Exhaust Bypass Valve - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关收集和盛接 Cat ® 产品油液的合适工具和用品,请参考专门出版物 NENG2500 "代理商维修工具目录"。 按照本地法规和要求处置所有油液。 |
- 将冷却系统中的冷却液排入适当的容器直至液位低于排气旁通阀,以便保存或废弃。 请参考操作和保养手册,"冷却系统冷却液 - 更换"。
Show/hide table
图 1 g06151917 - 拆下 11 个螺栓 (2),然后拆下护罩 (1)、 (3) 和 (4)。
Show/hide table
图 2 g06151954 - 拆下 13 个螺栓 (6) 后拆下护罩 (5)。
Show/hide table
图 3 g06152213 - 拆下 12 个螺栓 (9),然后拆下护罩 (7)、 (8) 和 (10)。
Show/hide table
图 4 g06152245 - 拆下 14 个螺栓 (14),然后拆下护罩 (11)、 (12) 和 (13)。 两个螺栓未显示。
Show/hide table
图 5 g06152261 - 拆下 14 个螺栓 (15) 后拆下护罩 (16)。 五个螺栓未显示。
Show/hide table
图 6 g06152285 - 拆下 16 个螺栓 (17) 后拆下护罩 (18)。 10 个螺栓未显示。
Show/hide table
图 7 g06152304 - 拆下三个螺栓 (19) 并拆下护罩 (20)。
Show/hide table
图 8 g06152444 - 拆下两个螺栓 (21),然后拆下护罩 (22)。
Show/hide table
图 9 g06152450 - 拆下保温层 (23)。
Show/hide table
图 10 g06152452 - 断开 3 个回转螺母 (24),然后拆下 4 个螺母 (25)。
- 拆下排气旁通阀 (26)。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 2P-2333 | 密封胶 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 放置排气旁通阀 (26)。
- 如果已安装排气旁通阀 (26) 的螺柱,将螺柱拧紧至扭矩 35 ± 5 N·m (26 ± 4 ft lb)。
- 将工具 (A) 涂抹在螺柱的螺纹和锁紧螺母的配合面上。 将新的密封垫和排气旁通阀 (26) 置于排气弯头上。 安装新的锁紧螺母 (25)。 按照下述程序拧紧锁紧螺母 (25)。
- 将对角的两个锁紧螺母拧紧至扭矩为 25 ± 6 N·m (18 ± 4 lb ft)。
- 拧紧剩余的锁紧螺母至扭矩为 25 ± 6 N·m (18 ± 4 lb ft)。
- 拧紧 4 个锁紧螺母至扭矩为 47 ± 9 N·m (35 ± 7 lb ft)。
- 连接 3 个回转螺母 (24)。
Show/hide table
图 12 g06152450 - 安装绝缘件 (23)。
Show/hide table
图 13 g06152444 - 放置护罩 (22) 并安装 2 个螺栓 (22)。
Show/hide table
图 14 g06152304 - 放置护罩 (20) 并安装三个螺栓 (19)。
Show/hide table
图 15 g06152285 - 放置护罩 (18) 并安装 16 个螺栓 (17)。 10 个螺栓未显示。
Show/hide table
图 16 g06152261 - 放置护罩 (16) 并安装 14 个螺栓 (51)。 五个螺栓未显示。
Show/hide table
图 17 g06152245 - 放置护罩 (11)、 (12) 和 (13),然后安装 14 个螺栓 (14)。 两个螺栓未显示。
Show/hide table
图 18 g06152213 - 放置护罩 (7)、 (8) 和 (10),然后安装 12 个螺栓 (9)。
Show/hide table
图 19 g06151954 - 放置护罩 (5) 并安装 13 个螺栓 (6)。 其中一个螺栓未显示。
Show/hide table
图 20 g06151917 - 放置护罩 (1)、 (3) 和 (4),然后安装 11 个螺栓 (2)。
Show/hide table
图 11 | g06152452 |
Caterpillar Information System:
Installation and Removal of the 443-5682 Pressure Sensor Gp (In Cylinder Pressure Sensor) {1250, 1439, 1439} Installation and Removal of the 443-5682 Pressure Sensor Gp (In Cylinder Pressure Sensor) {1250, 1439, 1439}
Pump Electronic Monitoring System for Well Stimulation Pumps Speed/Timing - Test
C7.1 Engines and Generator Sets Glow Plug Starting Aid - Test
C7.1 Engines and Generator Sets Ether Starting Aid - Test
Pump Electronic Monitoring System for Well Stimulation Pumps Event Codes
Pump Electronic Monitoring System for Well Stimulation Pumps Diagnostic Trouble Codes
C7.1 Engines and Generator Sets Electrical Power Supply - Test
C7.1 Engines and Generator Sets Data Link Configuration Status - Test
C7.1 Engines and Generator Sets Data Link - Test
C7.1 Engines and Generator Sets Cooling Fan Speed - Test
C7.1 Engines and Generator Sets Cooling Fan Reversing - Test - Hydraulic Driven Fan
New Low-Pressure Fuel Pipes on Certain C3.4B Engines {1274} New Low-Pressure Fuel Pipes on Certain C3.4B Engines {1274}
Cat® VIMS Converter Functionality {7610, 7620} Cat® VIMS Converter Functionality {7610, 7620}
Pump Electronic Monitoring System for Well Stimulation Pumps Electrical Connectors - Inspect
G3516 TA Engine General Information (Electronic Control System)
G3500H Generator Set Engine Engine Sensors
Vibration Resonance May Cause A 105-15 Diagnostic Code To Activate On Certain C12.9 Marine Engines {1920, 1928} Vibration Resonance May Cause A 105-15 Diagnostic Code To Activate On Certain C12.9 Marine Engines {1920, 1928}
New Injector Sleeve on Certain C4.4 and C7.1 Engines {1254, 1290, 1713} New Injector Sleeve on Certain C4.4 and C7.1 Engines {1254, 1290, 1713}
New Injector Sleeve on Certain C4.4 and C7.1 Machine Engines {1254, 1290, 1713} New Injector Sleeve on Certain C4.4 and C7.1 Machine Engines {1254, 1290, 1713}
Diesel Exhaust Fluid (DEF) Pump Troubleshooting on Certain C4.4 Machine Engines {108J, 108K, 108T, 1901, 1920} Diesel Exhaust Fluid (DEF) Pump Troubleshooting on Certain C4.4 Machine Engines {108J, 108K, 108T, 1901, 1920}
C7.1 Engines and Generator Sets Idle Validation - Test
C7.1 Engines and Generator Sets Indicator Lamp Problem
C7.1 Engines and Generator Sets Injector Data Incorrect - Test
C7.1 Engines and Generator Sets Injector Solenoid - Test