Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
Usage:
The 6V115 Tee Handle Hexagonal Wrench, which is a part of the 5P7335 Rack Adjusting Tool, is now available for parts replacement. The initial (first) quantities of the tee handle hexagonal wrench will be 6.5" (165.1 mm) in length. Later, the length will be changed to 9" (228.6 mm). Later 5P7335 Rack Adjusting Tools will have the 9" (228.6 mm) wrench. The 6V115 Wrench is directly adaptable to applications which need this type of wrench.
NOTE: When a 6V115 Wrench is used with the 5P7335 Rack Adjusting Tool to set the rack on some engines, it must be 6.5" (165.1 mm) in length because of limited clearances. For this reason, it is best to have both a 6.5" (165.1 mm) and a 9" (228.6 mm) length 6V115 Wrench available.
Caterpillar Information System:
1979/09/10 Recommendation For Use Of A FLEX-HONE On 1100, 3100 and 3200 Series Engines {1201}
1979/09/10 Different Grease Fitting Now Used In Fan Drive Group {1359}
1979/09/10 New Gasket Used In Water Lines Group For Aftercooler {1380,1063}
1979/09/10 Undercarriage Disassembly And Assembly Procedures And Specification Charts Are Available {4150,4159,4154,4171,4180}
1979/09/10 6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}
1979/09/10 Stronger Bolt Now Used With Exhaust Manifold {1059,1307}
1979/09/10 Insulation Sleeve For 5P7360 Tach Generator Now Available {7462}
1979/09/03 Different Mounting Hole Locations In Ring Gear Plate Assembly And Rotor Assembly For BrakeSaver{1155}
1979/09/03 Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03 Follow Recommendations Given In Special Instructions For Modification Of Rollover Protective Structures (ROPS) At All Times{7323,7325}
1979/09/03 Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/08/27 New Design Thrust Plate Used In Crankshaft Group{1201,1202,1203}
1979/09/10 Pin Bore Is Now Offset (Not In The Center) .059" (1.5 mm) In The Piston To Stop Vibration Of The Cylinder Liners Which Can Cause Pitting On The Coolant Side Of The Cylinder Liners {1214,1216}
1979/09/10 Engines Can Use Crankshafts With Either Six Or Eight Counterweights {1202}
1979/09/17 New Main And Connecting Rod Bearings Have A Thicker Layer Of Surface Material{1230,1203,1219}
1979/09/17 New BrakeSaver Control Valve Group Has Improved Diaphragm{1159,1155}
1979/09/17 Keystone Piston Groups Can Be Installed In Earlier Engines In Steiger Tractors{1214,1215}
1979/09/17 Raw Water Pump Improved{1371}
1979/09/17 Improved Sea Water Pump Now Used{1361,1371}
1979/09/17 New Bracket Available For Installation Of Jacket Water Heater{1383}
1979/09/17 6V2042 Alignment Yoke And 6V2043 Alignment Bar Available{0653,3305,4450}
1979/09/24 8S9901 Tool Cart Can Be Adapted To Hold Both The 5P3600 Hydraulic Flow Meter Group And The Tools Used With It{0651}
1979/09/24 Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/10/01 New Liner Seat Inserts For Spacer Plate Cylinder Blocks Are Made Of Stainless Steel{1217,1201,0663}