1978/01/09 Caterpillar

5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster{0621,1216}

Usage:

All Caterpillar-built Engines, Except 1100 and 3100 Series Engines and 3208 Engines

The 5P8665 Cylinder Liner Puller is available to remove cylinder liners from all Caterpillar Engines that use cylinder liners. This new tool is easy to install and remove. An impact wrench with a .50" (12.7 mm) drive will have enough force to remove the liners. Generally, less than 10 seconds is needed to remove each liner.

The arm assemblies on the puller are adjusted to fit the length of the liner to be removed. They are then pushed together and installed into the cylinder liner. The spring loaded arms are then moved out so the feet on the ends of the arm assemblies are under the bottom of the liner. The bolt is turned clockwise to remove the liner.

The 5P8665 Cylinder Liner Puller can remove cylinder liners with dimensions up to 7.00" (177.8 mm) in diameter and 18.00" (457.2 mm) in length.

The separate parts of the 5P8665 Cylinder Liner Puller are available to make repairs if necessary (see the Illustration).

5P8665 Cylinder Liner Puller.

Caterpillar Information System:

1978/01/09 Improved Seal Used Between Impeller And Bearings On Water Pump Shaft{1361,1371}

1978/01/09 Service Tip: Use Caution When Hydraulically Operated Implements Must Be Lifted With A Hoist While The Engine Is Stopped{5050}

1978/01/09 Improved Water Pump Group Now Used{1361}

1987/12/21 New or Updated Drive Train Information Available In Guidelines For Reusable Parts{0374}

1987/12/21 New Gerotor Pump Group Used In 3161 Governors{1264}

1987/12/21 New Suction Bell Assemblies, Bolts, And Washers Used In Sump Oil Lines Groups{1307,1315,1304}

1987/12/21 Check Screen Assembly In Fuel Transfer Pump Inlet If Low Fuel Pressure Is Experienced{1256}

1987/12/21 Improved VR3 Voltage Regulator Available For Earlier Generators{4474}

1987/12/14 Earlier Flywheel Housings Can Be Modified For Use With Later Crankshafts{1157,1202}

1987/12/14 New 1U5803 Connector Repair Kit Available{0785,0782}

1987/12/14 Improved Valve Mechanism Cover Groups{1107}

1987/12/14 Cooling System Troubleshooting Procedures For Generator Sets Equipped With Folded Core Radiators{1350}

1978/01/09 Inner Member Of Caterpillar Coupling Must Be Restrained If The Connection To The Inner Member Is Removed{3252}

1978/01/09 Improved Water Shield For Exhaust Manifold{1067}

1978/01/16 Improved Front Pulley And Damper Groups Use New Damper Adapter With Larger Diameter Bolt Circle For Pulley Bolts{1205}

1978/01/16 Tolerance Added To Valve Clearance Specifications{1105,0374}

1978/01/16 New Turbine Housings Are The Replacement For Three Former Turbine Housings Used On Schwitzer Turbochargers{1052}

1978/01/16 Turbine Housing For Turbocharger Is Stronger{1052}

1978/01/16 Improved Gasket Prevents Oil Leakage From The Governor{1264}

1978/01/23 Design Of Governor Control Linkage Changed; Less Force Is Needed To Move The Accelerator Pedal{1265,1269}

1978/01/23 Change In Design Of Engine Governor, Fuel Injection And Transfer Pump Groups, And Fuel Ratio Control Groups{1264,1278,1286}

1978/01/30 Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}

1978/01/30 Oil Strainer (Screen) Added To Turbocharger Thrust Bearing{1052,1053}

1978/01/30 New Water Pump Cover Has A Baffle And Wall To Send Coolant Flow From Bypass Line Directly Into Water Pump{1361}