6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}
Usage:
All Engines Equipped With Turbochargers
A 6V2055 High Vacuum Grease is available for use during turbocharger reconditioning. Use 6V2055 High Vacuum Grease in place of 4L7464 Silicone Grease. This high vacuum grease increases the efficiency of the seal rings. It also gives a better oil seal at the turbine end of the turbocharger when the turbocharger is first put into operation.
Use the new grease in the seal ring groove at the turbine end of the wheel and shaft assembly in the reconditioning of all turbochargers.
Typical turbine wheel and shaft. Arrow shows location where high vacuum grease is needed.
Caterpillar Information System:
1979/09/10 Stronger Bolt Now Used With Exhaust Manifold {1059,1307}
1979/09/10 Insulation Sleeve For 5P7360 Tach Generator Now Available {7462}
1979/09/03 Different Mounting Hole Locations In Ring Gear Plate Assembly And Rotor Assembly For BrakeSaver{1155}
1979/09/03 Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03 Follow Recommendations Given In Special Instructions For Modification Of Rollover Protective Structures (ROPS) At All Times{7323,7325}
1979/09/03 Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/08/27 New Design Thrust Plate Used In Crankshaft Group{1201,1202,1203}
1979/08/27 New Rocker Arms And Rocker Arm Shaft Have Improved Lubrication{1102}
1979/08/27 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U. S. Factories{1318}
1979/08/27 6V190 Clamp Is Available For Use On Sleeve Metering Fuel Systems{0626,1250}
1979/08/27 Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27 Exhaust Manifold And Air Lines Groups Changed To Prevent Exhaust Leakage{1059,1061}
1979/09/10 Undercarriage Disassembly And Assembly Procedures And Specification Charts Are Available {4150,4159,4154,4171,4180}
1979/09/10 New Gasket Used In Water Lines Group For Aftercooler {1380,1063}
1979/09/10 Different Grease Fitting Now Used In Fan Drive Group {1359}
1979/09/10 Recommendation For Use Of A FLEX-HONE On 1100, 3100 and 3200 Series Engines {1201}
1979/09/10 Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10 Pin Bore Is Now Offset (Not In The Center) .059" (1.5 mm) In The Piston To Stop Vibration Of The Cylinder Liners Which Can Cause Pitting On The Coolant Side Of The Cylinder Liners {1214,1216}
1979/09/10 Engines Can Use Crankshafts With Either Six Or Eight Counterweights {1202}
1979/09/17 New Main And Connecting Rod Bearings Have A Thicker Layer Of Surface Material{1230,1203,1219}
1979/09/17 New BrakeSaver Control Valve Group Has Improved Diaphragm{1159,1155}
1979/09/17 Keystone Piston Groups Can Be Installed In Earlier Engines In Steiger Tractors{1214,1215}
1979/09/17 Raw Water Pump Improved{1371}
1979/09/17 Improved Sea Water Pump Now Used{1361,1371}