Fuel System

The sleeve metering fuel system is a pressure type fuel system. The name for the fuel system is from the method used to control the amount of fuel sent to the cylinders. This fuel system has an injection pump for each cylinder of the engine. It also has a fuel transfer pump on the front of the injection pump housing. The governor is on the rear of the injection pump housing.

The drive gear for the fuel transfer pump is on the front of the camshaft for the injection pumps. The carrier for the governor weights is bolted to the rear of the camshaft for the injection pumps. The injection pump housing has a bearing at each end to support the camshaft. The camshaft for the sleeve metering fuel system is driven by the timing gears at the front of the engine.

The injection pumps, lifters and rollers, and the camshaft are all inside of the pump housing. The pump housing and the governor housing are full of fuel at transfer pump pressure (fuel system pressure).

This fuel system has governor weights, a thrust collar and two governor springs. One governor spring is for high idle and the other governor spring is for low idle. Rotation of the shaft for governor control, compression of the governor springs, movement of connecting linkage in the governor and injection pump housing controls the amount of fuel sent to the engine cylinders.

Fuel from fuel tank (7) is pulled by fuel transfer pump (11) through water separator (F) (if so equipped) and fuel filter (9). From fuel filter (9) the fuel goes to housing for fuel injection pumps (14). The fuel goes in housing (14) at the top and goes through inside passage (20) to fuel transfer pump (11).

SCHEMATIC OF FUEL SYSTEM
1. Fuel priming pump (closed position). 2. Fuel priming pump (open position). 3. Return line for constant bleed valve. 4. Constant bleed valve. 5. Manual bleed valve. 6. Fuel injection nozzle. 7. Fuel tank. 8. Fuel inlet line. 9. Fuel filter. 10. Bypass valve for fuel priming pump. 11. Fuel transfer pump. 12. Fuel bypass valve. 13. Camshaft. 14. Housing for fuel injection pumps. A. Check valve. B. Check valve. C. Check valve. D. Check valve. F. Water Separator.

CROSS SECTION OF FUEL SYSTEM WITH DASHPOT GOVERNOR
11. Fuel transfer pump. 13. Camshaft. 14. Housing for fuel injection pumps. 15. Lever. 16. Governor housing. 17. Load stop pin. 18. Cover. 19. Sleeve control shafts (two). 20. Inside fuel passage. 21. Drive gear for fuel transfer pump. 22. Lever on governor shaft. 23. Piston for dashpot governor. 24. Spring for dashpot governor. 25. Governor springs (inner spring is for low idle: outer spring is for high idle). 26. Spring seat. 27. Over fueling spring. 28. Thrust collar. 29. Load stop lever. 30. Carrier and governor weights. 31. Sleeve levers. E. Orifice for dashpot.

From fuel transfer pump (11), fuel under pressure, fills the housing for the fuel injection pumps (14). Pressure of the fuel in housing (14) is controlled by bypass valve (12). Pressure of the fuel at FULL LOAD is 30 ± 5 psi (205 ± 35 kPa). If the pressure of fuel in housing (14) gets too high, bypass valve (12) will move (open) to let some of the fuel return to the inlet of fuel transfer pump (11).

Lever (15) for the governor is connected by linkage and governor springs (25) to the sleeve control shafts (19). Any movement of lever (22) will cause a change in the position of sleeve control shafts (19).

When lever (15) is moved to give more fuel to the engine, lever (22) will put governor springs (25) in compression and move thrust collar (28) forward. As thrust collar (28) moves forward, the connecting linkage will cause sleeve control shafts (19) to turn. With this movement of the sleeve control shafts, levers (31) will lift sleeves (32) to make an increase in the amount of fuel sent to the engine cylinders.

When starting the engine, the force of over fueling spring (27) is enough to push thrust collar (28) to the full fuel position. This lets the engine have the maximum amount of fuel for injection when starting. At approximately 400 rpm, governor weights (30) make enough force to push spring (27) together. Thrust collar (28) and spring seat (26) come into contact. From this time on, the governor works to control the speed of the engine.

GOVERNOR PARTS
23. Piston for dashpot governor. 24. Spring for dashpot governor. 26. Spring seat. 27. Over fueling spring. 28. Thrust collar.

