1978/09/11 Caterpillar

New Drive Adapters For Fuel Injection Test Bench{0650}

Usage:

Two new drive adapters are available to test the mechanical overspeed shutoff groups which can not be tested with the 5P7387 Adapter Group. The two new J-23300-965 and J23300-966 Drive Adapters (see Illustration 1) must be ordered from the Kent-Moore Corporation as shown below.

^*ORDER ADAPTERS FROM:

Customer Service Manager
Kent-Moore Tool Division
Kent-Moore Corporation
Jackson, MI 49203

Attention: Diesel and Allied Products Order Desk

The two new drive adapters are also available in the new 5P9737 Adapter Group which is a replacement for the former 5P7387 Adapter Group (see Illustration 2). The new 5P9737 Adapter Group has the tools shown in the chart that follows:

Illustration 1. Drive adapters.

Illustration 2. 5P9737 Adapter Group.

This information will be added to the Special Instruction, Form No. SEHS7281, "Using The Caterpillar Fuel Injection Test Bench", as a supplement, in the near future.

^*Do not send orders to Kent-Moore subsidiaries or their distributors.

Caterpillar Information System:

1978/09/04 New Water Pump Gives More Pressure{1361}

1978/09/04 New Nozzle Assembly Used In Fuel Injection Valves{1254}

1978/09/04 New Gasket Used In Exhaust Manifold Group{1059}

1978/09/04 Correct Procedure To Adjust Front Power Takeoff Clutches{3055}

1978/09/04 New Torque Specification Used On Bolts That Hold The Cylinder Head{1101}

1978/09/04 New Vent Tube For Water Cooled Turbocharger{1380,1052}

1978/09/04 New Camshaft Rear Bearing For The Sleeve Metering Fuel System{1253}

1978/08/28 Different O-Ring Seals Now Used In Fuel Injection Pump Group{1251}

1978/08/28 New Oil Supply Line And Gasket For Turbocharger{1307,1052}

1978/08/28 New 5P8744 Adapter Assembly And Special Instruction Procedures For 5P4150 Nozzle Tester Group{0650}

1978/08/28 New Design Seals Decrease Shaft Wear In Fuel Transfer Pump{1256}

1978/08/28 Change In Procedure To Check Main Bearing Clearance{1203}

1978/09/11 New Diaphragm Used In Mechanical Shut-Off Groups Has Identification For Correct Installation{7418}

1978/09/11 Correct Installation Of Crankshaft Thrust Plates Is Very Important To Prevent Engine Damage{1203}

1978/09/18 Tips For Service Information Retrieval System (SIRS) Users{0374}

1978/09/18 Permanent Installation Quick Disconnects For Pressure Testing Now Available{0651}

1978/09/25 New Springs Available For Forward And Reverse Clutches, And New Tool To Correctly Position The Clutches Of Twin Disc MG514 Marine Transmission{3302,0626}

1978/09/25 Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}

1978/09/25 Tips For Service Information Retrieval System (SIRS) Users{0374}

1978/09/25 Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}

1978/09/25 New 6V1 Seal Kit Available For Service Repair Of High Pressure Tee Test Couplers{0623,7555,5057}

1978/10/09 Never Use Copper Tubing As A Replacement For Steel Brake Lines{4257,7554}

1978/10/09 Salvage Of Turbocharger Compressor Housing During Reconditioning{1052}

1978/10/09 4J7533 O-Ring Seals Now Available For Parts Service Of The 5P4150 Nozzle Tester Group{0651}