Check the Hydraulic Tank Baffle on Certain Load Haul Dump Machines {5056} Caterpillar


Check the Hydraulic Tank Baffle on Certain Load Haul Dump Machines {5056}

Usage:

R1700G 8XZ
Load Haul Dump
R1600G (S/N: 9YZ1-UP)
R1700G (S/N: 8XZ1-UP)
R2900G (S/N: JLK1-UP; NLK1-UP)
R3000H (S/N: RCM1-UP; RCY1-UP)

Introduction

The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.

Problem



Illustration 1g06129743
View of the hydraulic tank with 123-8159 Baffle As (1).

Certain Load Haul Dump machines may experience cracking on 123-8159 Baffle As (1).



Illustration 2g06129747

Check both sides of 123-8159 Baffle As for cracking in the locations shown in Illustration 2.

Solution

Caterpillar is aware of the problem, but an interim repair has not been defined. Replace with same part, and refer to the instructions below.

  • Submit a Dealer Solution Network (DSN) ticket quoting CPI number 377310

  • Request that the Tier 1 representative, transfer your ticket to an available Tier 2 representative for Caterpillar Underground Mining - Base Machine

  • The Tier 2 representative will request the machine serial number, machine operating hours

Caterpillar Information System:

Check the Tilt Lever on R3000H Load Haul Dump Machines {6107} Check the Tilt Lever on R3000H Load Haul Dump Machines {6107}
Rework Procedure to Install the Counterweight and Treat the Subframe Weld on the C-Series Knuckleboom Loaders {0679, 4150, 7050, 7051, 7056} Rework Procedure to Install the Counterweight and Treat the Subframe Weld on the C-Series Knuckleboom Loaders {0679, 4150, 7050, 7051, 7056}
Replacing the Implement Pump on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {3203, 5070, 5073} Replacing the Implement Pump on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {3203, 5070, 5073}
XT6 ES Hose Replacement Procedure on Certain Asphalt Compactors {5057} XT6 ES Hose Replacement Procedure on Certain Asphalt Compactors {5057}
A New Procedure to Install the Front Axle Grease Line Protective Cover Is Now Available on Certain C & C2 Series Articulated Trucks {0679, 3013, 3278, 3282, 7150, 7450, 7510, 795C} A New Procedure to Install the Front Axle Grease Line Protective Cover Is Now Available on Certain C & C2 Series Articulated Trucks {0679, 3013, 3278, 3282, 7150, 7450, 7510, 795C}
An Improved Coupler Cylinder for Pin Grabber Is Now Used on Certain Excavators {5133} An Improved Coupler Cylinder for Pin Grabber Is Now Used on Certain Excavators {5133}
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Water Pump - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Rotor Drive Clutch - Remove and Install
C7.1 Engines and Generator Sets Valve Lash Is Excessive
C7.1 Engines and Generator Sets Power Is Intermittently Low or Power Cutout Is Intermittent
C7.1 Engines and Generator Sets Oil Pressure Is Low
C7.1 Engines and Generator Sets Oil Contains Fuel
990K Wheel Loader Systems Steering Control Support
980L Tier 3 Wheel Loader Machine System Window Wiper and Wiper Motor (Front) - Remove and Install
980L Tier 3 Wheel Loader Machine System Window Wiper and Wiper Motor (Rear) - Remove and Install
980L Tier 3 Wheel Loader Machine System Seat - Remove and Install
Improved Modular Handle (Hoist) Is Now Used on Certain Large Off-Highway Trucks {3065, 5000, 5063, 5705} Improved Modular Handle (Hoist) Is Now Used on Certain Large Off-Highway Trucks {3065, 5000, 5063, 5705}
Procedure for Installing a Locking Set Screw into the Shift Handle on Certain Off-Highway Trucks {5063, 5705} Procedure for Installing a Locking Set Screw into the Shift Handle on Certain Off-Highway Trucks {5063, 5705}
XT6 ES Hose Replacement Procedure on Certain Soil Compactors {3154} XT6 ES Hose Replacement Procedure on Certain Soil Compactors {3154}
994K Wheel Loader Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
Proper Maintenance Improves the Performance of the Circle Drive for Certain Motor Graders {5207} Proper Maintenance Improves the Performance of the Circle Drive for Certain Motor Graders {5207}
Measure the U-Cup Seal Groove on the Gland in the Front Suspension Group on Certain 795F and 797 Off-Highway Trucks {0756, 7200, 7201, 7555} Measure the U-Cup Seal Groove on the Gland in the Front Suspension Group on Certain 795F and 797 Off-Highway Trucks {0756, 7200, 7201, 7555}
730C and 730C2 EJECTOR Articulated Truck Systems Transmission Control (Shift Lever) - Calibrate
A Factory MineStar Ready Option and Retrofit Instructions are Now Available on Certain Motor Graders {7605, 7610, 7620} A Factory MineStar Ready Option and Retrofit Instructions are Now Available on Certain Motor Graders {7605, 7610, 7620}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.