Editing Truck and Material Lists
Note: The maximum list size is 250 entries for both "Truck List" and "Material List". Larger list sizes can lead to slower load times.
- Settings > Payload > List Management > Truck
- Select the truck you would like to add a new truck above or below.
- Press the "+" button.
Show/hide tableIllustration 1 g06133953 - Select if you want the new truck before or after the current truck.
- Press the "Before" or "After" button.
Show/hide tableIllustration 2 g06127484 - Select buttons to edit each property of the new truck.
- Enter the name that is desired to be shown on the display and stored.
- Enter the ID of the new truck.
- Enter the target weight of the new truck.
Show/hide tableIllustration 3 g06133915 - Select the "OK" button.
Show/hide table
Illustration 4 g06133985 - Select the "Save" button to program the list to the ECM.
- Select if you would like to save the changes or not.
- Press "OK" to save the changes.
- Press "Back" to go back to the list.
Show/hide tableIllustration 5 g06133997
Removing a Truck from Truck List
- Settings > Payload > List Management > Truck
Show/hide table
Illustration 6 g06133953 - Select the truck that you would like to remove.
Show/hide table
Illustration 7 g06133979 - Press "Delete".
- Press "OK" to delete the selected truck.
Adding a Material to Material List
- Settings > Payload > List Management > Material
Show/hide table
Illustration 8 g06134110 - Select the material that you would like to add a new material above or below.
- Press the "+" button.
- Select if you want the new material before or after the current material.
- Press "Before" or "After".
Show/hide tableIllustration 9 g06127767 - Select buttons to edit each property of the new material.
- Enter the name that is desired to be shown on the display and stored.
- Enter the ID of the new material.
- Enter the density of the new material.
Show/hide tableIllustration 10 g06134020 - Select the "OK" button.
Show/hide table
Illustration 11 g06134144 - Select the "Save" button to program the list to the ECM.
- Select if you would like to save the changes or not.
- Press "OK" to save the changes.
- Press "Back" to go back to the list.
Removing a Material from Material List
- Settings > Payload > List Management > Material
Show/hide table
Illustration 12 g06134110 - Select the material that you would like to remove.
Show/hide table
Illustration 13 g06127777 - Press "Delete".
- Press "OK" to delete the selected material.
Caterpillar Information System:
785G Off-Highway Truck Systems Electronic Control Module (ECM) - Replace
PM310, PM312, and PM313 Cold Planer Legs (Struts) - Lubricate
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Sample - Obtain
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Level - Check
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Filter - Replace
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil - Change
PM310, PM312, and PM313 Cold Planer Fuel Tank Water and Sediment - Drain
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine Oil Cooler - Remove and Install
PM310, PM312, and PM313 Cold Planer Engine Oil and Filter - Change
PM310, PM312, and PM313 Cold Planer Engine Oil Sample - Obtain
PM310, PM312, and PM313 Cold Planer Engine Oil Level - Check
PM310, PM312, and PM313 Cold Planer Engine Mounts - Inspect
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B} M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
797F and 797F XQ Off-Highway Trucks Magnetic Plug (Pump Drive, Hydraulic) - Check
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Ride Control Accumulator - Test and Charge
994K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
725C2 and 730C2 Articulated Truck Machine System Center Suspension Frame - Remove and Install
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine - Remove and Install
C175–16 Locomotive Engine Air in Fuel - Test
An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313} An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313}
725C2 and 730C2 Articulated Truck Machine System Rear Suspension Frame - Remove and Install
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251} An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251}
PM310, PM312, and PM313 Cold Planer Rotor Drive Belt - Inspect