1979/03/07 Caterpillar


Retroreflective Tape Makes Phototach Kit Easier To Read

Usage:




A 6V93 Sheeting Tape is available to use with any phototach, including the 1P5500 Phototach Kit. Use of this tape makes it easier to read the phototach.

This is a special tape with a retroreflective surface. This surface causes the light to come straight back (reflect) from the surface to the source of the light, which is the phototach. See Illustration 1. This gives more exact indications of revolutions per minutes (rpm) than if paint or white tape is used. The source of light can be as far away as 3 ft (1 m) from the new tape, and at any angle. It is best to hold the pickup head of the phototach at an angle to the surface. When held at an angle, shiny spots can not make the light come back to the phototach and cause wrong readings.

The new tape can be used on shafts, gears, fan blades, etc. You must always put the tape in a location so the light from the photohead hits the tape. One piece of tape is enough, but the more pieces of tape used, the more exact the rpm indications will be.

The tape adheres (holds) strongly to any surface if it is almost clean. A cover, or liner, is used on the tape so it will not stick (fasten) together when in a roll. For this reason, the tape must be used and put in storage carefully so the roll will always be together. One recommendation is to put 4 pieces of any kind of tape on both sides of the roll. See Illustration 2. Keep the roll of tape in the bag the tape came in to protect the tape.

The tape is .5" (13 mm) wide and 50 yards (45.7 m) are in each roll.


Illustration 1. This drawing shows the difference between how the rays of light change direction on the new tape surface in comparison with normal surfaces.


Illustration 2. Use pieces of tape to keep the roll together when in storage.

Caterpillar Information System:

1979/03/07 Window Cover Kit Now Available For ENM Service Meters
1979/03/07 Use SIRS To Keep Service Literature Current
1979/03/07 Check Valve Must Be Adjusted Correctly To Let Fuel Flow Through The Return Line And Back To The Tank
1979/03/07 New Fuel Injection Lines Groups Use A Different Fuel Injection Nozzle Assembly
1979/03/07 Engine Valve Springs Are Now Made Of Carbon Steel Alloy
1979/03/07 New Manifold Assembly Gives More Room For The Lifting Eye
1979/03/07 New Exhaust Valve And Valve Guide
1979/03/07 Engine Mounted Exhaust Brake Systems Can Be Used To Extend Service Brake Life
1979/03/07 High Sulfur Fuel Can Cause Severe Engine Wear And Internal Damage
1979/03/07 New Larger Capacity Water Separator Is Available
1979/03/07 Stronger Suction Bell Assembly Now Used In Engine Oil Lines Group
1979/03/07 Federal Law Prohibits Tampering With Noise Control Systems
1979/03/07 New Exhaust Pipe Connector Makes A Tighter Seal Between Pipe And Manifold
1979/03/14 New Oil Filter And Filter Base Assemblies
1979/03/14 New Piston And Connecting Rod Are Tapered In Area Of Piston Pin
1979/03/14 New Fuel Injection Nozzles Are Used In 3208 Engines
1979/03/14 New Engine Cylinder Block Used
1979/03/14 Improvements Made To Fuel Injection Pump And Governor Group
1979/03/14 8L4525 Flange Is Available Again For Parts Service Of 3192 Marine Transmissions
1979/03/14 Main Bearings Now Have Larger Diameter Oil Hole For Better Lubrication Of Main And Rod Bearings
1979/03/14 Maintenance Procedures For Extended FPTO Life On 3408 And 3412 Marine Engines
1979/03/14 Larger Diameter Washer Is Used To Hold Air Transfer Pipe In Aftercooler Flange
1979/03/14 List Of Service Publications
1979/03/14 Revision To Guideline For Reusable Parts Is Available
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.