When governor springs (25) are put in compression, the spring seat at the front of the governor springs will make contact with load stop lever (29). Rotation of the load stop lever moves load stop pin (17) up until the load stop pin comes in contact with the stop bar or stop screw. This stops the movement of thrust collar (28), the connecting levers, and sleeve control shafts (19). At this position, the maximum amount of fuel per stroke is being injected by each injection pump.

The carrier for governor weights (30) is held on the rear of camshaft (13) by bolts. When engine rpm goes up, injection pump camshaft (13) turns faster. Any change of camshaft rpm will change the rpm and position of governor weights (30). Any change of governor weight position will cause thrust collar (28) to move. As governor weights (30) turn faster, thrust collar (28) is pushed toward governor springs (25). When the force of governor springs (25) is balanced by the centrifugal force of the governor weights, sleeves (32) of the injection pumps are held at a specific position to send a specific amount of fuel to the engine cylinders.

The parts of the dashpot work together to make the rpm of the engine steady. The dashpot works as piston (23) moves in the cylinder which is filled with fuel. The movement of piston (23) in the cylinder either pulls fuel into the cylinder or pushes it out. In either direction the flow of fuel is through orifice (E). The restriction to the flow of fuel by orifice (E) gives the governor its function.

When the load on the engine decreases, the engine starts to run faster and governor weights (30) put force against springs (25). This added force puts more compression on springs (25) and starts to put spring (24) in compression. Spring (24) is in compression because the fuel in the cylinder behind piston (23) can only go out through orifice (E). The rate of flow through orifice (E) controls how fast piston (23) moves. As the fuel is pushed out of the cylinder by piston (23), the compression of spring (24) becomes gradually less. When springs (25) and spring (24) are both in compression, their forces work together against the force of weights (30). This gives the effect of having a governor spring with a high spring rate. A governor spring with a high spring rate keeps the engine speed from having oscillations during load changes.

When the load on the engine increases, the engine starts to run slower. Governor weights (30) puts less force against spring (25). Spring (25) starts to push seat (26) to give engine more fuel. Seat (26) is connected to piston (23) by spring (24). When seat (26) starts to move, the action puts spring (24) in tension. As piston (23) starts to move, a vacuum is made inside the cylinder. The vacuum will pull fuel into the cylinder through orifice (E). The rate of fuel flow through orifice (E) again controls how fast piston (23) moves. During this condition, spring (24) is pulling against springs (25). This makes the movement of seat (26) and springs (25) more gradual. This again gives the effect of a governor spring with a high spring rate.

FUEL SYSTEM COMPONENTS
14. Housing for fuel injection pumps. 19. Sleeve control shafts. 31. Sleeve levers. 32. Sleeves.

When the governor control lever is turned toward the FUEL-OFF position with the engine running, there is a reduction of force on governor springs (25). The movement of the linkage in the governor will cause fuel control shafts (19) to move sleeves (32) down, and less fuel will be injected in the engine cylinders.

To stop the engine, turn the ignition switch to the "OFF" position. This will cause the shut-off solenoid to move linkage in the fuel pump housing. Movement of the linkage will cause sleeve levers (31) to move sleeves (32) down, and no fuel is sent to the engine cylinders. With no fuel going to the engine cylinders, the engine will stop.

Flow Of Fuel Using The Priming Pump

When the handle of priming pump (2) is pulled out, negative air pressure in priming pump (2) opens check valve (A) and pulls fuel from fuel tank (7). Pushing the handle in closes check valve (A) and opens check valve (B). This pushes air and/or fuel into housing (14) through the fuel passages and check valve (C). More operation of priming pump (2) will pull fuel from fuel tank (7) until the fuel lines, fuel filter (9) and housing (14) are full of fuel. Do this until the flow of fuel from manual bleed valve (5) is free of air bubbles. Relief valve (10) will open and let the fuel go to the inlet for fuel priming pump (2) if the pressure gets higher than 20 psi (140 kPa) when using priming pump (2).

Constant Bleed Valve

Constant bleed valve (4) lets approximately 9 gallons of fuel per hour go back to fuel tank (7). This fuel goes back to fuel tank (7) through return line for constant bleed valve (3). This flow of fuel removes air from housing (14) and also helps to cool the fuel injection pump. Check valve (D) makes a restriction in this flow of fuel until the pressure in housing (14) is at 8 ± 3 psi (55 ± 20 kPa).

