or ECM is the heart of the system. So when a problem occurs, it is easy to jump to the conclusion that the ECM is responsible. That is usually the wrong conclusion. There are no moving parts inside, therefore, the ECM very seldom fails.

Most failures occur at a sensor input/output, or in the wiring and connectors. Follow the troubleshooting guide procedures, and don't replace an ECM on speculation!

However, when your troubleshooting indicates that a failure has, in fact, occurred in the ECM, then temporarily hang a new ECM on the side of the engine and thoroughly Retest. If the problem is no longer present then proceed with the following steps required to permanently replace a faulty ECM.

ECM Replacement Procedure

1. Record customer parameters from failed ECM.

NOTE: If ECAP is unable to communicate with the ECM, go to Step 2.

A. Obtain and record the Customer Passwords. If the customer (owner) has lost or forgotten his passwords, go to "Customer Passwords" in this section.

B. Use the ECAP to access "Read Customer Specified Parameters" from the ECM being replaced.

C. Use the "PEEC III Customer Specified Parameters Worksheet" (in this section), to record the customer parameters.

2. Replace the faulty ECM.

3. Obtain Factory Passwords.

A. Using the "PEEC III Factory Passwords Worksheet" (in this section), Record the following information from the engine information plate: Full Load Setting, Full Torque Setting, Engine Serial Number.

B. Record the mileage from the vehicle odometer.

C. Use the ECAP to access "Read/Change System Configuration Parameters". When the Factory Specified Passwords screen appears, record the following information: ECM serial number, Engine serial number, ECAP serial number, and Total Tattletales.

D. Leave the ECAP on the Factory Specified Passwords screen and obtain the Factory Passwords by providing the information listed on the "PEEC III Factory Passwords Worksheet".

4. Program the new ECM.

A. Use the ECAP to access "Read/Change System Configuration Parameters". Enter the Factory Passwords into the Factory Specified Passwords screen. Enter the Full Load Setting, Full Torque Setting, and Engine serial number recorded on the worksheet. Program the Personality Module Code to 0 before leaving this screen.

B. Use the ECAP to access "Read/Change Customer Specified Parameters". Enter the Customer Specified Parameters and the original Customer Passwords recorded on the worksheet.

C. Use the ECAP to access "Calibrate/Monitor Sensors", and calibrate the boost sensor.

NOTE: If the Customer Specified Parameters are entered before the System Configuration Parameters, the Total Tattletales will change. It will then be necessary to obtain another set of Factory Passwords to access "Read/Change System Configuration Parameters".

ECAP Screen: "System Configuration Parameters"


Figure 1.

ECAP Screen: "Customer Specified Parameters"


Figure 2.

Caterpillar Information System:

3406C (PEEC III) DIESEL TRUCK ENGINE 1.0 PEEC III Electronic System Overview
SUPPLEMENT FOR - 3176 REAR POWER TAKE-OFF (RPTO) Rear Power Take-Off (RPTO)
SUPPLEMENT FOR - 3176 REAR POWER TAKE-OFF (RPTO) Testing And Adjusting
SUPPLEMENT FOR - 3176 REAR POWER TAKE-OFF (RPTO) Systems Operation
SUPPLEMENT FOR - 3176 REAR POWER TAKE-OFF (RPTO) Rear Power Take-Off Gear Group (RPTO)
ELECTRONIC MODULAR CONTROL PANEL II (EMCP II) Schematics & Wiring Diagrams
ELECTRONIC MODULAR CONTROL PANEL II (EMCP II) Testing And Adjusting
ELECTRONIC MODULAR CONTROL PANEL II (EMCP II) Systems Operation
ELECTRONIC MODULAR CONTROL PANEL (EMCP) FOR RENTAL GENERATOR Schematics & Wiring Diagrams
ELECTRONIC MODULAR CONTROL PANEL (EMCP) FOR RENTAL GENERATOR Testing And Adjusting
ELECTRONIC MODULAR CONTROL PANEL (EMCP) FOR RENTAL GENERATOR Systems Operation
ELECTRONIC MODULAR CONTROL PANEL (EMCP) FOR RENTAL GENERATOR Symbols
3406C (PEEC III) DIESEL TRUCK ENGINE 3.0 Troubleshooting without a Diagnostic Code
3406C (PEEC III) DIESEL TRUCK ENGINE 4.0 Troubleshooting with a Diagnostic Code
3406C (PEEC III) DIESEL TRUCK ENGINE 5.0 Electronic Subsystem Functional Tests
3406C (PEEC III) DIESEL TRUCK ENGINE 6.0 Glossary Of PEEC III Terms
3406C Electronic Diesel Truck Engine Electrical System 3406C Electronic Diesel Truck Engine Electrical System
3406C (PEEC III) TRUCK ENGINE Introduction
3406C (PEEC III) TRUCK ENGINE Tools Required
3406C (PEEC III) TRUCK ENGINE Test Procedure
3406C (PEEC III) TRUCK ENGINE 3406C (PEEC III) Truck System Tests Not Covered by the Volt-Ohm Meter
3406C (PEEC III) TRUCK ENGINE Correct Adjustment of the Throttle Linkages
3406C (PEEC III) TRUCK ENGINE Responsibility for Throttle Pedal Adjustment
3406C (PEEC III) TRUCK ENGINE Visual Inspection and Repair of Connectors
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.