854K Wheel Dozer Systems Caterpillar


Oil Filter (Case Drain)

Usage:

854K KK3


Illustration 1g06215919

Table 1
Item  Qty  Part  Specification Description 
Final installation torque to 35 ± 3 N·m (26 ± 2 lb ft)
1G-8878 Oil Filter  Before assembly, lubricate seal with clean hydraulic oil. Install oil filter until seal makes first contact with sealing surface.
Tighten by half a turn. 
Maximum operating pressure is 2758 kPa (400 psi).
Pressure setting for the bypass valve is 172 kPa (25 psi)

Caterpillar Information System:

854K Wheel Dozer Systems Hydraulic Tank and Mounting
The Engine Oil Filter Group is Improved on Certain 627K and 637K Wheel Tractor Scrapers {1306, 1308} The Engine Oil Filter Group is Improved on Certain 627K and 637K Wheel Tractor Scrapers {1306, 1308}
C9.3B Engines for Caterpillar Built Machines Belt Tensioner - Remove and Install
MD6200 Rotary Drill Fuses - Replace
C9.3B Engines for Caterpillar Built Machines Inlet Manifold Pressure Sensor - Remove and Install
Next Generation Hydraulic Excavator Monitoring System Prestart Monitoring Function
A New Spacers in the Steering Cylinder Group Are Now Used on Certain Wheel Skidders {4303} A New Spacers in the Steering Cylinder Group Are Now Used on Certain Wheel Skidders {4303}
330 GC and 330 Excavator Diesel Exhaust Fluid Injector - Replace - C7.1 Engine
990K Wheel Loader Systems Exhaust Lines
990K Wheel Loader Systems Final Drive and Wheel
AD22 Underground Articulated Truck Braking System Brake Cooling Pressure - Check
AD22 Underground Articulated Truck Braking System Brake Disc Wear - Check
854K Wheel Dozer Systems Oil Filter (Hydraulic) - Fan
844K Wheel Dozer Systems Lift Cylinder
D9R Track-Type Tractor Systems Bulldozer Tilt Cylinder
986K Wheel Loader Systems Oil Filter (Hydraulic) - Pilot Lines
D9R Track-Type Tractor Systems Bulldozer Tilt Cylinder
844K Wheel Dozer Systems Steering Control
A Turbocharger Inlet Hose Heat Shield Is Now Used on Certain 930K and 938K Wheel Loaders {1067, 1071} A Turbocharger Inlet Hose Heat Shield Is Now Used on Certain 930K and 938K Wheel Loaders {1067, 1071}
MD6250 Rotary Drill Systems Location of Components
320, 323 Excavator Engine Supplement Fuel Filter and Base - Remove and Install
Inertial Measurement Unit (IMU) Sensors are Now Isolation Mounted on Certain 631K and 637K Wheel Tractor-Scrapers {1408, 1439} Inertial Measurement Unit (IMU) Sensors are Now Isolation Mounted on Certain 631K and 637K Wheel Tractor-Scrapers {1408, 1439}
Improved Shaft Bearings for Drive Pumps are Now Used on Certain D6K and D6K2 Track-Type Tractors, and 953D Track-Type Loaders {3203, 5070} Improved Shaft Bearings for Drive Pumps are Now Used on Certain D6K and D6K2 Track-Type Tractors, and 953D Track-Type Loaders {3203, 5070}
How to Check SCV Current in Cat Electronic Technician (ET) on Certain C3.3B Tier IV Final and C3.8 Tier IV Interim Engines {1920} How to Check SCV Current in Cat Electronic Technician (ET) on Certain C3.3B Tier IV Final and C3.8 Tier IV Interim Engines {1920}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.