1979/01/24 Caterpillar


5P9705 Tapered Rod Tool Group Used For Removal And Installation Of Piston Pin Bearings In Tapered Connecting Rods

Usage:




3208 Engines (Equipped With Tapered Rod Bushings)

SUPPLEMENT: 03/14/79

ENGINE NEWS, JANUARY 24, 1979, PAGE 6.

In the article "5P9705 Tapered Rod Tool Group Used For Removal And Installation Of Piston Pin Bearings In Tapered Connecting Rods", two of the part numbers and names shown in the illustration are wrong. Put marks through the part numbers and names. The correct information is shown in the illustration which follows. Make a correction to the JANUARY 24, 1979 ENGINE NEWS.

--------------- END SUPPLEMENT ---------------

A 5P9705 Tapered Rod Tool Group (see the Illustration) is available for service work on 3208 Engines that have taper-type bearings in the pin bore.

A new piston group is used in 3208 Engines. The design of the new piston group increases pin bore fatigue strength. The piston has tapered inner bosses and the rod has a tapered end which uses a taper-type bearing.

The 5P9705 Tapered Rod Tool Group must be used with the 5P8639 Press Group for removal or installation of these bearings.

Each part of the 5P9705 Tapered Rod Tool Group is available separately. Dealers who have the 6V100 Tool Arrangement need only add the 5P9704 Spacer from the tool group.


5P9705 Tapered Rod Tool Group.

Caterpillar Information System:

1979/01/24 New Tachometer Drive Adapter Has Increased Service Life
1979/01/24 Current Chart For Dynamometer Adapters
1979/01/24 Ether Starting Aid Groups Are Now Available
1979/01/24 A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/10 Improved Woodward Governor Groups
1979/01/10 Stronger Fan Adjustment Bracket Used In Fan Drive Group
1979/01/10 Caution: Do Not Change Orifice In Water Outlet Of Auxiliary Pump Group
1979/01/10 New 6V87 Gauge Measures Valve Stem Wear
1979/01/10 Check The Adjustment Of The Original Tachometer Before A New Tachometer Is Installed
1979/01/10 New Switch Assembly Used With Exhaust Gas Recirculation System
1994/07/08 Improved Lubrication Of Attachment Coupler Bushing{5133}
1999/11/01 Download Flash Files By Using The Caterpillar Service Information System (SIS) Or SIS Web{1901,1920}
1979/01/24 Longer Bolts Are Now Used To Fasten The Engine Fan Assembly To The Adapter
1979/01/24 List Of Service Publications
1979/03/07 New Design Fuel Injection Valve Body Used In Fuel Injection Lines Group
1979/03/07 Federal Law Prohibits Tampering With Noise Control Systems
1979/03/07 Stronger Suction Bell Assembly Now Used In Engine Oil Lines Group
1979/03/07 New Larger Capacity Water Separator Is Available
1979/03/07 High Sulfur Fuel Can Cause Severe Engine Wear And Internal Damage
1979/03/07 Engine Mounted Exhaust Brake Systems Can Be Used To Extend Service Brake Life
1979/03/07 New Exhaust Valve And Valve Guide
1979/03/07 New Manifold Assembly Gives More Room For The Lifting Eye
1979/03/07 Engine Valve Springs Are Now Made Of Carbon Steel Alloy
1979/03/07 New Fuel Injection Lines Groups Use A Different Fuel Injection Nozzle Assembly
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.