CONSTANT BLEED VALVE
4. Constant bleed valve. D. Check valve.

Operation Of Fuel Injection Pumps

The main components of a fuel injection pump in the sleeve metering fuel system are barrel (A), plunger (B), and sleeve (D). Plunger (B) moves up and down inside the barrel (A) and sleeve (D). Barrel (A) is stationary while sleeve (D) is moved up and down on plunger (B) to make a change in the amount of fuel for injection.

FUEL INJECTION SEQUENCE
1, 2, 3. Injection stroke (positions) of a fuel injection pump. 4. Injection pump camshaft. A. Barrel. B. Plunger. C. Fuel inlet. D. Sleeve. E. Fuel outlet. F. Lifter.

When the engine is running, fuel under pressure from the fuel transfer pump goes in the center of plunger (B) through fuel inlet (C) during the down stroke of plunger (B). Fuel can not go through fuel outlet (E) at this time because it is stopped by sleeve (D), (see position 1).

Fuel injection starts (see position 2) when plunger (B) is lifted up in barrel (A) enough to close fuel inlet (C). There is an increase in fuel pressure above plunger (B), when the plunger is lifted by camshaft (4). The fuel above plunger (B) is injected in to the engine cylinder.

Injection will stop (see position 3) when fuel outlet (E) is lifted above the top edge of sleeve (D) by camshaft (4). This movement lets the fuel that is above, and in, plunger (B) go through fuel outlet (E) and return to the fuel injection pump housing.

When the sleeve (D) is raised on plunger (B), fuel outlet (E) is covered for a longer time, causing more fuel to be injected in the engine cylinders. If sleeve (D) is low on plunger (B), fuel outlet (E) is covered for a shorter time, causing less fuel to be injected.

Operation Of 9L6969 Fuel Injection Nozzle

The fuel inlet (6) and nozzle tip (13) are parts of the nozzle body (11). Valve (8) is held in position by spring force. Force of the spring is controlled by pressure adjustment screw (3). Locknut (4) holds pressure adjustment screw (3) in position. The lift of valve (8) is controlled by lift adjustment screw (2). Locknut (10) holds lift adjustment screw (2) in position. Compression seal (7) goes on nozzle body (11).

The compression seal goes against inlet fitting (6) and prevents the leakage of compression from the cylinder. Carbon dam (12), at the lower end of nozzle body (11), prevents the deposit of carbon in the bore in the cylinder head.

FUEL INJECTION NOZZLE
1. Cap. 2. Lift adjustment screw. 3. Pressure adjustment screw. 4. Locknut for pressure adjustment screw. 5. O-ring seal. 6. Fuel inlet. 7. Compression seal. 8. Valve. 9. Orifices (four). 10. Locknut for lift adjustment screw. 11. Nozzle body. 12. Carbon dam. 13. Nozzle tip.

Fuel, under high pressure from the fuel injection pump goes through the hole in fuel inlet (6). The fuel then goes around valve (8), fills the inside of nozzle body (11) and pushes against the valve guide. When the force made by the pressure of the fuel is more than the force of the spring, valve (8) will lift. When valve (8) lifts, fuel under high pressure will go through the four .0128 in. (0.325 mm) orifices (9) into the cylinder. When the fuel is sent to the cylinder, the force made by the pressure of the fuel in the nozzle body will become less. The force of the spring will then be more than the force of the pressure of the fuel in the nozzle body. Valve (8) will move to the closed position.

Valve (8) is a close fit with the inside of nozzle tip (13), this makes a positive seal for the valve.

When the fuel is sent to the cylinder, a very small quantity of fuel will leak by the valve guide. This fuel gives lubrication to the moving parts of the fuel injection nozzle.

Automatic Timing Advance Unit

The automatic timing advance unit (2) is installed on the front of the camshaft (3) for the engine. The automatic timing advance unit (2) drives the gear (1) on the camshaft for the fuel injection pump. This gear is the drive for the camshaft for the fuel injection pump.

AUTOMATIC TIMING ADVANCE UNIT
1. Gear on camshaft for fuel injection pump. 2. Automatic timing advance unit. 3. Camshaft for the engine.

