PRODUCT SUPPORT PROGRAM FOR REWORKING THE PRIMARY AND SECONDARY THROTTLE CIRCUITS ON CERTAIN C32 MARINE ENGINES Caterpillar

PRODUCT SUPPORT PROGRAM FOR REWORKING THE PRIMARY AND SECONDARY THROTTLE CIRCUITS ON CERTAIN C32 MARINE ENGINES

Usage:

REBE9814-00

Show/hide table

03Jun2013

U-232

D-201

O-201

TM-8

Show/hide table

*Before/After*	PRODUCT SUPPORT PROGRAM FOR REWORKING THE PRIMARY AND SECONDARY THROTTLE CIRCUITS ON CERTAIN C32 MARINE ENGINES
1408		PS43921

Show/hide table

NOTE:

This Program must be administered either before or after failure. In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS43921" as the Part Number and "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.

Show/hide table

NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

Show/hide table

TERMINATION DATE

30Jun2015

PROBLEM

Show/hide table

The existing primary and secondary throttle circuits are configured incorrectly on certain C32 marine engines listed in this program. The existing harness configuration will not provide a throttle signal to the engine.

AFFECTED PRODUCT

Show/hide table

Model

Identification Number

C32

RNX00545, 549-550, 569, 572, 613, 627-632, 640, 646, 652, 655-656, 660, 665, 678-679, 683-694, 696, 711-715, 721, 726, 728-734, 740, 745, 747-749, 752, 755-757, 761-762, 764-767, 772, 778-780, 782-786, 805-806, 816-817, 820, 824

RNY01398, 1536, 1541, 1708-1710, 1744, 1746, 1750, 1752, 1769, 1789, 1794-1796, 1798-1800, 1803-1804, 1808, 1816, 1836, 1847, 1854-1855, 1864, 1867-1868, 1872-1875, 1878-1881, 1885-1887, 1889, 1892, 1895, 1897, 1900, 1913-1914, 1916-1917, 1919-1920, 1925-1926, 1958, 1962-1963, 1966, 1970, 1989, 1998, 2002, 2005, 2008-2013, 2015-2016, 2022, 2031, 2037, 2039-2040

RNZ00886-00887, 889, 892, 901, 904, 974, 997, 1000-1001, 1003-1004, 1026, 1033-1036, 1074, 1077, 1081, 1083, 1085, 1098, 1105-1106, 1110-1112, 1144, 1146-1148, 1150-1151, 1157-1158, 1160, 1167, 1175

PARTS NEEDED

Show/hide table

Qty	Part Number	Description
14	9X1813	SLEEVE-BULK (14 CM)
4	1261767	PIN-CONNECTOR
1	WIRE	16 GUAGE WIRE (32 CM)
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 29% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table

This service letter should only be performed before or during the initial vessel commissioning sea trial.

Refer to Special Instruction, REHS8175, "Procedure to Rework Primary and Secondary Throttle Circuits on Certain C32 Marine Engines".

Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table

Product smu/age whichever comes first	Caterpillar		Dealer Suggested		Customer Suggested
Product smu/age whichever comes first	Parts %	Labor Hrs%	Parts %	Labor Hrs%	Parts %	Labor Hrs%
0-40 hrs, 0-24 mo	100.0%	100.0%	0.0%	0.0%	0.0%	0.0%

Show/hide table

NOTE: This is a 1.0-hour job
No travel permitted. This repair is to be performed before or during the vessel commissioning sea trial. A $10 Miscellaneous charge is allowed for 32 cm of 16 gauge wire.

Show/hide table