Exhaust Elbow - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove heat shields (1) and (2) from the exhaust elbow assemblies.
Show/hide table
Illustration 2 g06239998 - Remove nuts (4), elbow assembly (3), and the gasket.
Show/hide table
Illustration 3 g06240043 - Remove nuts (6), elbow assembly (5), and the gasket.
Show/hide table
Illustration 1 | g06239987 |
- Install the gasket, elbow assembly (5), and nuts (6).
Show/hide table
Illustration 5 g06239998 - Install the gasket, elbow assembly (3), and nuts (4).
Show/hide table
Illustration 6 g06240049 Note: Ensure that the heat shields are clean and free from damage. If the heat shields are worn or damaged, replace with the new heat shields.
- Install shield (2) on elbow assembly (5). Install shield (1) on elbow assembly (3) and also partially covering shield (2).
Note: Tighten and adjust the heat shields by using the straps and the D-rings.
Show/hide table
Illustration 4 | g06240043 |
Caterpillar Information System:
The Buffer Seal Groove May Wear on the Steering Cylinder Head on Certain 773G and 777G Off-Highway Trucks {4303} The Buffer Seal Groove May Wear on the Steering Cylinder Head on Certain 773G and 777G Off-Highway Trucks {4303}
336, 336 GC and 340 Excavator Systems Stick Cylinder
320GC and 320 Excavator Engine Supplement Nitrogen Oxide Sensor - Remove and Install
C32 Marine Engines Inlet Air Temperature Sensor - Remove and Install
C32 Marine Engines Inlet Manifold Pressure Sensor - Remove and Install
C32 Marine Engines Speed/Timing Sensor - Remove and Install
320GC and 320 Excavator Engine Supplement Manifold (DEF Heater) - Remove and Install
336, 336 GC and 340 Excavator Systems Bucket Cylinder
XQ125 Generator Set Cooling System Coolant Level - Check
XQ125 Generator Set Belt Tensioner - Inspect
XQ125 Generator Set Cooling System Coolant (DEAC) - Change
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Sensor Supply - Test - Display
C7.1 Engines Coolant Pressure Is Low
336, 336 GC and 340 Excavator Systems Pilot System
C32 Marine Engines Electronic Control Module - Remove and Install
794 AC Off-Highway Truck Magnetic Plug (Wheels) - Check
A New Service Replacement Control Board (APC1+) is Now Used on Certain Cat® Uninterrupted Power Supply {1418, 4480} A New Service Replacement Control Board (APC1+) is Now Used on Certain Cat® Uninterrupted Power Supply {1418, 4480}
New Improved Gearbox Oil Heater is Now Used on Certain G3512E, G3516H, G3520C, and G3520H Generator Sets {1333} New Improved Gearbox Oil Heater is Now Used on Certain G3512E, G3516H, G3520C, and G3520H Generator Sets {1333}
New Jacket Water Bypass Tube is Now Used on Certain C175-20 Locomotive Engines {1380} New Jacket Water Bypass Tube is Now Used on Certain C175-20 Locomotive Engines {1380}
C32 Tier 4 Final Marine Commercial Engines DEF Pump Motor - Test
A New Plate-Type Heat Exchanger is Now Available for Certain Cat® 3516C Marine Engines {1379} A New Plate-Type Heat Exchanger is Now Available for Certain Cat® 3516C Marine Engines {1379}
A New Heat Shrink is Now Used for Certain Cat Electronic Control Module (ECM) Resistors {0644, 1901} A New Heat Shrink is Now Used for Certain Cat Electronic Control Module (ECM) Resistors {0644, 1901}
320GC, 320 and 323 Excavators Machine Systems Swivel - Remove and Install
794 AC Off-Highway Truck Electric Drive Pump (Powered Stairway) Oil - Change - If Equipped