The weights (4) in the timing advance are driven by two slides (6) that fit into notches made on an angle in the weights. The slides (6) are driven by two dowels which are in the drive gear for the engine camshaft. As centrifugal force (rotation) moves weights (4) outward against the force of springs (5), the movement of the notches in weights (4) will cause the slides to make a change in the angle between the timing advance gear and the two drive dowels in the drive gear for the engine camshaft. Since the timing advance unit drives the gear (1) on the camshaft for the fuel injection pump, the fuel injection timing is also changed.

The automatic timing advance unit will change the timing 5 degrees. This change starts at approximately low idle rpm and is operating up through the rated speed of the engine. No adjustment can be made to the automatic timing advance unit.

Lubrication oil for the timing advance unit comes from drilled holes that connect with the front bearing for the engine camshaft.

AUTOMATIC TIMING ADVANCE UNIT
4. Weights. 5. Springs. 6. Slides.

Function Of Fuel Junction Block

The location of the fuel junction block (4) is at the right rear of the engine. The fuel lines from the fuel tank and the engine connect at fuel junction block (4).

CONNECTIONS FOR FUEL LINES AT THE FUEL JUNCTION BLOCK
1. Connection for constant bleed line to housing for fuel injection pumps. 2. Connection for constant bleed line to fuel tank. 3. Connection for fuel supply line to fuel filter. 4. Fuel junction block. 5. Connection for fuel supply line to fuel tank.

Water Separator

Some engines have a water separator. The water separator is installed between the fuel tank and the rest of the fuel system. For efficiency in the action of the water separator the fuel flow must come directly from the fuel tank and through the water separator. This is because the action of going through a pump or valves before the water separator lowers the efficiency of the water separator.

The water separator can remove 95% of the water in a fuel flow of up to 33 gph (125 litre/hr) if the concentration of the water in the fuel is 10% or less. It is important to check the water level in the water separator frequently. The maximum amount of water which the water separator can hold is 0.8 pt. (0.4 litre). At this point the water fills the glass to 3/4 full. Do not let the water separator have this much water before draining the water. After the water level is at 3/4 full, the water separator loses its efficiency and the water in the fuel can go through the separator and cause damage to the fuel injection pump.

Drain the water from the water separator every day or when the water level gets to 1/2 full. This gives the system protection from water in the fuel. If the fuel has a high concentration of water, or if the flow rate of fuel through the water separator is high, the water separator fills with water faster and must be drained more often.

To drain the water separator, open drain valve (2) in the drain line and vent valve (1) at the top of the water separator. Let the water drain until it is all out of the water separator. Close both valves.

WATER SEPARATOR
1. Vent valve. 2. Drain valve.

Air Inlet And Exhaust System

AIR INLET AND EXHAUST SYSTEM
1. Air inlet pipe. 2. Pipe plug. 3. Mounting flange for the air cleaner. 4. Fitting. 5. Positive crankcase ventilator valve. 6. Inlet manifolds. 7. Valve cover. 8. Exhaust manifolds.

The air inlet system is on the top side of the engine. The air cleaner goes on air inlet pipe (1). The air inlet pipe sends air to both cylinder heads. The air inlet pipe can not be turned end for end because the mounting flange for the air cleaner (3) has a small angle toward the front of the engine.

The air inlet manifolds (6) are made as a part of the cylinder heads. The air inlet openings and the design of the combustion chamber give the air needed for complete combustion.

The exhaust system is on each side of the engine. The exhaust manifolds (8) are along the outside of the cylinder heads. The exhaust manifold for the right side of the engine will not go on the left side of the engine. The exhaust manifold for the left side of the engine will not go on the right side of the engine.

A positive crankcase ventilator valve (5) goes on valve cover (7). Valve (5) will return crankcase fumes to the engine through air inlet pipe (1).

Valve cover (7) can also be put on the other cylinder head. When valve cover (7) is put on the other cylinder head, fitting (4) must be exchanged with pipe plug (2) in the air inlet pipe (1).

CYLINDER HEAD AND VALVES
1. Push rod. 2. Cam follower. 3. Guide support. 4. Rocker arm shaft. 5. Rocker arm. 6. Exhaust valve. 7. Valve seat insert. 8. Intake valve. 9. Valve spring.

The valves and valve system components control the flow of inlet air and exhaust gases into and out of the cylinder during engine operation.

