1982/11/29 Caterpillar


New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}

Usage:


A 6V7059 Multiple Anvil Micrometer is now available. The new micrometer can be used to measure the thickness of cylinder liner top flanges and engine valve lips. It can also be used to measure parts that do not fit a standard micrometer. The micrometer has two anvils that can be removed. These anvils will measure areas not possible to measure with a standard micrometer.

Before you use a cylinder liner again, measure the thickness of the top flange. The minimum thickness for a cylinder liner top flange is in the Specifications Module of the Service Manual.

Check liner projection at assembly as described in the Service Manual.

If you use the micrometer with a 6V2034 Adapter it will measure engine valve lips. Accurate measurements are important if you want to use the valve again. Minimum valve lip thickness dimensions are in the Guideline for Reusable Parts - Valves and Valve Spring Specifications, Form SEBF8034-03.

The 6V7059 Micrometer can be used on all Caterpillar cylinder liners and all Caterpillar engine valves with 30° and 45° valve faces. It can also be used as a general purpose 0 to 25 mm micrometer.


Use the 6V7059 Micrometer with a 6V2034 Adapter to measure the thickness of a valve lip.

Caterpillar Information System:

1982/11/29 Hose Presses Can Now Be Used To Service 12.7 mm (.50") JIC Couplings {0623,0624,7554}
1982/11/29 Transmission Pump Failure Can Be Caused By Worn Splines Or Slot In Pump Drive {3153}
1982/11/29 Inspection Of Equipment After It Has Been In Storage {0355}
1982/11/29 Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29 Improvements Made To Fuel Ratio Control {1278}
1982/11/22 Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22 New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22 Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22 6V4869 Adapter And 6V6174 Plug Can Be Used To Install Camshaft Bearings{1211,0621}
1982/11/15 Repair Kits Available For Air Compressor{1803}
1982/11/15 Crankshaft Has Step At Front Of No. 1 Main Bearing Journal{1202}
1982/11/15 Make Change To 6V2100 Multitach And 5P9698 Calibrator{0651}
1982/11/29 New 6V6146 Load Leveler Can Lift Larger Components {0644}
1982/11/29 Removal Of Water Pump Impeller {1361}
1982/11/29 New Flexible Coupling Group Must Be Installed Correctly {3300,3252}
1982/11/29 6V7013 Rivet Roll Set Now Available {0613,0622,3012}
1982/12/13 6V6190 Gauge Group Can Be Used To Measure Track Roller And Link Wear{0653}
1982/12/13 New Piston Group Has A Thicker Top Ring{1215,1214,1213,1225,1226,1227}
1982/12/20 Dimensions For Reconditioning Cylinder Blocks, Cylinder Heads{1201,1101,1103,1105}
1982/12/20 Replacement Seal Group For Raw Water Pump Shaft Now Has All The Seal Parts Plus An Installation Tool{1371,0622}
1982/12/20 New Piston Design Decreases Oil Consumption{1214,1215}
1983/01/10 Water Pump Impellers Can Be Reconditioned{0661,1361}
1983/01/10 Changes In Engine RPM; Governor Does Not Operate Correctly{1264}
1983/01/10 Spring Seat Enlarger Available For Use On Cylinder Heads{0663}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.