SUPPLEMENT 3406B FUEL RATIO CONTROL Caterpillar


Fuel Ratio Control

Usage:

Remove and Install Fuel Ratio Control

1. Remove line (1) from the fuel ratio control. Remove two bolts (3), and remove solenoid (2) from the governor housing.

2. Disconnect throttle linkage (4) from the lever assembly on the side of the governor housing. (A test application is shown in the photo.)

3. Remove two bolts (5) from the front of the governor housing. Remove eight bolts (6), and remove governor housing (7).

4. Remove two bolts that hold fuel ratio control (8) to the governor housing. Unscrew the fuel ratio control from shaft (9) and remove it.

5. Remove plug and seal (10) from the governor housing.

6. Remove two bolts (12) that hold lock (11) and flange (14) on fuel ratio control (8). Remove lock (11), flange (14), and O-ring seal (13) from the fuel ratio control.

7. Check the condition of O-ring seal (13). If it is worn or damaged, make a replacement with a new part.

8. Remove ring (19) from the end of shaft (15). Remove lever assembly (18), spring (17), lever (16), spacer (21) and shaft (15) from the governor housing.

9. Remove pin (20) from lever assembly (18) with a hammer and punch. Remove shaft (9) from the lever assembly.

NOTE: The following steps are for the installation of the fuel ratio control.

10. Position shaft (9) in lever assembly (18) and install it with pin (20) using a hammer and punch.

11. Install shaft (15), spacer (21), lever (16), spring (17) and lever assembly (18) in the governor housing. Install ring (19) on the end of shaft (15).

12. Install O-ring seal (13) on fuel ratio control (8). Install flange (14) and lock (11) on the fuel ratio control with bolts (12).

13. Install seal and plug (10) in the governor housing.

14. Check the condition of the four O-ring seals on top of the governor housing where the fuel ratio control mounts. If any of the seals are worn or damaged, make a replacement with new parts.

15. Screw fuel ratio control (8) onto shaft (9) approximately six turns. Install the fuel ratio control with the two bolts that hold it to the governor housing.

16. Position governor housing (7), and install two bolts (5) on the front of the governor housing. Install eight bolts (6).

17. Connect throttle linkage (4) to the lever assembly on the side of the governor housing.

18. Install solenoid (2) with bolts (3). Install line (1) on the fuel ratio control.

19. Make an adjustment to the fuel ratio control. See the topic, FUEL RATIO CONTROL ADJUSTMENT in the TESTING AND ADJUSTING section of this Module.

Caterpillar Information System:

SUPPLEMENT 3406B FUEL RATIO CONTROL Testing and Adjusting
SUPPLEMENT 3406B FUEL RATIO CONTROL Systems Operation
VR3 VOLTAGE REGULATOR (10/12 LEAD), SELF-EXCITED SR4 GENERAT Attachments
VR3 VOLTAGE REGULATOR (10/12 LEAD), SELF-EXCITED SR4 GENERAT Testing And Adjusting
VR3 VOLTAGE REGULATOR (10/12 LEAD), SELF-EXCITED SR4 GENERAT Systems Operation
3500 Natural Gas Engines Protection System 3500 Natural Gas Engines Protection System
3500 Natural Gas Engine Protection System (For Serial Numbers 3RC1-152 and 4KC1-117) 3500 Natural Gas Engine Protection System (For Serial Numbers 3RC1-152 and 4KC1-117)
ELECTRIC PROTECTION SYSTEM Systems Operation
SUPPLEMENT FOR UPRATED 3500 ENGINES Vibration Damper Groups
SUPPLEMENT FOR UPRATED 3500 ENGINES Rear Gear Group (3512 & 3516)
SUPPLEMENT FOR UPRATED 3500 ENGINES Rear Gear Group (3508)
SUPPLEMENT FOR UPRATED 3500 ENGINES Crankshaft Wear Sleeves And Seals
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS 3406B (PEEC) Electronic Troubleshooting
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Programming PEEC Parameters
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Entering Passwords
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Troubleshooting Diagnostic Codes
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Troubleshooting Without A Diagnostic Code
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS PEEC Electronic System Functional Tests
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS PEEC System Calibrating And Adjusting
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Summary Of PEEC Personality Module Changes
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Parts List
3406B (PEEC) PROGRAMMABLE ELECTRONIC ENGINE CONTROLS Glossary Of PEEC Terms
3406B (PEEC) DIESEL TRUCK ENGINE Introduction
3406B (PEEC) DIESEL TRUCK ENGINE Engine Design
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.