The intake and exhaust valves are opened and closed by movement of these components; crankshaft, camshaft, cam followers, push rods, rocker arms, and valve springs. Rotation of the crankshaft causes rotation of the camshaft. The camshaft gear is driven by, and timed to, a gear on the front of the crankshaft. When the camshaft turns, the cams on the camshaft also turn and cause the cam followers to go up and down. This movement makes the push rods move the rocker arms. The movement of the rocker arms will make the intake and exhaust valves in the cylinder head open and close according to the firing order (injection sequence) of the engine. One valve spring for each valve helps to hold the valves in the closed position.

There is one intake and one exhaust valve for each cylinder. The valve seat insert for the exhaust valve can have replacement. The valve seat for the intake valve is machined in and is a part of the cylinder head. When the seat for the intake valve has been machined to the limits given in the SPECIFICATIONS, it can be bored (machined) for a valve seat insert. The valve guide bore is machined in and is a part of the cylinder head.

Lubrication System

SCHEMATIC OF LUBRICATION SYSTEM
1. Vacuum pump or air compressor. 2. Cylinder head. 3. Front cover for the engine. 4. Oil manifold. 5. Base for the oil cooler. 6. Bypass valve. 7. Oil cooler. 8. Oil pump. 9. Cover for oil pump. 10. Suction bell for oil pump. 11. Bypass valve. 12. Bypass valve. 13. Oil filters.

The lubrication system uses a six lobe, rotor type oil pump (8). Bolts hold the cover for the oil pump (9) on the front cover for the engine (3). The gear on the crankshaft drives the outer rotor. The outer rotor has rotation in a bearing in the front cover for the engine. The inner rotor goes on a short shaft in the front cover for the engine. The inner rotor is driven by the outer rotor.

A bypass valve (6), in the cover for the oil pump (9), controls the pressure of the oil coming from oil pump (8). The pump can put more oil into the system than needed. When the pressure of the oil going into the engine is more than 75 to 85 psi (520 to 590 kPa), the bypass valve (6) will open. This permits the oil that is not needed to go to the inlet oil passage of the oil pump.

Oil from the oil pan is pulled through the suction bell for the oil pump (10) by oil pump (8). The oil is sent by the pump to an oil passage in the front cover for the engine (3). Oil from this passage goes to the cylinder block and on to base for the oil cooler (5). The base for the oil cooler is on the left side of the engine, near the front of the engine. Bypass valve (11), in the base for the oil cooler, will let the oil go around the oil cooler (7) when the oil is cold or if the restriction in the oil cooler is more than the other parts of the system. A difference in pressure of 12 to 15 psi (85 to 105 kPa) between the oil inlet and the oil outlet will open the bypass valve.

There are two pressure outlets in the base for the oil cooler. The pressure outlets are on the outlet side of the oil cooler and oil filters. The pressure outlets are for the sending unit and switch for the oil pressure.

Oil from the oil filters (13) goes through a passage in the cylinder block to oil manifold (4). The oil manifold is in the center of the cylinder block, above the camshaft, and goes the full length of the cylinder block. Oil goes from the oil manifold to the bearings for the camshaft. There are grooves in the bore in the cylinder block around the bearings for the camshaft. The bearing surfaces (journals) on the camshaft get lubrication from these grooves through a hole in the bearings for the camshaft. Some of the oil goes around the grooves and down through a passage to a hole and groove in the top half of the main bearing. Oil from the hole and groove gives lubrication to the bearing surfaces (journals) of the crankshaft for the main bearings.

Oil gets into the crankshaft through holes in the bearing surfaces (journals) for the main bearings. Passages connect the bearing surface (journal) for the main bearing with the bearing surface (journal) for the connecting rod. The piston pin gets lubrication from oil thrown by other parts.

Oil for the rocker arms comes from the oil manifold (4) through passages in the cylinder block. The passages in the cylinder block are in alignment with a passage in each cylinder head. The passage to the cylinder head on the left side is near the front of the cylinder block. The passage to the cylinder head on the right side is near the rear of the cylinder block.

The passage in each cylinder head sends the oil into an oil hole in the bottom of the mounting surface of the bracket that holds the shaft for the rocker arms. The oil hole is in the front bracket on the left side and in the rear bracket on the right side. The oil then goes up through the bracket and into the center of the shaft for the rocker arms. Oil goes along the center of the shaft to the bearings for the rocker arms. From the rocker arms, the oil is pushed through small holes to give lubrication to the valves, push rods, cam followers, and camshaft lobes.

