1989/06/19 Caterpillar


Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}

Usage:


A new Special Instruction, SEHS9014, is available to simplify charging any Cat battery. It contains a rate table and a time table to give all the information needed to select the correct charging rate and time required to charge any Cat battery.

This form is printed on oil resistant paper. It is suitable to display in your battery charging area. Also, you may want to keep a copy at the parts counter. It can improve battery sales by reminding you that a 12 volt battery should read not less than 12.40 volts on a digital voltmeter. Any voltage below 12.40 means the battery needs charging. This applies to batteries being sold or tested.

The time needed to charge a battery depends on the open circuit voltage, which indicates the state of charge. This will be either two, three, or four hours, and is found in the time table for various ranges of open circuit voltages.

Caterpillar Information System:

1989/06/19 Identification Of Asbestos-Free Material{0353,0112,0648}
1989/05/29 "CXP Fluids" Are Now "Cat Fluids" {0645}
1989/05/29 Maintenance Inspection Of Emergency Shutdown Systems Required Every 1000 Hours {7400}
1989/05/29 New Extension Assembly Used In Gas Engine Ignition Groups {1558}
1989/05/29 New Upper and Lower Seals For Folded Core Radiators In Cold Temperature Applications {1353}
1989/05/22 New Clamps With Grommets Used In Fuel Lines, Turbocharger Oil Supply Lines, And Turbocharger Water Supply Lines {1274,1307,1380}
1989/05/22 Check Valve Added To Fuel Injection Lines {1274}
1989/05/22 New Front Crankshaft Seal Requires New Installer Tool {1160,1202,0704}
1989/05/22 Do Not Prefill Secondary Fuel Filter {1261,1290}
1989/05/22 Vibration Measurement System For Caterpillar Products {0781,0783,0784}
1989/05/15 New Installation Procedure For Unit Injectors {1290}
1989/05/15 Front Idler And Accessory Drive Gears Improved {1206,1361}
1989/06/19 New Seal Used In Auxiliary Water Pump Groups{1361}
1989/06/19 New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/26 Air Vent Line Improves Cooling System Performance{1395,1350}
1989/06/26 Change Routing Of Heater Return Hose To Improve Heater Efficiency{7304,1361}
1989/06/26 Damper Groups Improved To Help Prevent Leaks Of Viscous Fluids{1205}
1989/06/26 New Connector With An Orifice Added To Fuel Injection Lines Groups To Help Prevent Cavitation{1274}
1989/07/03 Air Conditioning Service Tooling{0757,0786,7320}
1989/07/03 Use Same Torque For All Sizes Of Threaded Crown Hydraulic Cylinders{5100,7562}
1989/07/10 New Viton Rubber Seals Used{1302,1307,1312,1306,1317,1200}
1989/07/10 New, Larger Vibration Damper Improves Wear Life{1205}
1989/07/17 PEEC Training And Diagnostic Training Program Available{0314,0372,1705}
1989/07/24 New Publication Available, "Metal Spray Guide"{0374}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.