1986/10/27 Caterpillar


New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}

Usage:


All Engines Except 3600 Family Of Engines

A new 8T2700 Blowby/Air Flow Indicator Group is available and replaces the former 9S7373 Air Meter Group which has been canceled. The new group contains a hand-held digital indicator, a remote mounted pickup, 915 mm (3 ft) of cable, a blowby hose, and the necessary connections. See Illustration 1. The new group can measure the volume of exhaust gases coming out the crankcase breather or the air velocity through the radiator. The former group measures only radiator air velocity.

The digital indicator is battery powered and can also be powered with external 11 to 40 Volts DC from the machine battery, or AC powered with the optional converter.


Illustration 1. The blowby/air flow indicator group in its compact carrying case.

The volume of exhaust gases, or blowby, coming out the engine breather(s) can be very helpful in planning engine repairs. Blowby volume guidelines for Cat engines are listed in the Special Instruction that comes with the instrument. The volume of blowby gases can be shown in either liters/min or cubic feet per hr. Air velocity through the radiator core helps to quickly find areas that are plugged or partially restricted. The flow velocity can be shown in either meters/min or ft/min. Illustration 2 shows the indicators on the face of the instrument. A digital value appears when the instrument is used.


Illustration 2. The meter connected to the blowby pickup.

There are also three optional items that can be ordered to use with the new blowby/air flow instrument. See Illustration 3. These items are:

... 5P7366 Power Cable for connecting machine batteries (11 to 40 Volts DC) to the hand-held indicator.

... 8T5268 Converter. This converts 110/220 Volts AC, 50/60 Hz, power supply to 11 to 20 Volts DC at .3 Amp maximum for powering the indicator.

... 6V2198 Extension Cable, 5500 mm (18 ft) long for operating the indicator more than one meter (3 ft) from the pickup.


Illustration 3. The optional items that are not part of the 8T2700 Group.

Presently, preliminary operating instructions come with the group.

Caterpillar Information System:

1986/10/27 Stronger Oil Level Guide Used{1326,1300}
1986/10/27 Check Oil Drain Hole In OR2671 Or OR2621 Remanufactured Cylinder Heads If Head Used With Breather{1100,1300,1317}
1986/10/20 Check Connecting Rods After Engine Failures Involving Hydraulic Lock{1218,1225}
1986/10/20 Caterpillar Crankshaft Heat Code Locations{1202}
1986/10/20 Orifice Screen Assembly Now Used For The Timing Advance Mechanism{1251,1272,1288,1292}
1986/10/20 New Oil Pump Relief Valve Guide{1304}
1986/10/13 Remanufactured Final Drive Hubs And Housings (U.S. And Canada){4000,4002,4054}
1986/10/13 Water Level Switch Improved{1354,1350}
1986/10/13 New Piston Oil Ring Gives Better Oil Control{1215}
1986/10/13 New Service Tools Available{0600}
1986/09/29 Improved Damper Guard Used{1205}
1986/09/29 Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/11/03 Custom Product Microfiche Library Is Now Part Of U.S. Product Parts Book Library {0374}
1986/11/03 New Jacket Water Heaters Have Longer Thermostat Life {1383,1450}
1986/11/03 High Loads Require Additional Oil Capacity {1318,1214,1215}
1986/11/03 Two New Cold Weather Fuel Heaters Available {1296}
1986/11/03 Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/10 Caterpillar Antifreeze Now Used And Available From Parts Departments{1350,1395}
1986/11/10 New Fuel Ratio Control Used{1278}
1986/11/10 Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10 Use Gas Detector Tubes That Have Expired Dates To "Break In" The Combustion Chambers For The Fuel Sulphur Analyzer Group{0651}
1986/11/24 Smaller Diameter Fuel Supply Line May Cause Power Loss{1274,1250}
1986/11/24 Updates To The Parts Book Microfiche{0374}
1986/11/24 Engine Mounts Available To Provide Clearance For Deep Oil Pans{1152,1302}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.