3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Caterpillar


Water Pump (Earlier)

Usage:


Water Pump (Earlier)

Disassemble Water Pump (Earlier)

START BY:

a. remove water pump

1. Hold shaft (1) with a wrench, and use an impact wrench to remove the nut from the other end of the shaft.

2. Remove adapter (2) from the shaft.

3. Remove screws (3) and retainer (4) from the housing.

4. Use tooling (A) and a press as shown to remove shaft (1), seal assembly and impeller (6) from housing (5).

5. Remove bearing (5) from the housing.

NOTE: Use tooling (B) to remove bearing (5) if it is tight in the housing.

6. Remove spacers (7) and (8) from the housing.

7. Remove bearing (9) from the housing.

8. Use tooling (C) and a press to remove shaft (1) from the impeller.

9. Install shaft (1) and seal assembly (10) in housing (5) as shown. Use tooling (C) and a press to remove shaft (1) from seal assembly (10).

10. Use a hammer and punch to remove the seal assembly from housing (5).

Assemble Water Pump (Earlier)

1. Install the inner bearing in the housing with notch (2) in the bearing in alignment with notch (1) in the housing.

2. Install spacer (3) in the housing with the pin in the spacer in alignment with notch (1) in the housing and the notch in the bearing. The pin in the spacer prevents rotation of the outer bearing race.

3. Install spacer (4) and bearing (5) in the housing. Use tooling (B) and a press to install bearing (5) if necessary.

4. Put retainer (6) in position on the housing, and install the screws that hold it in place.

5. Install shaft (7) in the housing as shown.

6. Install adapter (8) on the shaft as shown.

7. Put 9S3263 Thread Lock on the threads of shaft (7), and install the nut on the shaft.

8. Hold adapter (8) in a vise that has soft jaws.


NOTICE

Use extra care not to damage adapter (8) when it is held in a vise.


9. Use wrench (9) and adapter (8) in a vise to hold the shaft while the nut on the shaft is tightened to a torque of 200 ± 20 N·m (150 ± 15 lb.ft.).

10. Install seal assembly (10) into the housing with tool (C) and a press. Do not use a hammer.

11. Install 5P7350 Spacer (12) as shown. Put impeller (13) in position on the shaft. Use 5P7353 Spacer (11) and a press to push impeller (13) on the shaft until spacer (12) can just be removed between the impeller and housing. The 5P7350 and 5P7353 Spacers are both part of tooling (A).

NOTE: If spacer (12) cannot be removed, do the following steps:

a. Remove adapter (8) from the water pump.

b. Use tooling (B) and a press to push the shaft from the adapter side of the water pump until the spacer can be removed.

c. Put 9S3263 Thread Lock on the threads of the shaft. Install the adapter and nut on the shaft. Tighten the nut to a torque of 200 ± 20 N·m (150 ± 15 lb.ft.) as shown in Step 9.

END BY:

a. install water pump

Caterpillar Information System:

3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Water Pump
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Water Temperature Regulator
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Radiator And Guard Assembly
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Radiator
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fan Drive
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fan Belts
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fan
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Valve Lifters
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Cylinder Head Assembly
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Rocker Shaft Assembly
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Rocker Shaft Assembly And Push Rods
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Valve Cover (Later)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Water Pump (Later)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Tank
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Transfer Pump (Earlier Interim Scroll Fuel System)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Transfer Pump (Later Interim Scroll Fuel System)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Transfer Pump (New Scroll Fuel System Effective In Production With 10X5411-UP, 45V36536-UP)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Governor Control
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Injection Lines (Interim Scroll Fuel System)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Injection Lines (New Scroll Fuel System Effective In Production With 10X5411-UP, 45V36536-UP)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Filter And Base
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Injection Nozzles (New Scroll Fuel System Effective In Production With 10X5411-Up, 45V36536-Up)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Injection Nozzles (Interim Scroll Fuel System)
3204 VEHICULAR ENGINE FOR 943 & 953 TRACK-TYPE LOADERS Fuel Injection Pump Housing And Governor (Interim Scroll Fuel System)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.