Installation Procedure For The 136-4304 Wiring Harness Assembly{1090} Caterpillar


Installation Procedure For The 136-4304 Wiring Harness Assembly{1090}

Usage:

3306C (7RJ, 9TL) Truck Engines

Introduction

Do not perform any procedure outlined in this Special Instruction or order any parts until you have read and understood the information contained within.

Parts Needed


Diagram for replacement of the 101-9643 with the 138-3318 Control. (1) 138-3318 Control. (2) Wire identification using the codes from the 101-9643 Control to the 136-4304 Wiring Harness Assembly. (3) 5W-1982 Terminal. (4) 136-4304 Wiring Harness Assembly. (5) 102-8811 Plug Kit. (6) 127-5485 Connecting Plug Assembly. (7) OEM wiring harness.

Installation

1. Disconnect the battery.

2. Disconnect the wiring harness from the 101-9643 Control. Remove the 101-9643 Control from the Mounting Bracket.


Illustration 2. Wiring identification using codes from the 101-9643 Control to the OEM wiring harness.

3. Inspect, verify and correct the wire colors indicated in Chart 2. See Illustration 2.

4. Cut off the 4 pin and 6 pin connectors that connect to the 101-9643 Control from the OEM wiring harness.


Illustration 3. (6) 127-5485 Connection Plug Assembly. (7) 8N-1543 Connection Socket.

5. Identify the FGK wire to the glow plug and assemble the 127-5485 Connection Plug Assembly (6) with the 8N-1543 Connection Socket (7) (for the 10 AWG wire). Use the Deutsch© crimp tool or a heavy duty standard crimping tool in order to attach the socket to the wire.


Illustration 4. Assembly of the 5W-1982 Terminal. (3) 5W-1982 Terminal.

6. Identify wire 30 (main power supply) and assemble the 5W-1982 Terminal (3) to the stripped end of the wire using a standard crimping tool.


Illustration 5. 102-8811 Plug Kit. See Chart 3.

7. Connect the remaining OEM wiring harness wires to a 102-8811 Plug Kit using the 9W-0844 Connection Sockets (for 14/16 AWG wire). Seal the Socket 8 hole with an 8T-8737 Seal Plug. See Chart 3 in order to locate the wires in the connector properly, and use the 1U-5804 Crimp Tool to connect the 9W-0844 Sockets to the wires.


Illustration 6. Views of the 138-3318 Control. The 138-3318 Control should be mounted with the connector pointed downward as in the illustration.

8. The two mounting holes are not the same when switching from the 101-9643 to the 138-3318 Control. Modify the mounting bracket in the OEM Truck chassis in order to install the 138-3318 Control with two M6 (1/4in) thread bolts at a spacing of 99.5 ± 1.5 mm (3.92 ± .06 in) on a horizontal plane.


NOTICE

The 138-3318 Control should be installed with the connector pointed downward in order to minimize water damage. See Illustration 6.


9. Install the 5W-1982 Terminal (3) on the wire 30 to the M6 stud on the 133-3318 Control with the nut that is supplied. An equivalent 5C-2890 Nut can be used.

10. Install the 133-3318 Control to the OEM truck chassis modified mounting bracket using two M6 or two 1/4 inch bolts with washers.

11. Connect the 136-4304 Harness Assembly to the 133-3318 Control.

12. Connect the prepared OEM wiring harness connectors from steps 5 and 7 to the 136-4304 Harness Assembly connectors. Make sure the two parts "snap" together.


Illustration 7. Instrument panel indicator lamp wiring diagram. (8) 8D-1429 Miniature Lamp.

13. The instrument panel indicator lamp is connected to wires L and 31. Cut wire 31 and connect the cut lead coming from the lamp to the key switch (key ON position). In order to prevent a short, make sure to insulate the other end of wire 31. Wire 31 is connected to ground, but is no longer used. See Illustration 7.

14. Replace the existing light bulb with an 8D-1429 Miniature Lamp (8). The lamp size must not exceed 2 watts in order to operate properly with the new 133-3318 Control.

15. Test the system for proper operation. Refer to, Special Instruction, SEHS9773; "Installing The 104-7618 Intake Manifold Heater"

Caterpillar Information System:

Conversion Of Generators From Self-Excited To Permanent Magnet{4450} Conversion Of Generators From Self-Excited To Permanent Magnet{4450}
PTO Installation And Applications Instruction{1165} PTO Installation And Applications Instruction{1165}
Repair Procedure: 3600 Series Cylinder Heads - Blended Fuel{1100} Repair Procedure: 3600 Series Cylinder Heads - Blended Fuel{1100}
Instructions For EMCP II+ Field Retrofit Onto EMCP II Equipped Generator Sets{7490, 7451} Instructions For EMCP II+ Field Retrofit Onto EMCP II Equipped Generator Sets{7490, 7451}
Installing the Air Inlet Heater System{1090} Installing the Air Inlet Heater System{1090}
Generator Set Start-up Checklist{1021, 1404, 7002} Generator Set Start-up Checklist{1021, 1404, 7002}
Calibrating The 133-8985 Governor And Fuel Injection Pump Group Heavy Sleeve Metering Fuel System (HSMFS){650, 1250} Calibrating The 133-8985 Governor And Fuel Injection Pump Group Heavy Sleeve Metering Fuel System (HSMFS){650, 1250}
Installation Procedure For The 138-7020 Harness Assembly{1408} Installation Procedure For The 138-7020 Harness Assembly{1408}
5.4" BORE, 60 V12 VEHICULAR ENGINE V-Belt Tension Chart
5.4" BORE, 60 V12 VEHICULAR ENGINE Voltmeter
5.4" BORE, 60 V12 VEHICULAR ENGINE Shut-Off Solenoids
5.4" BORE, 60 V12 VEHICULAR ENGINE Starter Magnetic Switches
Improved Straight-Faced Wiper Seals{7555, 7562} Improved Straight-Faced Wiper Seals{7555, 7562}
WOODWARD REPAIR MANUAL FOR DIASSEMBLY AND REASSEMBLY PROCEDU Chapter 1. 120 mm Throttle Valve with Actuator Parts
WOODWARD REPAIR MANUAL FOR DIASSEMBLY AND REASSEMBLY PROCEDU Chapter 2. 120 mm Throttle Valve with Actuator Disassembly
WOODWARD REPAIR MANUAL FOR DIASSEMBLY AND REASSEMBLY PROCEDU Chapter 3. 120 mm Throttle Valve with Actuator Reassembly
Caterpillar Post Installation Compatibility Assessment for Stationary Engines Caterpillar Post Installation Compatibility Assessment for Stationary Engines
Caterpillar Post Installation Compatibility Assessment for *NEW* Stationary Engines Caterpillar Post Installation Compatibility Assessment for *NEW* Stationary Engines
Cat� Retrofit Selective Catalyst Reduction System Commissioning Report Cat� Retrofit Selective Catalyst Reduction System Commissioning Report
Compressed Air Packaged System Compressed Air Packaged System
High Pressure Fuel Pump Return Form High Pressure Fuel Pump Return Form
3176C & 3196 MARINE ENGINES Systems Operation
3176C & 3196 MARINE ENGINES Testing & Adjusting
BENDIX AIR COMPRESSOR 1W150R AIR COMPRESSO Introduction
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.