After the lubrication oil has done its work, it will return to the oil pan for the engine.

SCHEMATIC OF OIL PASSAGES IN CRANKSHAFT

Cooling System

COOLING SYSTEM WITH STANDARD VERTICAL RADIATOR
1. Radiator cap. 2. Radiator top tank. 3. Radiator top hose. 4. Shunt line. 5. Housing for water temperature regulators. 6. Coolant to housing for water temperature regulators. 7. Cylinder heads (two). 8. Vent tube. 9. Surge tank. 10. Inside bypass. 11. Radiator bottom tank. 12. Radiator bottom hose. 13. Water pump. 14. Outlet line for oil cooler. 15. Oil cooler. 16. Inlet line for oil cooler. 17. Cylinder block. A. Orifices between cylinder heads and front cover. B. Orifice in oil cooler inlet.

COOLING SYSTEM WITH CROSS FLOW RADIATOR
1. Radiator cap. 2. Radiator left side tank. 3. Radiator top hose. 4. Shunt line. 5. Housing for water temperature regulators. 6. Coolant to housing for water temperature regulators. 7. Cylinder heads (two). 8. Vent tube. 9. Surge tank. 10. Inside bypass. 11. Radiator right side tank. 12. Radiator bottom hose. 13. Water pump. 14. Outlet line for oil cooler. 15. Oil cooler. 16. Inlet line for oil cooler. 17. Cylinder block. A. Orifices between cylinder heads and front cover for the engine. B. Orifice in oil cooler inlet.

COOLING SYSTEM WITH VERTICAL RADIATOR AND SEPARATE SURGE TANK
1. Radiator cap. 2. Radiator top tank. 3. Radiator top hose. 4. Shunt line. 5. Housing for water temperature regulators. 6. Coolant to housing for water temperature regulators. 7. Cylinder heads (two). 8. Vent tube. 9. Surge tank. 10. Inside bypass. 11. Radiator bottom tank. 12. Radiator bottom hose. 13. Water pump. 14. Outlet line for oil cooler. 15. Oil cooler. 16. Inlet line for oil cooler. 17. Cylinder block. A. Orifices between cylinder heads and front cover. B. Orifice in oil cooler inlet.

Water pump (13) is installed on the front face of the front cover for the engine and is driven by V belts from the crankshaft pulley. The inlet opening of water pump (13) is connected to radiator bottom hose (12). The outlet flow of coolant from water pump (13) goes through inside passages in the front cover for the engine.

As the coolant goes from the water pump, it divides and goes through the inside passages in the front cover for the engine to cylinder block (17). Most of the coolant goes through cylinder block (17) and up to cylinder heads (7). From cylinder heads (7) the coolant goes forward through orifices (A) to the front cover for the engine.

Part of the coolant going to the left side (as seen from the flywheel) of cylinder block (17) goes through orifice (B) to inlet line (16) and on to oil cooler (15), to cool the oil for lubrication of the engine, and back to the front cover for the engine through outlet line (14).

From the front cover for the engine, the coolant either goes to the inlet for water pump (13) or to the radiator.

If the coolant is cold (cool), the water temperature regulators (18) will be closed. The coolant will go through inside bypass (10) to water pump (13). If the coolant is warm, the water temperature regulators (18) will be open. When the water temperature regulators (18) are open, they make a restriction in the inside bypass (10) and the coolant goes through radiator top hose (3) and into radiator top tank (2) or left side tank (2). Coolant then goes through the core of the radiator to the radiator bottom tank (11) or radiator right side tank (11), where it is again sent through the cooling system. A small part of the coolant goes through inside bypass (10) when temperature regulators (18) are open.

FLOW OF COOLANT
3. Radiator top hose. 5. Housing (water temperature regulators). 6. Coolant to housing for water temperature regulators. 10. Inside bypass. 18. Water temperature regulators (two). C. Flow with warm coolant. D. Flow with cold coolant.

LOCATION OF WATER TEMPERATURE REGULATORS

The vertical radiator is made with a top tank (2) above the core and a surge tank (9) either above or separate from the top tank. Vent tube (8) connects radiator top tank (2) and surge tank (9). The cross flow radiator is made with a left side tank (2) and a right side tank (11). The surge tank (9) is a part of right side tank (11), separated by an inside baffle. Vent tube (8) connects the surge tank (9) to the radiator.

