3406B (PEEC) DIESEL TRUCK ENGINE Caterpillar


Oil Pump (BrakeSaver)

Usage:

Remove And Install Oil Pump (BrakeSaver)

Start By:

a. remove oil pan (BrakeSaver)

1. Remove suction bell (3) and tubes, oil supply tube (2) and BrakeSaver oil supply tube (1) from the engine block and oil pump.

2. Remove three bolts (5) and oil pump (4) from the engine.

NOTE: The following steps are for the installation of the oil pump.

3. Put oil pump (4) in position on the engine. Make sure the oil pump gear is engaged with the crankshaft gear, and install three bolts (5) that hold the oil pump.

4. Put clean engine oil on the O-ring seals on the oil tubes.

5. Install suction bell (3) and tubes, oil supply tube (2) BrakeSaver oil supply tube (1).

End By:

a. install oil pan (BrakeSaver)

Disassemble Oil Pump (BrakeSaver)

Start By:

a. remove oil pump (BrakeSaver)

1. Remove the bolt and washer that hold drive gear (1) on the shaft.

2. Use tooling (A) to remove drive gear (1) from the shaft. Remove the key from the shaft. Put alignment marks on the pump bodies so they can be assembled in the correct position.

3. Remove retainer (3) from the bypass valve. Remove the spring and bypass valve.

4. Remove bolts (4) that hold pump body (2) to the main pump body. Remove pump body (2).

5. Use tooling (B) to remove the bearings from pump body (2).

6. Remove gears (7). Put identification marks on the gears so they can be assembled in the same position.

7. Remove spacer (6) from the main oil pump body (5). Use tooling (B) to remove the bearings from spacer (6).

8. Remove the gears from main oil pump body (5).

9. Use tooling (B) to remove the bearings from the main oil pump body.

Assemble Oil Pump (BrakeSaver)

1. Use tooling (B) to install bearings (8) until they are even with the outside surface of main oil pump body (5). Install bearings (8) so the joints in the bearings are 30° ± 15° from the center line of the bearing bores and toward the oil pump outlet passage as shown.

2. Use tooling (B) to install bearings (9) in the spacer. Install the bearings until they are in position an equal distance in from each side of the spacer. Install the bearings with the oil holes in the bearings in alignment with the oil holes in the spacer and the joints in the bearings in alignment with the cavity on the spacer as shown.

3. Put clean engine oil on all the gears and bearings before they are assembled in the oil pump. Install idler and drive gears (10) in the main oil pump body.

4. Install spacer (6) on the gear shafts with the smaller cavity out and the oil holes in the spacer toward the pump outlet passage as shown.

5. Use tooling (B) to install bearings (11) in pump body (2) until they are 1.52 ± 0.25 (.060 ± .010 in.) from the inside edge of the bearing bores. Install the bearings so the joints in the bearings are 30° ± 15° from the centerline of the bearing bores and toward the outer passage. The outlet passage has a cavity between the bearing bores.

6. Install pump gears (7) on the oil pump shafts in their original position.

7. Install pump body (2). Install bypass valve (12), spring (13), and retainer (3).

8. Install the key on the shaft.

9. Install gear (1) on the shaft. Install the washer and bolt that holds the gear on the shaft. Be sure the pump turn freely after assembly.

End By:

a. install oil pump (BrakeSaver)

Caterpillar Information System:

3406B (PEEC) DIESEL TRUCK ENGINE Oil Pan (BrakeSaver)
3406B (PEEC) DIESEL TRUCK ENGINE BrakeSaver
3406B (PEEC) DIESEL TRUCK ENGINE BrakeSaver Control Valve
3406B (PEEC) DIESEL TRUCK ENGINE Flywheel (BrakeSaver)
3406B (PEEC) DIESEL TRUCK ENGINE Oil Cooler (BrakeSaver)
3406B (PEEC) DIESEL TRUCK ENGINE Pistons And Connecting Rod Assemblies
3406B (PEEC) DIESEL TRUCK ENGINE Cylinder Liners
3406B (PEEC) DIESEL TRUCK ENGINE Crankshaft Rear Seal And Wear Sleeve
3406B (PEEC) DIESEL TRUCK ENGINE Crankshaft Front Seal And Wear Sleeve
3406B (PEEC) DIESEL TRUCK ENGINE Crankshaft
3406B (PEEC) DIESEL TRUCK ENGINE Crankshaft Main Bearings
3406B (PEEC) DIESEL TRUCK ENGINE Connecting Rod Bearings
3406B (PEEC) DIESEL TRUCK ENGINE Jacobs Engine Brake
ELECTRONIC MODULAR CONTROL PANEL (EMCP) Systems Operation
ELECTRONIC MODULAR CONTROL PANEL (EMCP) Testing And Adjusting
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS Installation And Operation
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS Installation And Operation
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS Chapter 5. Troubleshooting
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS Appendix A. Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, & Modules
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS Appendix B. EMI Control in Electronic Governing Systems
TROUBLESHOOTING GUIDE [ETR] FOR SPARK IGNITED ENGINES EQUIPP Electric Protection System Functional Test
TROUBLESHOOTING GUIDE [ETR] FOR SPARK IGNITED ENGINES EQUIPP Electrical Schematics
TROUBLESHOOTING GUIDE [ETR] FOR SPARK IGNITED ENGINES EQUIPP Troubleshooting Full Protection System
TROUBLESHOOTING GUIDE [ETR] FOR SPARK IGNITED ENGINES EQUIPP Service Procedures
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.