1980/01/28 Caterpillar


Oil Drain Hole Added To Spacer Plate Cylinder Block To Permit Use Of Scroll Fuel System{1201,1221}

Usage:


All Direct Injection 3306 Engines With Scroll Fuel Systems

Description of Change: An oil drain hole has been added to the spacer plate cylinder blocks for direct injection 3306 Engines. This oil drain hole, which is in the fuel pump mounting area, permits use of the scroll fuel system on direct injection 3306 Engines.

The spacer plate block will have a plug in the oil drain hole when used with a sleeve metering fuel system.

The scroll fuel system cannot be used on counterbore cylinder block.

Caterpillar Information System:

1980/01/28 New Attachment Air Compressor Group and Lines Groups Have Improved Design{1065}
1980/01/28 Installation Procedures For 5N5880 Remote Shut-Off Group And 5N6336 Oil Pressure Indicator Gauge Group{7418,7403,7455}
1980/01/28 New 6V199 Socket For Use On Fasteners In Areas With Limited Clearance{0612}
1980/01/21 New Fuel Injection Nozzle Assembly Used{1254}
1980/01/21 Extended Shafts Now Available For Front Power Takeoff Units{3055}
1980/01/21 Cooling System Improvements Prevent Expansion Tank Leakage{1354,1380,1153}
1980/01/21 New Piston Groups Have The Piston Pin Bore Off-Center, Away From The Thrust Side Of The Piston{1214}
1980/01/21 A Spring With A Lower Rate Is Now Used In The Fuel Filter Group To Give Less Fuel Pressure{1261}
1980/01/14 New Raw Water Engine Oil Cooler Is Used{1378}
1980/01/14 Use The FT1481 Bracket To Hold The 1P2371 Micrometer In Position During Bore Size Measurement{0655,0663}
1980/01/07 Improved Ring Seal Used At Rear Of Crankshaft {1161}
1980/01/07 8N1831 Fuel Nozzle Assembly Now Approved For Use In 1693 Truck Engine; Chart For Applications Of 8N1831 And 7N5005 Fuel Nozzle Assemblies {1254}
1980/02/04 New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower{1216}
1980/02/04 Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04 Real Value Available Through Caterpillar Remanufacturing Programs{0374}
1980/02/11 Warning: Avoid Use Of Fuel Mixtures Of High Volatility. If You Are Exposed To Such Mixtures, Be Aware Of The Hazards Involved And Take Proper Precautions{1280}
1980/02/11 Use The Correct Water Temperature Contactor{1350,1100}
1980/02/25 How To Check Operation Of Hydramechanical Shutoffs On D379B, D398B, D399 Engines{7418}
1980/02/25 Revision Of Special Instruction Form No. SMHS7267, "Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets" Has Important Changes{1307}
1980/02/25 Stronger Braces Used Between Air Cleaner And Engine{1051}
1980/02/25 Plunger Movement Must Be Adjusted When New Rack Shut-Off Solenoid Is Installed{1259}
1980/02/25 Drawings Available For Six Tools Used During Repairs Of Damaged Pin Bores In Two-Piece Booms{6501,0665}
1980/02/25 Identification Of Fuel Injection Lines And Nozzle Bodies For Different Combustion Systems{1252,1254}
1980/03/03 Spacer Plate Block Group Used For Parts Service Of Block Group With Counterbore Design{1101,1201}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.