D379, D398, D399 INDUSTRIAL & MARINE ENGINES Caterpillar


Sea Water Pump

Usage:

Remove Sea Water Pump

1. Remove plug from bottom of pump and remove sea water from pump.

2. Disconnect inlet line from cover (3).

3. Remove elbow (1) and top tank (2) from the pump.

4. Remove the retainer assembly (4).

5. Remove cover (3) and gaskets from the pump.

6. Remove the six bolts that hold pump to accessory drive housing.

7. Remove the sea water pump.

Install Sea Water Pump

1. Put the sea water pump (1) on the engine. Install the bolts that hold pump to accessory drive housing.

2. Install the retainer assembly (4).

3. Install the cover (2) with enough gaskets (5) to have a clearance of .005 to .020 in. (0.13 to 0.51 mm) between cover (2) and face of impeller (3).

4. Install the top tank and elbow.

5. Connect the inlet line to cover (2). Install the plug in bottom of pump.

Disassemble Sea Water Pump

start by:

a) remove sea water pump

1. Remove the cotter pin, nut and washer that hold impeller to shaft.

2. Install the nut even with end of shaft. Install two 5/16"-18 NC x 2 in. long bolts in the impeller. Loosen the impeller from taper of shaft with tooling (A).

3. Remove tooling (A). Remove nut, impeller, plate and gasket (1).

4. Remove the cotter pins (4) and ring (2) from pins.

5. Remove the plate (3) and bellows (5) from the housing.

6. Remove six bolts and locks.

7. Remove the gear (6) from shaft.

8. Remove four bolts (9) and locks that hold bearing on retainer. Remove bearing (10).

9. Remove two bolts (8) and locks that hold retainer to housing. Remove retainer assembly (7).

10. Remove the bearing (11) from retainer.

11. Remove the seal (12) from retainer.

Assemble Sea Water Pump

1. Install bearing in retainer with tooling (A). Install bearing with oil hole in bearing in alignment with oil hole in retainer.

2. Install seal in retainer with tooling (B). Install seal with lip toward the bearing.

3. Put clean engine oil on lip of seal.

4. Install retainer assembly (3). Install the bearing (4). Install the shaft (2).

5. Install the gear (1) on shaft.

6. Install the bellows and plate in housing. The smooth side of plate must be away from housing.

7. Install the ring (5) and cotter pins.

8. Install the gasket and plate. The smooth side of plate must be away from impeller.

9. Install the impeller (6).

10. Install the washer and nut (7). Tighten the nut to 55 ± 10 lb.ft. (75 ± 14 N·m) and install cotter pin. If cotter pin cannot be installed, tighten nut until it can be installed.

end by:

a) install sea water pump

Caterpillar Information System:

D379, D398, D399 INDUSTRIAL & MARINE ENGINES Oil Filter Housing
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Fuel Filter Housing
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Expansion Tank (Marine Engines)
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Water Temperature Regulators
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Fuel Priming Pump
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Fuel Transfer Pump
D379, D398, D399 INDUSTRIAL & MARINE ENGINES General Instructions
D379, D398, D399 INDUSTRIAL & MARINE ENGINES D379, D398I on Engine Attachments Testing And Adjusting
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Systems Operations D379, D398, D399 I & M Engine Attachments
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Contactor Switch For Oil Pressure
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Contactor Switch For Temperature
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Contactor Switch For Overspeed
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Vibration Damper (D398 and D399)
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Crankshaft Front Seal Ring And Thrower
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Crankshaft Front Seal (Lip Type) And Wear Sleeve
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Service Meter And Tachometer Drive
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Accessory Drive Housing
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Accessory Drive Gears
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Oil Pressure Relief Valve
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Oil Pump
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Engine Oil Cooler
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Fresh Water Pump
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Prelubrication Oil Pump (D399)
D379, D398, D399 INDUSTRIAL & MARINE ENGINES Connecting Rod Bearings
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.