Surge tank (9) has a shunt line (4) that connects to the inlet of water pump (13). This shunt type system keeps a positive pressure on the inlet of water pump (13) at all times. When putting coolant in the cooling system, coolant from surge tank (9) goes through shunt line (4) to the inlet of water pump (13) and fills cylinder block (17) from the bottom. By filling the system from the bottom, any air in the system is pushed out through radiator top tank (2), through vent tube (8) into surge tank (9).

Radiator cap (1) is used to keep the correct pressure in the cooling system. This pressure keeps a constant supply of coolant to water pump (13). If this pressure goes too high, a valve in radiator cap (1) moves (opens) to get a reduction of pressure. When the correct pressure is in the cooling system, the valve in radiator cap (1) moves down (to the closed position).

LOCATION OF VENT HOLE

The vent hole is located in the front housing and the outlet elbow is used to let the air out of the cylinder block and head when filling the cooling system with coolant.

It is important to keep the vent hole clean and open. If the vent hole is not open it will keep the engine from completely filling with coolant.

LOCATIONS OF HEATER CONNECTIONS

The front housing has several plugs that give access to water passages inside the housing. For the correct access points to install heater hoses, see the LOCATIONS OF HEATER CONNECTIONS picture.

Basic Block

Vibration Damper

The twisting of the crankshaft, due to the regular power impacts along its length, is called twisting (torsional) vibration. The vibration damper is installed on the front end of the crankshaft. It is used for reduction of torsional vibrations and stops the vibration from building up to amounts that cause damage.

The damper is made of a flywheel ring (1) connected to an inner hub (3) by a rubber ring (2). The rubber makes a flexible coupling between the flywheel ring and the inner hub.

CROSS SECTION OF A VIBRATION DAMPER
1. Flywheel ring. 2. Rubber ring. 3. Inner hub.

Electrical System

The electrical system has three separate circuits: the charging circuit, the starting circuit and the low amperage circuit. Some of the electrical system components are used in more than one circuit. The battery (batteries), circuit breaker, ammeter, cables and wires from the battery are all common in each of the circuits.

The charging circuit is in operation when the engine is running. An alternator makes electricity for the charging circuit. A voltage regulator in the circuit controls the electrical output to keep the battery at full charge.

The starting circuit is in operation only when the start switch is activated.

The low amperage circuit and the charging circuit are both connected to the same side of the ammeter. The starting circuit connects to the opposite side of the ammeter.

System Components

Alternator (Delco-Remy)

The alternator is a three phase, self rectifying charging unit. The regulator for the alternator is part of the alternator. The alternator is driven from the crankshaft pulley by two V type belts.

The only part in the alternator which has movement is the rotor. The rotor is held in position by a ball bearing at the drive end and a roller bearing at the rectifier end.

ALTERNATOR (DELCO-REMY)

The compartment for the regulator is sealed. The regulator controls the alternator output according to the needs of the battery and the other components in the electrical system.

Starting Motor

The starting motor is used to turn the engine flywheel fast enough to get the engine running.

STARTING MOTOR
1. Field. 2. Solenoid. 3. Clutch. 4. Pinion. 5. Commutator. 6. Brush assembly. 7. Armature.

The starting motor has a solenoid. When the start switch is activated, electricity from the electrical system will cause the solenoid to move the starter pinion to engage with the ring gear on the flywheel of the engine. The starter pinion will engage with the ring gear before the electric contacts in the solenoid close the circuit between the battery and the starting motor. When the start switch is released, the starter pinion will move away from the ring gear of the flywheel.

Solenoid

SCHEMATIC OF A SOLENOID
1. Coil. 2. Switch terminal. 3. Battery terminal. 4. Contacts. 5. Spring. 6. Core. 7. Component terminal.

A solenoid is a magnetic switch that uses low current to close a high current circuit. The solenoid has an electromagnet with a core (6) which moves.

There are contacts (4) on the end of core (6). The contacts are held in the open position by spring (5) that pushes core (6) from the magnetic center of coil (1). Low current will energize coil (1) and make a magnetic field. The magnetic field pulls core (6) to the center of coil (1) and the contacts close.