Catalyst (SCR) - Remove and Install
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
Show/hide table
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury. |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 399-9725 | Handle As | 1 |
B | Loctite™ Nickel Anti-Seize | - |
Show/hide table
Illustration 1 | g06278098 |
Show/hide table
Illustration 2 | g06278114 |
Show/hide table
Illustration 3 | g06278119 |
Show/hide table
Illustration 4 | g06278126 |
Repeat for inner catalyst |
Show/hide table
Illustration 5 | g06278134 |
Install the rear seal between the tube and the inner catalyst assembly . |
Show/hide table
Illustration 6 | g06278141 |
Install the outer catalyst seal between the inner and outer catalyst assemblies. |
Show/hide table
Illustration 7 | g06278143 |
Show/hide table
Illustration 8 | g06278156 |
Show/hide table
Illustration 9 | g06278160 |
Show/hide table
Illustration 10 | g06278163 |
Show/hide table
Illustration 11 | g06278165 |
Note: Tighten the cover bolts starting in the middle and working towards the corners.
Caterpillar Information System:
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Monitoring System
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Camera - If Equipped
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Air Cleaner - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Battery Disconnect Switch
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuel Tank Cap - Clean
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Operator Controls
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Windows - Clean
New Software Is Now Used for Certain 7 Inch and 13 Inch Cat® Marine Displays {7490, 7490} New Software Is Now Used for Certain 7 Inch and 13 Inch Cat® Marine Displays {7490, 7490}
A New Duplex Oil Filter Lever Linkage Assembly is Now Used on Certain 3500 Marine Engines {1306, 1308} A New Duplex Oil Filter Lever Linkage Assembly is Now Used on Certain 3500 Marine Engines {1306, 1308}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Window Washer Reservoir - Fill
320 GC, 320 and 323 Excavator Machine Systems Assist - Calibrate - Additional Fine-Tuning for Grade Assist
C7.1 Marine Propulsion Engine Camshaft Position Sensor - Remove and Install
C9.3B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Fuel Transfer Pump (Refueling) - If Equipped
Shutdowns May Occur with NOx Sensor Diagnostic Codes Present on Certain CG137, G3400, G3500, and G3600 Gas Engines {191N, 7432} Shutdowns May Occur with NOx Sensor Diagnostic Codes Present on Certain CG137, G3400, G3500, and G3600 Gas Engines {191N, 7432}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Radio
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Air Conditioning and Heating Control
New Rotary Switch is Now Used for MECP1 Panel on Certain Engines {7451} New Rotary Switch is Now Used for MECP1 Panel on Certain Engines {7451}
C18 Generator Sets Generator - Dry
C9 Generator Set Generator Bearing - Inspect
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Electrical Connections - Check
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Main Hydraulic Pump Air - Purge
C18 Generator Sets Single Unit Operation
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Engine Performance - Test - Engine Speed